Woodworking (rec.woodworking) Discussion forum covering all aspects of working with wood. All levels of expertise are encouraged to particiapte.

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
  #1   Report Post  
 
Posts: n/a
Default Bending wood and making dice

Used to carpentry, I usually make puzzles/brainteasers etc. Recently I
joined a games group and dice are involved. Not just 6 sided die. Well
I was wondering on how I would go about making a dice cup that can be
used to to store the dice too. Since I have no access to a lathe I
can't use that option, so I hunted in the workshop and found a sheet of
ply wood 1/16 thick 4 inches wide. Perfect size for my dice cup.
Trouble is how do I go about bending this into a perfect circle. I did
some research and found steaming is an option but I'm short on space
and funds to build a steamer. Is there any other option I could use?
And can plywood be bent around into a perfect cylinder?

Also any ideas on making dice, looks like an interesting project to
try. Should be easy with a 6 sided die but the others should be a
laugh, especially the 20 sided.[:-?]

  #2   Report Post  
tillius
 
Posts: n/a
Default

You could try using a kerfing technique to bend the plywood, although,
at 1/16" thick, you'd have to make a very shallow kerf.

If you had 1/16" thick solid wood, you could steam bend it. Can't do
that with plywood as the laminate glue may fail.

Tillman


Warning: Don't waste your money on 150,000+ woodworking plans on eBay.
Get more for free - links to a huge number of woodworking plans:
http://home.comcast.net/~tillman_ste...kinglinks.html

  #3   Report Post  
Richard Cline
 
Posts: n/a
Default

In article .com,
" wrote:

You can try an experiment with a heat gun. Anchor one end of your wood,
then heat it with the gun and wrap it around the mandril. You would
have a fair chance of success with a wood like cherry or oak but plywood
is an unknown.

Dick


Used to carpentry, I usually make puzzles/brainteasers etc. Recently I
joined a games group and dice are involved. Not just 6 sided die. Well
I was wondering on how I would go about making a dice cup that can be
used to to store the dice too. Since I have no access to a lathe I
can't use that option, so I hunted in the workshop and found a sheet of
ply wood 1/16 thick 4 inches wide. Perfect size for my dice cup.
Trouble is how do I go about bending this into a perfect circle. I did
some research and found steaming is an option but I'm short on space
and funds to build a steamer. Is there any other option I could use?
And can plywood be bent around into a perfect cylinder?

Also any ideas on making dice, looks like an interesting project to
try. Should be easy with a 6 sided die but the others should be a
laugh, especially the 20 sided.[:-?]

  #4   Report Post  
Buddy Matlosz
 
Posts: n/a
Default

Hi Freak,

I have a feeling you won't have any luck making a cylinder of that size by
either kerf- or steam-bending. One alternative would be to use square stock
and bore a hole with a Forstner bit. You could also chamfer the outside
corners to create an octagonal cross-section. A square or octagonal shape
might add more novelty to the cup's appearance than a cylindrical one.

B.

wrote in message
oups.com...
Used to carpentry, I usually make puzzles/brainteasers etc. Recently I
joined a games group and dice are involved. Not just 6 sided die. Well
I was wondering on how I would go about making a dice cup that can be
used to to store the dice too. Since I have no access to a lathe I
can't use that option, so I hunted in the workshop and found a sheet of
ply wood 1/16 thick 4 inches wide. Perfect size for my dice cup.
Trouble is how do I go about bending this into a perfect circle. I did
some research and found steaming is an option but I'm short on space
and funds to build a steamer. Is there any other option I could use?
And can plywood be bent around into a perfect cylinder?

Also any ideas on making dice, looks like an interesting project to
try. Should be easy with a 6 sided die but the others should be a
laugh, especially the 20 sided.[:-?]



  #5   Report Post  
pray4surf
 
Posts: n/a
Default


: And can plywood be bent around into a perfect cylinder?
:

As another mentioned, you probably wouldn't bet able to bend the plywood
tight enough. But if you can get your hands on some veneer, couldn't you
simply bend each layer around a form and build it up layer by layer?

Rick




  #7   Report Post  
gregg
 
Posts: n/a
Default


If you go to my web page:

http://home.comcast.net/~saville/sand_glasses.htm

You will see, on the top sandglass, bent wood that forms the cylinders that
hold the sandglass in place. For this application I bought some veneer and
boiled it for a few minutes. It bent easily.

However the run of the grain was not along the long length of the veneer.
So I cut out a piece such that the grain ran parallel to the enges of the
cylinder. This avoids breaking while bending.


Gregg

Replicas of 15th-19th century nautical navigational instruments:

http://home.comcast.net/~saville/backstaffhome.html

Restoration of my 82 year old Herreshoff S-Boat sailboat:

http://home.comcast.net/~saville/SBOATrestore.htm

Steambending FAQ with photos:

http://home.comcast.net/~saville/Steambend.htm



wrote:

Used to carpentry, I usually make puzzles/brainteasers etc. Recently I
joined a games group and dice are involved. Not just 6 sided die. Well
I was wondering on how I would go about making a dice cup that can be
used to to store the dice too. Since I have no access to a lathe I
can't use that option, so I hunted in the workshop and found a sheet of
ply wood 1/16 thick 4 inches wide. Perfect size for my dice cup.
Trouble is how do I go about bending this into a perfect circle. I did
some research and found steaming is an option but I'm short on space
and funds to build a steamer. Is there any other option I could use?
And can plywood be bent around into a perfect cylinder?

Also any ideas on making dice, looks like an interesting project to
try. Should be easy with a 6 sided die but the others should be a
laugh, especially the 20 sided.[:-?]


  #8   Report Post  
TeamCasa
 
Posts: n/a
Default


Since I have no access to a lathe I
can't use that option, so I hunted in the workshop and found a sheet of
ply wood 1/16 thick 4 inches wide.
Is there any other option I could use?
And can plywood be bent around into a perfect cylinder?


Start with square stock, (glued-up in necessary), chuck it into a drill
press,
(see http://www.toolcenter.com/Vertilathe.html , or just make your own
version)
Make it round, then use a forstner bit to bore the hole.

Dave


  #9   Report Post  
HerHusband
 
Posts: n/a
Default

I was wondering on how I would go about making a dice cup that can be
used to to store the dice too. Since I have no access to a lathe I
can't use that option


Just a few ideas...

1. A square container? Much easier to build if you don't NEED a round dice
cup. You could expand on the idea by making an 8 sided container instead of
4 sided. Easier to grip than a circular cup anyway...

2. Make a circle cutting jig for your router and straight cutting bit. Cut
out the outer circle, then the inner circle. This would leave you with a
"donut". Glue together a stack of these and one on the bottom and you've
got a cup. You could even get fancy with alternating wood types.

3. Make a variation of a "bandsaw box". Draw the container on a solid block
of wood, then cut it out on a bandsaw. Glue the pieces back together and
you're done. You could get creative with the shape using this approach.

4. Take a solid chunk of wood and slowly carve out the inside and outside
with chisels and sandpaper. Alternative tools could include a "Dremel"
rotary tool, or carving knives. Sounds like a good project to do while
sitting out on the porch. You could get creative with the shape and wood
here too, maybe carve it out of a tree burl, or a stump or something
similar.

Also any ideas on making dice, looks like an interesting project to
try. Should be easy with a 6 sided die but the others should be a
laugh, especially the 20 sided.[:-?]


No idea on that one. Maybe use a tablesaw to cut "V" grooves in a board,
then set the saw back to 90 degrees and cut the dice apart. It would take a
bit of setup and experimentation, but I would think it would work?

Anthony
  #10   Report Post  
Prometheus
 
Posts: n/a
Default

On 6 Jan 2005 17:38:04 -0800, "
wrote:

Used to carpentry, I usually make puzzles/brainteasers etc. Recently I
joined a games group and dice are involved. Not just 6 sided die. Well
I was wondering on how I would go about making a dice cup that can be
used to to store the dice too. Since I have no access to a lathe I
can't use that option, so I hunted in the workshop and found a sheet of
ply wood 1/16 thick 4 inches wide. Perfect size for my dice cup.
Trouble is how do I go about bending this into a perfect circle. I did
some research and found steaming is an option but I'm short on space
and funds to build a steamer. Is there any other option I could use?
And can plywood be bent around into a perfect cylinder?


You could get some flat solid stock, and cut out circles with a
bandsaw jig or jigsaw, then glue them together. Same thing could be
done with the plywood, though it probably wouldn't look as good,
unless you've got some really, really nice plywood. More than likely,
you'll be needing to do a bit of hand work with it, smoothing things
down with a rasp and sanding a lot, but I guess it just depends on how
badly you want a wooden dice cup! FWIW, you could also get yourself
one of those cheap little Wilton lathes for $60-70 and give turning
one a try.

Also any ideas on making dice, looks like an interesting project to
try. Should be easy with a 6 sided die but the others should be a
laugh, especially the 20 sided.[:-?]


Google for Icosahedrons (20-sided geometric forms) for angles. Or
Polyhedrons for other numbers of sides. With careful angle settings
on the tablesaw and a couple of jigs, it *should* be possible (though
not necessarily easy!)
Aut inveniam viam aut faciam


  #11   Report Post  
TrailRat
 
Posts: n/a
Default

I should really point out that I have no powered bench tools. I mainly
work with hand tools and handheld power tools. I have in my power tool
collection a router, jigsaw, circular saw and a belt sander. I also
have a drill which doubles up as drill press and it has a stand so I
can attach a grinding wheel so I can sharpen my chisels. The Wilthon
lathe sound like my price range but do they ship over here in UK.

Going to try everyones technique at least once see what I like the look
of. The ply wood is use is either birch, oak, teak or cherry venered.
Makes the puzzles cheap to make without looking cheap.

  #12   Report Post  
mark
 
Posts: n/a
Default


"TrailRat" wrote in message
ups.com...
I should really point out that I have no powered bench tools. I mainly
work with hand tools and handheld power tools. I have in my power tool
collection a router, jigsaw, circular saw and a belt sander. I also
have a drill which doubles up as drill press and it has a stand so I
can attach a grinding wheel so I can sharpen my chisels. The Wilthon
lathe sound like my price range but do they ship over here in UK.

Going to try everyones technique at least once see what I like the look
of. The ply wood is use is either birch, oak, teak or cherry venered.
Makes the puzzles cheap to make without looking cheap.



Here's an idea, since you have a drill press. I made a cup (drinking, not
dice) for a friend of mine like this.

Go out in the woods and find a birch tree or branch the same diameter you
want your cup. Cut a section out.

Get a big forstner bit, and drill out the center. I did this, leaving
about a 3/8" wall. It dried fine with no checking.


  #13   Report Post  
no_way-no_how
 
Posts: n/a
Default

Bending trick I learned when building acoustic guitars while stationed in
Panama.

Use and iron pipe clamped into a vise, heat the pipe with a torch (to almost
red hot). Place folded wet towels onto the pipe (instant steam) and bend
your wood right over the top of the towels, the idea here is that the steam
generated off the towels allows the wood fibers to move relative to each
other.

Notes on this technique:
1. Thoroughly soak the wood you will be bending by submerging in water for
a couple of days.
2. Keep a bucket handy and resoak the rags regularly, also reheat the pipe
regularly.
3. Don't force the wood to bend it. Just place it on the pipe with very
little pressure, you will actually feel it start to give a little at a time.
4. It helps to have two people for this process (one to handle the torch
and one to handle the wood).
5. You may not be able to bend plywood using this method due to the grain
orientation of the various plys, and the adhesive used to hold the whole
mess together.
6. When done bending, clamp you work into a form (roughly shaped like the
final project) and let is cool and dry for about a day.

This is also a great method because a number of different diameter iron or
steel pipes is a lot cheaper than a number of different diameter steam
benders.


wrote in message
oups.com...
Used to carpentry, I usually make puzzles/brainteasers etc. Recently I
joined a games group and dice are involved. Not just 6 sided die. Well
I was wondering on how I would go about making a dice cup that can be
used to to store the dice too. Since I have no access to a lathe I
can't use that option, so I hunted in the workshop and found a sheet of
ply wood 1/16 thick 4 inches wide. Perfect size for my dice cup.
Trouble is how do I go about bending this into a perfect circle. I did
some research and found steaming is an option but I'm short on space
and funds to build a steamer. Is there any other option I could use?
And can plywood be bent around into a perfect cylinder?

Also any ideas on making dice, looks like an interesting project to
try. Should be easy with a 6 sided die but the others should be a
laugh, especially the 20 sided.[:-?]




  #15   Report Post  
Posted to rec.woodworking
external usenet poster
 
Posts: 67
Default Bending wood and making dice

Boiling is always a good substitute for steaming......I am not sure about
bending plywood though.
Dave




  #16   Report Post  
Posted to rec.woodworking
external usenet poster
 
Posts: 20
Default Bending wood and making dice

I think this might work. http://www.melright.com/busker/jsart35.htm

Bob


"Oleg Lego" wrote in message
...
The entity posted thusly:

Used to carpentry, I usually make puzzles/brainteasers etc. Recently I
joined a games group and dice are involved. Not just 6 sided die. Well
I was wondering on how I would go about making a dice cup that can be
used to to store the dice too. Since I have no access to a lathe I
can't use that option, so I hunted in the workshop and found a sheet of
ply wood 1/16 thick 4 inches wide. Perfect size for my dice cup.
Trouble is how do I go about bending this into a perfect circle. I did
some research and found steaming is an option but I'm short on space
and funds to build a steamer. Is there any other option I could use?
And can plywood be bent around into a perfect cylinder?

Also any ideas on making dice, looks like an interesting project to
try. Should be easy with a 6 sided die but the others should be a
laugh, especially the 20 sided.[:-?]


Plywood will not readily form a perfect circle because of its
construction, and because the ends need to butt together, leaving a
weak spot that will always be out of whack.

I would form it with steamed veneer. Rolls of various widths are
available from better wood places (don't bother with the BORG (Home
Depot or Lowes). It's available in a lot of different woods.

I suggest posting your question on rec.woodworking for a better range
of ideas.



  #17   Report Post  
Posted to rec.woodworking
external usenet poster
 
Posts: 172
Default Bending wood and making dice

Oleg Lego wrote:

The entity posted thusly:

Used to carpentry, I usually make puzzles/brainteasers etc. Recently I
joined a games group and dice are involved. Not just 6 sided die. Well
I was wondering on how I would go about making a dice cup that can be
used to to store the dice too. Since I have no access to a lathe I
can't use that option, so I hunted in the workshop and found a sheet of
ply wood 1/16 thick 4 inches wide. Perfect size for my dice cup.
Trouble is how do I go about bending this into a perfect circle. I did
some research and found steaming is an option but I'm short on space
and funds to build a steamer.


What's a dice cup, about 2.5 inch diameter by 3 inches high? That means
that you need pieces about 8x3 steamed. You should be able to do that on
the kitchen stove in a stockpot.

Is there any other option I could use?
And can plywood be bent around into a perfect cylinder?

Also any ideas on making dice, looks like an interesting project to
try. Should be easy with a 6 sided die but the others should be a
laugh, especially the 20 sided.[:-?]


Plywood will not readily form a perfect circle because of its
construction, and because the ends need to butt together, leaving a
weak spot that will always be out of whack.

I would form it with steamed veneer. Rolls of various widths are
available from better wood places (don't bother with the BORG (Home
Depot or Lowes). It's available in a lot of different woods.

I suggest posting your question on rec.woodworking for a better range
of ideas.


--
--John
to email, dial "usenet" and validate
(was jclarke at eye bee em dot net)
  #18   Report Post  
Posted to rec.woodworking
external usenet poster
 
Posts: 7
Default Bending wood and making dice

The Oleg Lego entity posted thusly:

Plywood will not readily form a perfect circle because of its
construction, and because the ends need to butt together, leaving a
weak spot that will always be out of whack.

I would form it with steamed veneer. Rolls of various widths are
available from better wood places (don't bother with the BORG (Home
Depot or Lowes). It's available in a lot of different woods.

I suggest posting your question on rec.woodworking for a better range
of ideas.


Sorry about that, folks! I was perusing another newsgroup, and
somehow, I must have hit a key or key combination that put me into a
local folder containing postings from the Wreck. I thought I was
answering a current posting, from the other newsgroup. Turns out I was
answering a post made in January.

Oh well, prompted another few ideas. :-)

Reply
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules

Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Steam Bending Lumber - Any Good Sites Big John Woodworking 2 December 26th 04 06:30 PM
FAQ - Steambending gregg Woodworking 0 December 26th 04 02:06 PM
Philippines areas for wood carving & furniture making Phillip Wu Woodworking 0 August 30th 04 12:37 AM
Ok, so how much more do I need to get started making real wood projects Bob Davis Woodworking 47 March 26th 04 12:22 PM
How Much Wood Are You Willing to “Waste” (Long) charlie b Woodworking 7 March 4th 04 06:05 PM


All times are GMT +1. The time now is 09:22 PM.

Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 DIYbanter.
The comments are property of their posters.
 

About Us

"It's about DIY & home improvement"