Home |
Search |
Today's Posts |
|
Woodworking (rec.woodworking) Discussion forum covering all aspects of working with wood. All levels of expertise are encouraged to particiapte. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
|
#1
|
|||
|
|||
What type of wood is this?
I recently purchased a baby changing table for $20.00 because it looked
rickety and cheap. My goal was to do a quick refinish job and tighten the joints so it would be in better condition. (My plan is not to make something that will last forever, just long enough to get our baby out of diapers). The existing coating was a white pickled looking finish that was peeling away and seemed more like melamine than finish. I started sanding the pieces today and the wood underneath actually seems to be quite nice. It seems very dense and sands very smooth without splintering. (My previous project was an oak dresser that splintered if I used any kind of low-grit sandpaper on a random-pad sander, so this seemed much easier to work with). In addition to this, the grain on the wood is actually quite attractive to me and it seems strange it would be nearly covered by the dull white finish. I am not sure if that was the original factory finish or if it was added by one of the previous owners. Anyways, I was just curious if someone could help me figure out what kind of wood it is? Comparing the grain to some desks I have, it looks like it might be birch, but I am no expert, so I figure I would open this up to the masses! The pictures are he http://www.kryogenic.org/wood/wood.htm Let me know if you can identify this. -- Thanks, David |
#2
|
|||
|
|||
my guess is white maple. i'd put money on it. if so, it's a very hard,
durable wood, and with a little refinishing it'll be beautiful. granted, i might lose my money, but it wouldn't be the first time. good luck, -- dz David wrote: I recently purchased a baby changing table for $20.00 because it looked rickety and cheap. My goal was to do a quick refinish job and tighten the joints so it would be in better condition. (My plan is not to make something that will last forever, just long enough to get our baby out of diapers). The existing coating was a white pickled looking finish that was peeling away and seemed more like melamine than finish. I started sanding the pieces today and the wood underneath actually seems to be quite nice. It seems very dense and sands very smooth without splintering. (My previous project was an oak dresser that splintered if I used any kind of low-grit sandpaper on a random-pad sander, so this seemed much easier to work with). In addition to this, the grain on the wood is actually quite attractive to me and it seems strange it would be nearly covered by the dull white finish. I am not sure if that was the original factory finish or if it was added by one of the previous owners. Anyways, I was just curious if someone could help me figure out what kind of wood it is? Comparing the grain to some desks I have, it looks like it might be birch, but I am no expert, so I figure I would open this up to the masses! The pictures are he http://www.kryogenic.org/wood/wood.htm Let me know if you can identify this. |
#3
|
|||
|
|||
"David Zaret" skrev i melding m... my guess is white maple. i'd put money on it. if so, it's a very hard, durable wood, and with a little refinishing it'll be beautiful. granted, i might lose my money, but it wouldn't be the first time. Could it not be beechwood? Especially the sideshot of a plank, (the dotty part) seems to indicate to me that beech is a strong possibility. Bjarte |
#4
|
|||
|
|||
"Bjarte Runderheim" wrote in message ...
Could it not be beechwood? Especially the sideshot of a plank, (the dotty part) seems to indicate to me that beech is a strong possibility. The ray flecks in beech are more prominant, though less so than in oak. A fair amount of modern 'maple' furniture is made from beech, just like the oak furniture at K-Mart is made from rubber wood. -- FF |
#5
|
|||
|
|||
Won't lose it to me. Soft maple is my choice, too. If the color's off,
could be something like alder, though. What it definitely is not is birch. "David Zaret" wrote in message m... my guess is white maple. i'd put money on it. if so, it's a very hard, durable wood, and with a little refinishing it'll be beautiful. granted, i might lose my money, but it wouldn't be the first time. Anyways, I was just curious if someone could help me figure out what kind of wood it is? Comparing the grain to some desks I have, it looks like it might be birch, but I am no expert, so I figure I would open this up to the masses! The pictures are he http://www.kryogenic.org/wood/wood.htm Let me know if you can identify this. |
#7
|
|||
|
|||
Maple me thinks....mjh
|
#8
|
|||
|
|||
"Mike Hide" wrote in message news:LnlWc.74844$TI1.67537@attbi_s52...
Maple me thinks....mjh Yep, that's maple. The clincher is the tiny ray-flecks (not pores) in the quarter sawn grain that show up in maple and cherry only when the grain is very close to perpendicular to the surface. -- FF |
#9
|
|||
|
|||
So the consensus seems to be Maple. I am amazed. Seems like Maple is pretty
expensive but this thing wasnt well taken care of. Thanks for all the help! -- Thanks, David W. Lovell ( Intrepid ) "Fred the Red Shirt" wrote in message m... "Mike Hide" wrote in message news:LnlWc.74844$TI1.67537@attbi_s52... Maple me thinks....mjh Yep, that's maple. The clincher is the tiny ray-flecks (not pores) in the quarter sawn grain that show up in maple and cherry only when the grain is very close to perpendicular to the surface. -- FF |
#10
|
|||
|
|||
"David" wrote in
: So the consensus seems to be Maple. I am amazed. Seems like Maple is pretty expensive but this thing wasnt well taken care of. Thanks for all the help! Could be soft maple, which isn't all that pricey, or all that soft. Small quantities of 4/4, s2s1e, in the SF Bay Area, $3.10/bf Patriarch |
#11
|
|||
|
|||
"David" wrote in message . ..
So the consensus seems to be Maple. I am amazed. Seems like Maple is pretty expensive but this thing wasnt well taken care of. Expensive compared to what? In most places Maple is cheaper than walnut, cherry, mahogany, or birch, and it is harder and more durable than those. Often Oak is cheaper than maple, but not by a lot. I think you'll find that a lot of school furniture was made of maple. I think the student deks back when I was in school were made from maple ply and sheet steel, and the maple ply may have been maple all the way through. It was very tough stuff, usually outlasted the steel. -- FF |
#12
|
|||
|
|||
Well, I am not a connoisseur of wood pricing, but I know that paying $20.00
for this selection of nice wood seems to be much cheaper than I could buy even average pine at Home Depot or Rockler. So its not that this wood is necessarily comparatively expensive, just seems like its nicer than I would have expected for the price I paid. -- Thanks, David W. Lovell ( Intrepid ) "Fred the Red Shirt" wrote in message m... "David" wrote in message . .. So the consensus seems to be Maple. I am amazed. Seems like Maple is pretty expensive but this thing wasnt well taken care of. Expensive compared to what? In most places Maple is cheaper than walnut, cherry, mahogany, or birch, and it is harder and more durable than those. Often Oak is cheaper than maple, but not by a lot. I think you'll find that a lot of school furniture was made of maple. I think the student deks back when I was in school were made from maple ply and sheet steel, and the maple ply may have been maple all the way through. It was very tough stuff, usually outlasted the steel. -- FF |
#13
|
|||
|
|||
Fred the Red Shirt wrote:
"David" wrote in message . .. So the consensus seems to be Maple. I am amazed. Seems like Maple is pretty expensive but this thing wasnt well taken care of. Expensive compared to what? In most places Maple is cheaper than walnut, cherry, mahogany, or birch, and it is harder and more durable than those. Minor nit--"durable" usually refers to decay resistance--maple is not particularly good in that regard--walnut, cherry, and mahogany are all mure durable in that regard than maple. Often Oak is cheaper than maple, but not by a lot. I think you'll find that a lot of school furniture was made of maple. I think the student deks back when I was in school were made from maple ply and sheet steel, and the maple ply may have been maple all the way through. It was very tough stuff, usually outlasted the steel. -- --John Reply to jclarke at ae tee tee global dot net (was jclarke at eye bee em dot net) |
#14
|
|||
|
|||
Maple..
"David" wrote in message ... I recently purchased a baby changing table for $20.00 because it looked rickety and cheap. My goal was to do a quick refinish job and tighten the joints so it would be in better condition. (My plan is not to make something that will last forever, just long enough to get our baby out of diapers). The existing coating was a white pickled looking finish that was peeling away and seemed more like melamine than finish. I started sanding the pieces today and the wood underneath actually seems to be quite nice. It seems very dense and sands very smooth without splintering. (My previous project was an oak dresser that splintered if I used any kind of low-grit sandpaper on a random-pad sander, so this seemed much easier to work with). In addition to this, the grain on the wood is actually quite attractive to me and it seems strange it would be nearly covered by the dull white finish. I am not sure if that was the original factory finish or if it was added by one of the previous owners. Anyways, I was just curious if someone could help me figure out what kind of wood it is? Comparing the grain to some desks I have, it looks like it might be birch, but I am no expert, so I figure I would open this up to the masses! The pictures are he http://www.kryogenic.org/wood/wood.htm Let me know if you can identify this. -- Thanks, David |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
lathe - metal or wood? | Woodworking | |||
### micro-FAQ on wood # 008 | Woodworking | |||
New Chinese Furniture wood type | Woodworking | |||
How Much Wood Are You Willing to “Waste” (Long) | Woodworking | |||
Wood vs. "Faux" wood blinds... | Home Ownership |