Woodworking (rec.woodworking) Discussion forum covering all aspects of working with wood. All levels of expertise are encouraged to particiapte.

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
  #1   Report Post  
Posted to rec.woodworking
external usenet poster
 
Posts: 11
Default Mohagany planing

Hi,

I bought some African Mohagany and asked the lumber store to plane it
for me. After I got them, all boards come out having very bad mars on
it. Seems like a dull planer blade pulling the soft part of wood grain
together. It looks all ruined to me. But the store tells me that is
Mohagany looks like. Their theory is the same planer works fine for
other wood species.( it is true, I bought some oak and maple at the
same time. They all look good). I don't know what to do now. I was
going to use them for panel cabinet doors. Now I can't. The marks will
be all over the face of doors.( some are as deep as 1/8"). Just wonder
somebody here can help me with the following questions.
1. Is it normal for African Mohagany to be planed like this?
2. What is the best way to plane this type of wood?
3. Anyway to save these boards ( I bought a lot, around 100bf)
4. With mark on it, will that be fine for the cabinet?

Thank you!

Tom

  #2   Report Post  
Posted to rec.woodworking
Lee Lee is offline
external usenet poster
 
Posts: 194
Default Mohagany planing

1 NO
2 With a quality planer and SHARP blades
3 If they have enough stock left re-plane them.1/8" gouge???? my lawn mower
planes better than that.
4 Only if you feel the results are acceptable.
Sounds like they where in a hurry and made heavy cuts. I'd raise holy hell
for screwing up that costly a wood and demand replacing the wood. If they
are a reliable and responsible dealer they will admit there error.
wrote in message
oups.com...
Hi,

I bought some African Mohagany and asked the lumber store to plane it
for me. After I got them, all boards come out having very bad mars on
it. Seems like a dull planer blade pulling the soft part of wood grain
together. It looks all ruined to me. But the store tells me that is
Mohagany looks like. Their theory is the same planer works fine for
other wood species.( it is true, I bought some oak and maple at the
same time. They all look good). I don't know what to do now. I was
going to use them for panel cabinet doors. Now I can't. The marks will
be all over the face of doors.( some are as deep as 1/8"). Just wonder
somebody here can help me with the following questions.
1. Is it normal for African Mohagany to be planed like this?
2. What is the best way to plane this type of wood?
3. Anyway to save these boards ( I bought a lot, around 100bf)
4. With mark on it, will that be fine for the cabinet?

Thank you!

Tom



  #3   Report Post  
Posted to rec.woodworking
external usenet poster
 
Posts: 11
Default Mohagany planing

On Oct 19, 11:47 am, "Lee" wrote:
1 NO
2 With a quality planer and SHARP blades
3 If they have enough stock left re-plane them.1/8" gouge???? my lawn mower
planes better than that.
4 Only if you feel the results are acceptable.
Sounds like they where in a hurry and made heavy cuts. I'd raise holy hell
for screwing up that costly a wood and demand replacing the wood. If they
are a reliable and responsible dealer they will admit there wrote in message

oups.com...



Hi,


I bought some African Mohagany and asked the lumber store to plane it
for me. After I got them, all boards come out having very bad mars on
it. Seems like a dull planer blade pulling the soft part of wood grain
together. It looks all ruined to me. But the store tells me that is
Mohagany looks like. Their theory is the same planer works fine for
other wood species.( it is true, I bought some oak and maple at the
same time. They all look good). I don't know what to do now. I was
going to use them for panel cabinet doors. Now I can't. The marks will
be all over the face of doors.( some are as deep as 1/8"). Just wonder
somebody here can help me with the following questions.
1. Is it normal for African Mohagany to be planed like this?
2. What is the best way to plane this type of wood?
3. Anyway to save these boards ( I bought a lot, around 100bf)
4. With mark on it, will that be fine for the cabinet?


Thank you!


Tom- Hide quoted text -


- Show quoted text -


Thank you!

Tom

  #4   Report Post  
Posted to rec.woodworking
external usenet poster
 
Posts: 297
Default Mohagany planing

On Oct 19, 9:52 am, wrote:
Hi,

I bought some African Mohagany and asked the lumber store to plane it
for me. After I got them, all boards come out having very bad mars on
it. Seems like a dull planer blade pulling the soft part of wood grain
together. It looks all ruined to me. But the store tells me that is
Mohagany looks like. Their theory is the same planer works fine for
other wood species.( it is true, I bought some oak and maple at the
same time. They all look good). I don't know what to do now. I was
going to use them for panel cabinet doors. Now I can't. The marks will
be all over the face of doors.( some are as deep as 1/8"). Just wonder
somebody here can help me with the following questions.
1. Is it normal for African Mohagany to be planed like this?
2. What is the best way to plane this type of wood?
3. Anyway to save these boards ( I bought a lot, around 100bf)
4. With mark on it, will that be fine for the cabinet?

Thank you!

Tom


That's not the way my mahogony turns out. I sometimes get a little
fuzzy grain out of the planer, but it sands right out.
The place where I buy wood uses too fast a feed rate that leaves
scallops in the wood, so I always have them leave it an extra
sixteenth too thick so I can take 1/32 off each side on my Makita
planer at home. But I've never had them harm a board so much it
couldn't be cleaned up with a couple of passes. If you have planing
defects even 1/32 deep, I'd say they ruined it for its intended
purpose. I agree with Leon. Press them to replace the wood or give
your money back.

DonkeyHody
"In theory, theory and practice are the same, but in practice, they
are not."

  #5   Report Post  
Posted to rec.woodworking
Lee Lee is offline
external usenet poster
 
Posts: 194
Default Mohagany planing

You should give the name of the supplier in case others here might buy from
them so that they are aware of a possible problem.




  #6   Report Post  
Posted to rec.woodworking
external usenet poster
 
Posts: 11
Default Mohagany planing

On Oct 19, 1:29 pm, DonkeyHody wrote:
On Oct 19, 9:52 am, wrote:





Hi,


I bought some African Mohagany and asked the lumber store to plane it
for me. After I got them, all boards come out having very bad mars on
it. Seems like a dull planer blade pulling the soft part of wood grain
together. It looks all ruined to me. But the store tells me that is
Mohagany looks like. Their theory is the same planer works fine for
other wood species.( it is true, I bought some oak and maple at the
same time. They all look good). I don't know what to do now. I was
going to use them for panel cabinet doors. Now I can't. The marks will
be all over the face of doors.( some are as deep as 1/8"). Just wonder
somebody here can help me with the following questions.
1. Is it normal for African Mohagany to be planed like this?
2. What is the best way to plane this type of wood?
3. Anyway to save these boards ( I bought a lot, around 100bf)
4. With mark on it, will that be fine for the cabinet?


Thank you!


Tom


That's not the way my mahogony turns out. I sometimes get a little
fuzzy grain out of the planer, but it sands right out.
The place where I buy wood uses too fast a feed rate that leaves
scallops in the wood, so I always have them leave it an extra
sixteenth too thick so I can take 1/32 off each side on my Makita
planer at home. But I've never had them harm a board so much it
couldn't be cleaned up with a couple of passes. If you have planing
defects even 1/32 deep, I'd say they ruined it for its intended
purpose. I agree with Leon. Press them to replace the wood or give
your money back.

DonkeyHody
"In theory, theory and practice are the same, but in practice, they
are not."- Hide quoted text -

- Show quoted text -


DonkeyHody,

Thank you for the suggestion! I called them up and they are pretty
good on services. They agree to refund the money, but they said they
can't do a better job than that. It is just a nature of crossgrain. I
think I should take your suggestion to ask them plane it to 1/16 more.
Just wonder what type of planer do you use? I am thinking of returning
some and leave some relatively good ones to keep my work going, since
some part may not need perfect lumber. And buy some more to ask them
to plane it to 1/16 to.

Tom

  #7   Report Post  
Posted to rec.woodworking
external usenet poster
 
Posts: 11
Default Mohagany planing

On Oct 19, 1:29 pm, DonkeyHody wrote:
On Oct 19, 9:52 am, wrote:





Hi,


I bought some African Mohagany and asked the lumber store to plane it
for me. After I got them, all boards come out having very bad mars on
it. Seems like a dull planer blade pulling the soft part of wood grain
together. It looks all ruined to me. But the store tells me that is
Mohagany looks like. Their theory is the same planer works fine for
other wood species.( it is true, I bought some oak and maple at the
same time. They all look good). I don't know what to do now. I was
going to use them for panel cabinet doors. Now I can't. The marks will
be all over the face of doors.( some are as deep as 1/8"). Just wonder
somebody here can help me with the following questions.
1. Is it normal for African Mohagany to be planed like this?
2. What is the best way to plane this type of wood?
3. Anyway to save these boards ( I bought a lot, around 100bf)
4. With mark on it, will that be fine for the cabinet?


Thank you!


Tom


That's not the way my mahogony turns out. I sometimes get a little
fuzzy grain out of the planer, but it sands right out.
The place where I buy wood uses too fast a feed rate that leaves
scallops in the wood, so I always have them leave it an extra
sixteenth too thick so I can take 1/32 off each side on my Makita
planer at home. But I've never had them harm a board so much it
couldn't be cleaned up with a couple of passes. If you have planing
defects even 1/32 deep, I'd say they ruined it for its intended
purpose. I agree with Leon. Press them to replace the wood or give
your money back.

DonkeyHody
"In theory, theory and practice are the same, but in practice, they
are not."- Hide quoted text -

- Show quoted text -


I called them up and they are not bad on customer services. They are
willing to refund all the lumbers but they can do a better planing job
on it for me. I probably will take your method. What type of planer
you are using? I will probably return some and keep some good ones for
my project going, since some part may not need perfect pieces.

Thank you!

Tom

  #8   Report Post  
Posted to rec.woodworking
Lee Lee is offline
external usenet poster
 
Posts: 194
Default Mohagany planing


Glad to hear they'll help. I have a 734 Dewalt. Not the best but it does a
great job and the knives are very easy to turn or replace.
If they can't do better then they must have a problem using there planer.Ask
them if they can make lighter cuts.


  #9   Report Post  
Posted to rec.woodworking
external usenet poster
 
Posts: 2,047
Default Mohagany planing


wrote:


Thank you for the suggestion! I called them up and they are pretty
good on services. They agree to refund the money, but they said they
can't do a better job than that. It is just a nature of crossgrain.


Have them plane new stock +1/8", then go to a commercial drum sanding
shop and have them sand it to size.

Check with a local top shop if you have trouble finding a sanding
shop.

Lew


  #10   Report Post  
Posted to rec.woodworking
external usenet poster
 
Posts: 297
Default Mohagany planing

On Oct 19, 2:23 pm, wrote:
On Oct 19, 1:29 pm, DonkeyHody wrote:





On Oct 19, 9:52 am, wrote:


Hi,


I bought some African Mohagany and asked the lumber store to plane it
for me. After I got them, all boards come out having very bad mars on
it. Seems like a dull planer blade pulling the soft part of wood grain
together. It looks all ruined to me. But the store tells me that is
Mohagany looks like. Their theory is the same planer works fine for
other wood species.( it is true, I bought some oak and maple at the
same time. They all look good). I don't know what to do now. I was
going to use them for panel cabinet doors. Now I can't. The marks will
be all over the face of doors.( some are as deep as 1/8"). Just wonder
somebody here can help me with the following questions.
1. Is it normal for African Mohagany to be planed like this?
2. What is the best way to plane this type of wood?
3. Anyway to save these boards ( I bought a lot, around 100bf)
4. With mark on it, will that be fine for the cabinet?


Thank you!


Tom


That's not the way my mahogony turns out. I sometimes get a little
fuzzy grain out of the planer, but it sands right out.
The place where I buy wood uses too fast a feed rate that leaves
scallops in the wood, so I always have them leave it an extra
sixteenth too thick so I can take 1/32 off each side on my Makita
planer at home. But I've never had them harm a board so much it
couldn't be cleaned up with a couple of passes. If you have planing
defects even 1/32 deep, I'd say they ruined it for its intended
purpose. I agree with Leon. Press them to replace the wood or give
your money back.


DonkeyHody
"In theory, theory and practice are the same, but in practice, they
are not."- Hide quoted text -


- Show quoted text -


DonkeyHody,

Thank you for the suggestion! I called them up and they are pretty
good on services. They agree to refund the money, but they said they
can't do a better job than that. It is just a nature of crossgrain. I
think I should take your suggestion to ask them plane it to 1/16 more.
Just wonder what type of planer do you use? I am thinking of returning
some and leave some relatively good ones to keep my work going, since
some part may not need perfect lumber. And buy some more to ask them
to plane it to 1/16 to.

Tom- Hide quoted text -

- Show quoted text -


My planer is an old 15" Makita model 2040. I don't think they even
make them anymore. It's underpowered and very slow, but it leaves a
good finish that requires very little sanding. You should be able to
get much better results that you've seen so far from just about any
planer if it's set up properly.

DonkeyHody
"Good judgement comes from experience. Experience comes from poor
judgement."



  #11   Report Post  
Posted to rec.woodworking
external usenet poster
 
Posts: 11
Default Mohagany planing

On Oct 19, 1:29 pm, DonkeyHody wrote:
On Oct 19, 9:52 am, wrote:





Hi,


I bought some African Mohagany and asked the lumber store to plane it
for me. After I got them, all boards come out having very bad mars on
it. Seems like a dull planer blade pulling the soft part of wood grain
together. It looks all ruined to me. But the store tells me that is
Mohagany looks like. Their theory is the same planer works fine for
other wood species.( it is true, I bought some oak and maple at the
same time. They all look good). I don't know what to do now. I was
going to use them for panel cabinet doors. Now I can't. The marks will
be all over the face of doors.( some are as deep as 1/8"). Just wonder
somebody here can help me with the following questions.
1. Is it normal for African Mohagany to be planed like this?
2. What is the best way to plane this type of wood?
3. Anyway to save these boards ( I bought a lot, around 100bf)
4. With mark on it, will that be fine for the cabinet?


Thank you!


Tom


That's not the way my mahogony turns out. I sometimes get a little
fuzzy grain out of the planer, but it sands right out.
The place where I buy wood uses too fast a feed rate that leaves
scallops in the wood, so I always have them leave it an extra
sixteenth too thick so I can take 1/32 off each side on my Makita
planer at home. But I've never had them harm a board so much it
couldn't be cleaned up with a couple of passes. If you have planing
defects even 1/32 deep, I'd say they ruined it for its intended
purpose. I agree with Leon. Press them to replace the wood or give
your money back.

DonkeyHody
"In theory, theory and practice are the same, but in practice, they
are not."- Hide quoted text -

- Show quoted text -


DonkeyHody,

Thank you for the suggestion! I called them up and they are pretty
good on services. They agree to refund the money, but they said they
can't do a better job than that. It is just a nature of crossgrain. I
think I should take your suggestion to ask them plane it to 1/16 more.
Just wonder what type of planer do you use? I am thinking of returning
some and leave some relatively good ones to keep my work going, since
some part may not need perfect lumber. And buy some more to ask them
to plane it to 1/16 to.

Tom

Reply
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules

Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
planing (doors) nospam[_2_] UK diy 19 October 12th 07 10:48 AM
Planing against the grain? Mac Woodworking 7 October 31st 05 03:04 AM
planing in Toronto David Grant Woodworking 6 June 13th 05 05:35 PM
Planing MDF Bert Coules UK diy 10 May 30th 05 10:41 AM
Planing Help Mike Woodworking 12 November 2nd 04 01:52 PM


All times are GMT +1. The time now is 10:30 AM.

Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 DIYbanter.
The comments are property of their posters.
 

About Us

"It's about DIY & home improvement"