thanks. Ill see if I can get set up with the SS method. The only thing I
should need to buy is a Honing guide. The rest I should have around.
"trs80" wrote in message
...
is there online somewhere a good tutorial on how to sharpen and maintain
chisels and block plane knifes? Also instruction on how to restore
chisles that have really banged up edges? Im needing to use blockplane
more and should sharped the blade.

I caught the end of the program on the DIY channel where he used 4 wet
stones to sharpen a block plane knife but not the entire thing. He would
take paper thin shavings off the edge of wood after sharpened. I have a
water wheel thing with single stone wheel in water well (I guess Tormek
like) that I inherited but not sure its the right thing to use by itself
as the wet stone approach on the DIY used 4 different stones.

Id probably only need to sharpen infrequently like once every 2-3 months
as its a weekend hobby thing.
Any thoughts appreciated.

thanks

On Jun 22, 4:41 pm, "trs80" wrote:
thanks. Ill see if I can get set up with the SS method. The only thing I
should need to buy is a Honing guide. The rest I should have around."trs80" wrote in message

...



is there online somewhere a good tutorial on how to sharpen and maintain
chisels and block plane knifes? Also instruction on how to restore
chisles that have really banged up edges? Im needing to use blockplane
more and should sharped the blade.

I caught the end of the program on the DIY channel where he used 4 wet
stones to sharpen a block plane knife but not the entire thing. He would
take paper thin shavings off the edge of wood after sharpened. I have a
water wheel thing with single stone wheel in water well (I guess Tormek
like) that I inherited but not sure its the right thing to use by itself
as the wet stone approach on the DIY used 4 different stones.

Id probably only need to sharpen infrequently like once every 2-3 months
as its a weekend hobby thing.
Any thoughts appreciated.

thanks- Hide quoted text -

- Show quoted text -

I am not a newbee or a oldtimer (except in age) and I have tried that
gambit, 1" belt sander (sucks), wet stones (works great if you have
the patience of a Buddist monk), Delta Wet Sharpener (hard to use, not
so hot results) SS (slow but works great) and a dedicated Wet Tool
Grinder (Tormek or Jet, mine is the the point of trying Jointer blades
(I find the cost of buying throw away planner blades outweighs the
value of sharpening them).

Here is what I am doing now:

For Chisles, Carving tools, scrapers, planes and chip breakers - I
religously use the Jet, this puts a great shallow hollow grind on
themwhich i then follow up with the SS to flatten the backs and then a
real fine grit (4000) water stone for removings the burrs. I use the
side of the Jet wet stone to flatten the scrapers.

For turning tools I use the Delta wet grinder on the dry white stone
for during the job sharpenings, periodically, I use the Jet to get
real nice clean edges on them.

I have yet to figure out how to do a pull knife or draw knife and
would welcome any input or ideas.

On Jun 25, 2:02 pm, Neillarson wrote:
On Jun 22, 4:41 pm, "trs80" wrote:



thanks. Ill see if I can get set up with the SS method. The only thing I
should need to buy is a Honing guide. The rest I should have around."trs80" wrote in message

...

is there online somewhere a good tutorial on how to sharpen and maintain
chisels and block plane knifes? Also instruction on how to restore
chisles that have really banged up edges? Im needing to use blockplane
more and should sharped the blade.

I caught the end of the program on the DIY channel where he used 4 wet
stones to sharpen a block plane knife but not the entire thing. He would
take paper thin shavings off the edge of wood after sharpened. I have a
water wheel thing with single stone wheel in water well (I guess Tormek
like) that I inherited but not sure its the right thing to use by itself
as the wet stone approach on the DIY used 4 different stones.

Id probably only need to sharpen infrequently like once every 2-3 months
as its a weekend hobby thing.
Any thoughts appreciated.

thanks- Hide quoted text -

- Show quoted text -

I am not a newbee or a oldtimer (except in age) and I have tried that
gambit, 1" belt sander (sucks), wet stones (works great if you have
the patience of a Buddist monk), Delta Wet Sharpener (hard to use, not
so hot results) SS (slow but works great) and a dedicated Wet Tool
Grinder (Tormek or Jet, mine is the the point of trying Jointer blades
(I find the cost of buying throw away planner blades outweighs the
value of sharpening them).

Here is what I am doing now:

For Chisles, Carving tools, scrapers, planes and chip breakers - I
religously use the Jet, this puts a great shallow hollow grind on
themwhich i then follow up with the SS to flatten the backs and then a
real fine grit (4000) water stone for removings the burrs. I use the
side of the Jet wet stone to flatten the scrapers.

For turning tools I use the Delta wet grinder on the dry white stone
for during the job sharpenings, periodically, I use the Jet to get
real nice clean edges on them.

I have yet to figure out how to do a pull knife or draw knife and
would welcome any input or ideas.

Heavy blades like that are easier clamped down and honed with slips.
Make your own from 400 and finer wet-dry glued around hardwood blocks.