Woodworking (rec.woodworking) Discussion forum covering all aspects of working with wood. All levels of expertise are encouraged to particiapte.

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
  #1   Report Post  
Posted to rec.woodworking
dustyone
 
Posts: n/a
Default how do I clamp this?

Hello,

I'm building a candlestick table, and I can't figure out how to glue
and clamp the legs to the center column. Any ideas? The link below is
not my table, but it'll give you the idea of what I'm dealing with.
Thanks.






http://www.custommade.com/gallery/fu...ick-table.html

  #2   Report Post  
Posted to rec.woodworking
Hambone Slim
 
Posts: n/a
Default how do I clamp this?


"dustyone" wrote...


I'm building a candlestick table, and I can't figure out how to glue
and clamp the legs to the center column.



Dovetail the tenons. No clamps required. Done correctly, no glue required.
Unless you really lick the smell of hot hide glue.


A quick & dirty way would be to make a square tenon, leave a shoulder on the
legs, and clamp with a strap clamp, then cut off the shoulders afterward.
But you'll always think less of yourself for not using the correct dovetail
tenon for the job.

8^)


Timothy Juvenal


  #3   Report Post  
Posted to rec.woodworking
bf
 
Posts: n/a
Default how do I clamp this?


dustyone wrote:
Hello,

I'm building a candlestick table, and I can't figure out how to glue
and clamp the legs to the center column. Any ideas? The link below is
not my table, but it'll give you the idea of what I'm dealing with.
Thanks.






http://www.custommade.com/gallery/fu...ick-table.html


They had a similiar table plan in Woodcraft magazine. The guy ended up
making "male" dovetails" at the end of the legs.. basically like
tenons. On the center column (which was round from being turned on a
lathe), he flattened three areas and made the female part of the
dovetail (mortise).. Therefore, he could just slide them in.

Another option would be to use a band clamp. Bessey makes a nice one,
but you'd still probably want some kind of tenon or fastener to hold
the leg in place while you're tightening the band.

  #4   Report Post  
Posted to rec.woodworking
Teamcasa
 
Posts: n/a
Default how do I clamp this?


"Hambone Slim" wrote in message
...

"dustyone" wrote...


I'm building a candlestick table, and I can't figure out how to glue
and clamp the legs to the center column.



Dovetail the tenons. No clamps required. Done correctly, no glue
required.
Unless you really lick the smell of hot hide glue.


A quick & dirty way would be to make a square tenon, leave a shoulder on
the
legs, and clamp with a strap clamp, then cut off the shoulders afterward.
But you'll always think less of yourself for not using the correct
dovetail
tenon for the job.

8^)


Timothy Juvenal

Correct however, technically they are called sliding dovetails. No clamps
required.

Dave


  #5   Report Post  
Posted to rec.woodworking
CW
 
Posts: n/a
Default how do I clamp this?

A few brads until the glue dries.

"dustyone" wrote in message
oups.com...
Hello,

I'm building a candlestick table, and I can't figure out how to glue
and clamp the legs to the center column. Any ideas? The link below is
not my table, but it'll give you the idea of what I'm dealing with.
Thanks.






http://www.custommade.com/gallery/fu...ick-table.html





  #6   Report Post  
Posted to rec.woodworking
Dave Balderstone
 
Posts: n/a
Default how do I clamp this?

In article .com,
dustyone wrote:

I'm building a candlestick table, and I can't figure out how to glue
and clamp the legs to the center column. Any ideas? The link below is
not my table, but it'll give you the idea of what I'm dealing with.
Thanks.


Why do you think you need to clamp dovetail joints?
  #7   Report Post  
Posted to rec.woodworking
Hambone Slim
 
Posts: n/a
Default how do I clamp this?




"Teamcasa" wrote...

Correct however, technically they are called sliding dovetails. No clamps
required.


I think you're right, but my brain keeps wanting to call them dovetail
tenons. I'm checking Osburns book "Measured Drawings of Early American
Furniture" - I think he shows some tables like this and lets see what he
calls the joint...

.... OK he has a drawing on page 30 of a "tripod teakettle stand" using the
joint in question...I'll check the text...

....hmmm... he doesn't say; he just calls them dovetails. He also draws a
section of the joint showing no flats on the column where the legs attach,
and the shoulders cut to match. It seems to me this would be an easier way
to get a really snug fit - by making the edges of the leg at the dovetail a
little proud, they would compress into the column and be supper snug.

Any rate, I'm sure sliding dovetail is the common modern term for the joint,
but hopefully I can be forgiven for insisting on thinking of it as a
dovetail tenon.

--
Timothy Juvenal
www.rude-tone.com/work.htm


  #8   Report Post  
Posted to rec.woodworking
Wood Butcher
 
Posts: n/a
Default how do I clamp this?

As others have responded a sliding dovetail is the traditional
method used. If you have already cut mortise & tenons or used
dowels then one way would be to clamp an auxillliary piece
of wood to one face of each leg so it extends above and below
the joint. Then use 2 band clamps, one above and one below
the joint.

Art

"dustyone" wrote in message
oups.com...
Hello,

I'm building a candlestick table, and I can't figure out how to glue
and clamp the legs to the center column. Any ideas? The link below is
not my table, but it'll give you the idea of what I'm dealing with.
Thanks.






http://www.custommade.com/gallery/fu...ick-table.html



  #9   Report Post  
Posted to rec.woodworking
dustyone
 
Posts: n/a
Default how do I clamp this?

Thank you to all.


CB

  #10   Report Post  
Posted to rec.woodworking
Phisherman
 
Posts: n/a
Default how do I clamp this?

I have made one of these. I used sliding dovetails. To make the
mortises I built a custom sled for my lathe to hold a router with a
dovetail bit. My lathe has an index pin that makes a perfect 120
degree rotation. You want a snug, but not too tight, fit. The glue
holds it together well. I did not use any clamps. Traditionally, an
underside circular metal plate with three arms would be screwed in but
that's not necessary with today's super-strong glues. BTW, if you
taper the sides of the legs you'll get a better, more delicate look. I
did my tapering on the jointer but you could use a belt sander.

On 14 Apr 2006 12:48:47 -0700, "dustyone" wrote:

Hello,

I'm building a candlestick table, and I can't figure out how to glue
and clamp the legs to the center column. Any ideas? The link below is
not my table, but it'll give you the idea of what I'm dealing with.
Thanks.






http://www.custommade.com/gallery/fu...ick-table.html

Reply
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules

Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Bessey K Body clamp problem Dick Snyder Woodworking 13 November 18th 05 05:57 PM
Supply 5,8,10 Pair Clamp Module,Orbit Clamp Module,LSA Profile-Anschlussleiste [email protected] Woodworking 0 October 28th 05 03:26 AM
Hose clamp with Torx screw frank Metalworking 9 July 17th 04 09:13 PM
A post by the rep from Adjustable Clamp Co. Woodworking 6 October 25th 03 01:06 PM


All times are GMT +1. The time now is 01:42 AM.

Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 DIYbanter.
The comments are property of their posters.
 

About Us

"It's about DIY & home improvement"