Home |
Search |
Today's Posts |
|
Woodworking (rec.woodworking) Discussion forum covering all aspects of working with wood. All levels of expertise are encouraged to particiapte. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
#1
Posted to rec.woodworking
|
|||
|
|||
INSPIRATION - Router Bit Case
http://www.gunshop.com/doubleguncase...ase_030901.jpg
These are NOT router bits. But, if you want a case for them, this is the best looking type I've seen yet. JOAT A rolling stone gathers no moss...unless it's a hobby he does on the weekends. |
#2
Posted to rec.woodworking
|
|||
|
|||
INSPIRATION - Router Bit Case
"J T" wrote in message ... http://www.gunshop.com/doubleguncase...ase_030901.jpg These are NOT router bits. But, if you want a case for them, this is the best looking type I've seen yet. Looks more like 10, 12, 16, 28, and 410 gauge. But kinda short I think. |
#3
Posted to rec.woodworking
|
|||
|
|||
INSPIRATION - Router Bit Case
In article , Leon
wrote: "J T" wrote in message ... http://www.gunshop.com/doubleguncase...ase_030901.jpg These are NOT router bits. But, if you want a case for them, this is the best looking type I've seen yet. Looks more like 10, 12, 16, 28, and 410 gauge. But kinda short I think. Snap caps. But rather fance ones, for fancy shotguns, I suppose... Kevin |
#4
Posted to rec.woodworking
|
|||
|
|||
INSPIRATION - Router Bit Case
|
#5
Posted to rec.woodworking
|
|||
|
|||
INSPIRATION - Router Bit Case
"Kevin Craig" wrote in message ... In article , Leon Snap caps. But rather fance ones, for fancy shotguns, I suppose... To protect the firing pin? or the end of the barrel? |
#6
Posted to rec.woodworking
|
|||
|
|||
INSPIRATION - Router Bit Case
The former. Snap caps go in the chamber in place of a shell or
cartridge. They usually have a small spring under a brass cap where the primer would be in a normal cartridge. That way the firing pin will strike a point that "gives" when struck, while still providing enough resistance so that the rear of the firing pin does not contact the rear of the frame, possibly causing damage to one or the other. With many of the fine old English guns the hammer spring is actually rather weak and can take a "set" if the weapon is left cocked while in storage. To avoid this the trigger is pulled to release the spring tension prior to putting the gun away. As to cost, depending on grade and condition, a 5 gauge set of matched Purdeys could be worth as much as a medium sized house in Dallas (say 150K), at the low end, only as much as a good truck. I have a Purdey (standard grade 12 gauge (2 1/2" shells)) that belonged to my father, picked up in London during WWII, that I have been offered a bunch of bucks for. It is truly a work of art even in standard grade. Regards. On Fri, 09 Dec 2005 14:44:55 GMT, "Leon" wrote: To protect the firing pin? or the end of the barrel? |
#7
Posted to rec.woodworking
|
|||
|
|||
INSPIRATION - Router Bit Case
Kind of limiting ain't it. Them router bits breed like
rabbits. If you don't keep them separated you'll be up to your ass in them within a month. I'm working on keeping mine on separate shelves, in a closed wall cabinet so they don't sneak off and copulate under the router table or in my wood stach. Haven't got the knife hinges installed right yet but I'm hoping too before the router bit population fills the shop http://home.comcast.net/~charliebcz/...redDoors0.html charlie b |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Where to position router plate | Woodworking | |||
INSPIRATION - GUN CASE | Woodworking | |||
2-1/4 or 3 HP router for floating tenons and dovetail jig? | Woodworking | |||
Plunge or non-plunge router better under table? | Woodworking | |||
Router Table Top Questions | Woodworking |