Home |
Search |
Today's Posts |
|
Woodworking (rec.woodworking) Discussion forum covering all aspects of working with wood. All levels of expertise are encouraged to particiapte. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
#1
|
|||
|
|||
Cuttlefish bone for casting ?
I want to do some bronze casting, using the cuttlefish bone moulding
process - a mould is carved or pressed directly into the cuttlefish. I have my cuttles. Now I need to machine them a little to make flat surfaces, interlocking keys etc. Any advice ? Can I machine cuttlefish bone as I would timber ? Is the dust a hazard to me, or my machinery ? Will it shatter if I go at it with power tools? How should I machine it ? What's the best bit of bone to use? Do I need mortice and tenon keyways in it, and if so, how do I form them? Thanks for any advice you can offer. |
#2
|
|||
|
|||
Andy Dingley wrote:
I want to do some bronze casting, using the cuttlefish bone moulding process - a mould is carved or pressed directly into the cuttlefish. I have my cuttles. Now I need to machine them a little to make flat surfaces, interlocking keys etc. Any advice ? Can I machine cuttlefish bone as I would timber ? Is the dust a hazard to me, or my machinery ? Will it shatter if I go at it with power tools? How should I machine it ? What's the best bit of bone to use? Do I need mortice and tenon keyways in it, and if so, how do I form them? Thanks for any advice you can offer. Use the soft side, almost like styrofoam. I used to flatten mine on a concrete block, squeeze them together over the original object and notch or mark the mating spots. Take them apart, remove the object and cut a sprue notch on one end (of both), then re position them together and wire together. You can cut it with a knife on the soft side. Once upon a time I lived on the beach in Sicily and would pick them up in my backyard. This is rather crude casting but fun. -- Gerald Ross Cochran, GA D.A.M. -- Mothers Against Dyslexia ----== Posted via Newsfeeds.Com - Unlimited-Uncensored-Secure Usenet News==---- http://www.newsfeeds.com The #1 Newsgroup Service in the World! 120,000+ Newsgroups ----= East and West-Coast Server Farms - Total Privacy via Encryption =---- |
#3
|
|||
|
|||
Can I machine cuttlefish bone as I would timber ? Is the dust a hazard
to me, or my machinery ? Will it shatter if I go at it with power tools? I used to use a parrot to machine them. He was slow but steady. |
#4
|
|||
|
|||
There is a rec.crafts.metalworking newsgroup where they may have some experience and be familiar with the hazards. -- FF |
#5
|
|||
|
|||
Andy Dingley wrote: I want to do some bronze casting, using the cuttlefish bone moulding process - a mould is carved or pressed directly into the cuttlefish. it leaves a surface a lot like wood grain. I kind of like the effect, and the bit of cuttlebone casting I did I brushed out the grain to accentuate it. you can work to minimize it, burnishing to fill the grain, but if smooth is what you're after, there are refractory casting materials specific for the purpose. I have my cuttles. Now I need to machine them a little to make flat surfaces, interlocking keys etc. Any advice ? the rubbing on a brick is a good technique for getting a flat face. Can I machine cuttlefish bone as I would timber ? pretty much. Is the dust a hazard to me, or my machinery ? I wouldn't go snorting the dust, but in small quantities I don't imagine handling it would be a hazard. Will it shatter if I go at it with power tools? power tools should be unnecessary. it's soft and pretty porous. damn near scoop it out with a spoon. How should I machine it ? hand tools..... What's the best bit of bone to use? right up the middle. Do I need mortice and tenon keyways in it, and if so, how do I form them? if you need to register the halves, a groove in the edge where the binding wire bites in should be plenty. if you want a flat back, save the cost of cuttlebone and use something cheaper and easier to get flat for the back. a fire brick or shard of kiln shelf works well. I have used wood with good results for small castings. Thanks for any advice you can offer. have fun. |
#6
|
|||
|
|||
The smell is going to astound you!
|
#7
|
|||
|
|||
In article .com,
wrote: There is a rec.crafts.metalworking newsgroup where they may have some experience and be familiar with the hazards. He has it already cross-posted to rec.crafts.metalworking, so we are already seeing it. Not that I know the answers, but someone else probably does. Enjoy, DoN. -- Email: | Voice (all times): (703) 938-4564 (too) near Washington D.C. | http://www.d-and-d.com/dnichols/DoN.html --- Black Holes are where God is dividing by zero --- |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Cuttlefish bone for casting ? | Metalworking | |||
Turning Bone - my observations | Woodturning | |||
Computer Bone paint | Electronics Repair | |||
Mini Review: Forrest WoodWorker II Blade Lacerates Arm to Bone | Woodworking |