Dear All,

I am searching for a fastener that will temporally connect two
horizontal boards.

The fastener needs to be contained within the edge of the boards only
and not visable when assembled.

It needs to be temporally as it needs to be removed occationally.

It is a bit like the KLIX DOUBLE DOWEL and associated KLIX CAM fittings
that can be found on www.woodfit.com (At the time of posting their
webiste is not working, hence no link provided)

But obviously the CAM is visable, this is unacceptable.

What I have in mind is somthing like the KLIC DOUBLE DOWEL but with a
ball bearing housing (the CAM) that is embedded in the edge of the
wood, hence not visable) and captures the end of the KLIX DOWEL when
inserted but releases it (after pulling it).

Basically I want a device that acts like a wooden DOWEL (unglued) would
when connecting the edges of two horizontal boards. However, fastens
the boards together until they need to be seperated, unlike an unglued
dowel.

I give the example of a dowel as it is unseen when assembled.

If anyone has come across such as fastener then please let me know, or
if I need to provide more information please contact me.

Regards

Simon

A simple solution is to make some shallow holes that are aligned in the two
pieces and glue in magnets, so they have N pole exposed in one board and S
pole in the other. They will attract strongly when in contact, but will
come apart when pulled. Depending on the dimensions and weight of the
boards, you probably want several magnet pairs at intervals.

Steve

"stockton" wrote in message
oups.com...
Dear All,

I am searching for a fastener that will temporally connect two
horizontal boards.

The fastener needs to be contained within the edge of the boards only
and not visable when assembled.

It needs to be temporally as it needs to be removed occationally.

It is a bit like the KLIX DOUBLE DOWEL and associated KLIX CAM fittings
that can be found on www.woodfit.com (At the time of posting their
webiste is not working, hence no link provided)

But obviously the CAM is visable, this is unacceptable.

What I have in mind is somthing like the KLIC DOUBLE DOWEL but with a
ball bearing housing (the CAM) that is embedded in the edge of the
wood, hence not visable) and captures the end of the KLIX DOWEL when
inserted but releases it (after pulling it).

Basically I want a device that acts like a wooden DOWEL (unglued) would
when connecting the edges of two horizontal boards. However, fastens
the boards together until they need to be seperated, unlike an unglued
dowel.

I give the example of a dowel as it is unseen when assembled.

If anyone has come across such as fastener then please let me know, or
if I need to provide more information please contact me.

Regards

Simon

Thanks for your responces, I have looked at what you suggest but I have
further spanners to throw into the works.

1) I have to remove the joint at 90 degrees to the edge of the boards
so sliding it is not an option.

2) Nothing must protrude from the edge of the boards (both of them)

I like the idea of magnets, but I don't think that the attraction
between them will be sufficent.

It is not the force at 90 degrees to the edge of the boards but in the
other direction (ie. aligned with the connection is not as crutial and
the force aligned with the edge of the boards.)

Thanks for your responces so far.

If you have any more ideas please let me know.

Simon

Maybe we need better specs to evaluate the problem and suggest solutions.

If you use rare earth magnets and put enough of them in, you won't be able
to get the "joint" apart by pulling.

Steve

"stockton" wrote in message
oups.com...
Thanks for your responces, I have looked at what you suggest but I have
further spanners to throw into the works.

1) I have to remove the joint at 90 degrees to the edge of the boards
so sliding it is not an option.

2) Nothing must protrude from the edge of the boards (both of them)

I like the idea of magnets, but I don't think that the attraction
between them will be sufficent.

It is not the force at 90 degrees to the edge of the boards but in the
other direction (ie. aligned with the connection is not as crutial and
the force aligned with the edge of the boards.)

Thanks for your responces so far.

If you have any more ideas please let me know.

Simon

On Sun 22 May 2005 04:44:22p, "stockton"
wrote in oups.com:

2) Nothing must protrude from the edge of the boards (both of them)

Outside of magnets, I can't think of any way one can keep this
specification. If nothing can protrude from either edge, and you can't use
glue, and you can't put anything on the outside of the boards, there just
isn't any way you can tell those two boards they're supposed to be
partners.

Oh, wait a minute. Can you have a screwtop flush on one edge of either
board? This cheap computer desk I'm using has something like that. One side
has a metal fastener that accepts a hook, and the other side has a hook
that turns with that flushmounted screw mechanism. Put a screwdriver in it,
turn the hook, the boards come apart. Put them together, turn the hook the
other way, it goes into the mounting on the other side.

But this desk is the only thing I've ever seen with that mechanism and I've
never seen it in any of the hardware sites. I don't even know what it's
called. Hell, I'm probably describing it all wrong besides.