Home |
Search |
Today's Posts |
|
Woodturning (rec.crafts.woodturning) To discuss tools, techniques, styles, materials, shows and competitions, education and educational materials related to woodturning. All skill levels are welcome, from art turners to production turners, beginners to masters. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
#1
Posted to rec.crafts.woodturning
|
|||
|
|||
Cutting logs
We were cutting a 10 dia. log in 4" slices for bowls on a band saw.
Worked great until the last cut. i.e. grip wasn't quite the same being close to the 1 1/2" blade is a bit intimidating. The wood spun and the blade is bend, thankfully no one was injured. Now it's time to do it the safe way. Does anyone have a jig to handle this type of sawing AND a jig for resawing. Ron |
#2
Posted to rec.crafts.woodturning
|
|||
|
|||
Cutting logs
Ron wrote:
We were cutting a 10 dia. log in 4" slices for bowls on a band saw. Worked great until the last cut. i.e. grip wasn't quite the same being close to the 1 1/2" blade is a bit intimidating. The wood spun and the blade is bend, thankfully no one was injured. Now it's time to do it the safe way. Does anyone have a jig to handle this type of sawing AND a jig for resawing. Ron From the sound of it, you were cutting into the bark side and the log rolled. If so, all you need is an L shaped jig. Clamp the log to the jig. Cut. Move the log and reclamp. cut ... What you Must prevent is any rolling motion of the log. It is almost impossible to do this by hand. For resawing, google "resaw technique". Lots of helpful articles out there. |
#3
Posted to rec.crafts.woodturning
|
|||
|
|||
Cutting logs
As Lobby said, it sounds like you were cutting from the bark to the center
of the log so as to turn end grain bowls. What you need is something to prevent the log from rolling. I use a c clamp that rests the arm on the band saw table and prevents rolling. For a 10" diameter log I think a bar clamp might be more appropriate. -- God bless and safe turning Darrell Feltmate Truro, NS Canada |
#4
Posted to rec.crafts.woodturning
|
|||
|
|||
Cutting logs
"Ron" wrote in message ... We were cutting a 10 dia. log in 4" slices for bowls on a band saw. Worked great until the last cut. i.e. grip wasn't quite the same being close to the 1 1/2" blade is a bit intimidating. The wood spun and the blade is bend, thankfully no one was injured. Now it's time to do it the safe way. Does anyone have a jig to handle this type of sawing AND a jig for resawing. Sounds like crosscutting rather than ripping. No matter. Answer's the same. 1) Use the chainsaw, you don't need precision here, so why heft and huff. 2) If you insist on ruining your driveby gloat of a humongous bandsaw to cut through sand-loaded bark (clean it), get a flat spot to rest the log on on. Can be as simple as a V block or two parallel 1x1s screwed to the main. Careful of the screw placement, of course. 3) Full-footprint jig for crosscutting features the blocks attached to something guided by a bar in the miter gage groove or edge. Bungee will help keep your hand away. For ripping operations, numbers one and two are still good. The preferred jig featured dogs like the commercial outfits and a sled that rides the miter groove. Commercial jobs and pictures at Woodcraft, make yours similar. Mine had pipe clamps instead of pinch dogs. Of course back then I had it attached to a 24" three horse Powermatic - I can gloat too - which, unfortunately was not mine. The Bandsaw Book by Mark Duginskie for the best resaw and circle jigs. |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
cutting board | Woodworking | |||
Painting a room...cutting in | UK diy | |||
Robert H. Peterson Gas Logs | Home Repair | |||
Basics on Depth of Cuts | Metalworking | |||
gas or not? | Metalworking |