I`m replacing a shower enclosure and tiles built into a corner of a
plasterboard stud wall ensuite

The previous enclosure + tiles looks as though they weren`t 100% waterproof so
I`m contemplating fitting Wickes Aquapanels which are supposedly the waterproof
method of doing it (They are also currently at a reduced price)

The shower is a hot+cold and not a mains electric so the pipework will be
fitted through the new panel.

Any tips, advice or suggestions to using fitting these panels in order to make
a waterproof job?

Any other alternative methods?

Thanks

Chas

"Restoredclassic" wrote in message
...
I`m replacing a shower enclosure and tiles built into a corner of a
plasterboard stud wall ensuite

The previous enclosure + tiles looks as though they weren`t 100%
waterproof so
I`m contemplating fitting Wickes Aquapanels which are supposedly the
waterproof
method of doing it (They are also currently at a reduced price)

The shower is a hot+cold and not a mains electric so the pipework will be
fitted through the new panel.

Any tips, advice or suggestions to using fitting these panels in order to
make
a waterproof job?

Any other alternative methods?

Chas, good stuff. Just stick to the makers instructions. Tiles can be put
directly onto it.



_________________________________________
Usenet Zone Free Binaries Usenet Server
More than 120,000 groups
Unlimited download
http://www.usenetzone.com to open account

Doctor Evil wrote:
"Restoredclassic" wrote in message
...

I`m replacing a shower enclosure and tiles built into a corner of
a plasterboard stud wall ensuite

The previous enclosure + tiles looks as though they weren`t 100%
waterproof so I`m contemplating fitting Wickes Aquapanels which are
supposedly the waterproof method of doing it (They are also
currently at a reduced price) The shower is a hot+cold and not a
mains electric so the pipework will be fitted through the new
panel.

Any tips, advice or suggestions to using fitting these panels in
order to make a waterproof job?


Chas, good stuff. Just stick to the makers instructions. Tiles can
be put directly onto it.

I agree with Dr E (did I really just type that??). Aquapanel is the
mutt's nuts for shower enclosures.

There's a Wickes 'how-to-do-it' leaflet available in store or on their
website:
http://media.venda.com/wickes/ebiz/w...ges/gil/54.pdf (I think you
need to register for the link to work), also ISTR that the Knauf (ie the
manufacturer) website has info about it too. Also google the archives
of this newsgroup for "aquapanel" - it comes up regularly.

David

The previous enclosure + tiles looks as though they weren`t 100%
waterproof so I`m contemplating fitting Wickes Aquapanels which are
supposedly the waterproof method of doing it (They are also
currently at a reduced price) The shower is a hot+cold and not a
mains electric so the pipework will be fitted through the new panel.

Any tips, advice or suggestions to using fitting these panels in
order to make a waterproof job?

It is not waterproof, it is water-resistant. I.e. if it gets wet, it
won't fall apart, but it is not a barrier to the water seeping through
the wall. To get waterproof, you need to use wedi board or the
equivalent, or ply/aquapanel/whatever with and tank it using somehting
like BAL WP1. Having just done a big walk-in shower with wediboard, I
think next time I would use the Wedi Fundo shower base, but just use ply
on the walls and tank it. Wedi board is twice as expensive as ply,
and then you need to buy a tanking kit anyway to seal the joins (they do
their own tape, but at such a stupid price.

Or, carry on as you are, which is what any professional tiler would do.
As long as you get a proper solid bed (you can buy special non-notched
trowels for this apparently, they just have a "prong" at each end to set
the depth of the bed) and use a waterproof adhesive then it should in
theory be waterproof.

In terms of waterproofing the pipe penetrations, the fittings usually
come with rubber gaskets to seal against the tiles, which you could
supplement with silicone if you're feeling paranoid. Keep the controls
out of direct spray and they'll be OK. For the outlet you can drill a
fairly precise hole around the female iron coupler and seal the gap with
silicone. The outlet that screws into that should have a gasket of some
sort anyway.

Jake

Restoredclassic wrote :-

I`m replacing a shower enclosure and tiles built into a corner of a
plasterboard stud wall ensuite

The previous enclosure + tiles looks as though they weren`t 100%
waterproof so
I`m contemplating fitting Wickes Aquapanels which are supposedly the
waterproof
method of doing it (They are also currently at a reduced price)

The shower is a hot+cold and not a mains electric so the pipework will be
fitted through the new panel.

Any tips, advice or suggestions to using fitting these panels in order to
make
a waterproof job?

Any other alternative methods?

Thanks

Chas

Good stuff, built a shower 2 yrs ago in the corner and built a stud wall,
and used aquapanel instead of plaster board, very substantial and just tile
straight on top (keep rough side as face)

Regards Jeff

http://www.jameshardieeu.com/features.html

hardibacker is an alternative that i can recommend,used it for my shower
enclosure walls,works well,it may be cheaper than aquapanel.size is 1500 x
900 x6 and 1200x 800x12