I've got a Combi boiler system, three of my rads have no thermostat
fixed and I want to fix one to two of them.

Do I have to drain the entire system to do so of is there a way round
this.

Geoff Lane

In an earlier contribution to this discussion,
Geoff Lane wrote:

I've got a Combi boiler system, three of my rads have no thermostat
fixed and I want to fix one to two of them.

Do I have to drain the entire system to do so of is there a way round
this.

Geoff Lane

You'll have to at least partially drain it - and obviously the rads
themselves.

Start with one of the rads. If there's a drain cock in the pipe next to one
of the valves, use that - with the valve open - to drain the rad and pipe in
one go. If there isn't, it gets a bit messier. Priceed as follows:

Turn off both valves tightly. Partially undo one of the unions between rad
and valve, and collect the water from the rad in a container. Undo the bleed
screw on the rad.[Use lots of old towels to protect any carpets from foul
black staining liquid.]

When the rad is empty, fully undo the union plus the one the other end - and
lift the rad off its brackets. [While it's off, take it outside and give it
a good wash out with a hosepipe].

At this stage, the pipework is still full of water - only the rad is empty.
Decide which valve you're going to replace with a TRV. Drain down the
pipework feeding that valve into a container by opening the valve. When no
nore water comes out you can remove the valve from the pipe and fit the TRV
instead.

Swap the tail in the radiator with the one which came with the TRV. [This is
most easily done with the rad lying down on a Workmate or similar]. You can
then re-hang the radiator and connect the valves to the tails.

Then do it all over again with the next rad!
--
Cheers,
Set Square
______
Please reply to newsgroup. Reply address is invalid.

In article ,
Geoff Lane wrote:
I've got a Combi boiler system, three of my rads have no thermostat
fixed and I want to fix one to two of them.

Do I have to drain the entire system to do so of is there a way round
this.

Unless it's been done recently, it's no bad thing to drain down, flush
through until the water runs clear and re-fill with fresh inhibitor.

The other way is to freeze the pipes, but this is an expensive option.

--
*Fax is stronger than fiction *

Dave Plowman London SW
To e-mail, change noise into sound.

On Wed, 26 Jan 2005 21:26:52 -0000, "Set Square"
wrote:

I've got a Combi boiler system, three of my rads have no thermostat
fixed and I want to fix one to two of them.

Do I have to drain the entire system to do so of is there a way round
this.

Geoff Lane

You'll have to at least partially drain it - and obviously the rads
themselves.

Start with one of the rads. If there's a drain cock in the pipe next to one
of the valves, use that - with the valve open - to drain the rad and pipe in
one go. If there isn't, it gets a bit messier. Priceed as follows:

Snipped

Thanks for very in depth reply; I've fitted a rad with thermostat
before but some years back and forgot the procedure.

One will definitely be a new rad as well.

Geoff Lane

On Wed, 26 Jan 2005 22:07:43 +0000 (GMT), "Dave Plowman (News)"
wrote:

In article ,
Geoff Lane wrote:
I've got a Combi boiler system, three of my rads have no thermostat
fixed and I want to fix one to two of them.

Do I have to drain the entire system to do so of is there a way round
this.

Unless it's been done recently, it's no bad thing to drain down, flush
through until the water runs clear and re-fill with fresh inhibitor.

The other way is to freeze the pipes, but this is an expensive option.

Forgot about that one but pound to a penny something wouldn't go
smoothly and it'd thaw out anyway :-)))

Geoff Lane