Home |
Search |
Today's Posts |
|
UK diy (uk.d-i-y) For the discussion of all topics related to diy (do-it-yourself) in the UK. All levels of experience and proficency are welcome to join in to ask questions or offer solutions. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
#1
Posted to uk.d-i-y
|
|||
|
|||
Thermlite wall - guide for max load (radiator)
Whilst someone has mentioned these horrible things, I have to specify a
radiator to hang off one: Wall does have an advantage - dog legs: | | ====| RRR | | ========= RRR is the rad. Wall is 2.4m high, stops at the ceiling (and is not connected to anything above except by virtue of being a tight fit to the plasterboard). Is there a rule of thumb for how heavy and how high a load may go? If the wall were not crap I would put in an 1800mm high vertical rad. But the top fixings would be on the 2nd course and I don't trust that not to pull the top over. Hence the question |
#2
Posted to uk.d-i-y
|
|||
|
|||
Thermlite wall - guide for max load (radiator)
On 27/09/2017 16:44, Tim Watts wrote:
Whilst someone has mentioned these horrible things, I have to specify a radiator to hang off one: Wall does have an advantage - dog legs: Â*Â*Â* | Â*Â*Â* | Â*Â*Â* ====| Â*Â*Â* RRR | Â*Â*Â*Â*Â*Â*Â* | Â*Â*Â*Â*Â*Â*Â* ========= RRR is the rad. Wall is 2.4m high, stops at the ceiling (and is not connected to anything above except by virtue of being a tight fit to the plasterboard). Is there a rule of thumb for how heavy and how high a load may go? If the wall were not crap I would put in an 1800mm high vertical rad. But the top fixings would be on the 2nd course and I don't trust that not to pull the top over. Hence the question There's not very much "moment" even with a heavy radiator (as long as someone does not try to climb it like a ladder). I think you are worrying unnecessarily, especially with your dog-leg (provided the blocks are properly laid to key the walls together). It is probably worth using a reasonably long fittings. I've never used Multi Monti's in lightweight blocks, but they might work well, perhaps using a drill 1/2 mm smaller than you would use with normal blocks or bricks. |
#3
Posted to uk.d-i-y
|
|||
|
|||
Thermlite wall - guide for max load (radiator)
On 27/09/17 20:26, newshound wrote:
Hiya, There's not very much "moment" even with a heavy radiator (as long as someone does not try to climb it like a ladder). I always like to factor a little abuse in (visiting little kid, someone hanging heavy wet coats on it etc) I think you are worrying unnecessarily, especially with your dog-leg (provided the blocks are properly laid to key the walls together). Can confirm that: https://drive.google.com/open?id=0Bx...HRpdElJeG1Lc3c That's properly coursed around the corners. It is probably worth using a reasonably long fittings. I've never used Multi Monti's in lightweight blocks, but they might work well, perhaps using a drill 1/2 mm smaller than you would use with normal blocks or bricks. That much I do have an answer to (having fixed to the other side of this for bog cistern and free hanging basin): I'll either use resin fixings 3/4 the way through the wall or these bad boys: http://buyrigifixonline.co.uk/ (which I have used before). The wall will come down before they let go! I guess you're right - it's just before that wall was plastered, I chased it for conduit and the top block jumped off its mortar, so my confidence went through the floor. I'll probably aim for 3rd course from top - there's a lot of interlocking at that stage. Thanks mate! |
#4
Posted to uk.d-i-y
|
|||
|
|||
Thermlite wall - guide for max load (radiator)
On 27/09/17 20:26, newshound wrote:
There's not very much "moment" even with a heavy radiator (as long as someone does not try to climb it like a ladder). I think you are worrying unnecessarily, especially with your dog-leg (provided the blocks are properly laid to key the walls together). It is probably worth using a reasonably long fittings. I've never used Multi Monti's in lightweight blocks, but they might work well, perhaps using a drill 1/2 mm smaller than you would use with normal blocks or bricks. I was worried as you hear the odd story of gable end walls falling over after someone hung a boiler on the inside, or occasionally due to very high winds... |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Does Max mean max signal or max attenuation? | Electronics Repair | |||
3ds max 4 crack | 3ds max 4 cracks | 3ds max 4 error 6033 | Woodworking | |||
Speed Rack max load | Metalworking | |||
max international, mlm business opportunity, MaxGXL, networkmarketing opportunity , Max GXL, MaxWLX, Max N-fuze, Max WLX, | Home Ownership | |||
How to calculate max load | Woodworking |