Home |
Search |
Today's Posts |
|
Metalworking (rec.crafts.metalworking) Discuss various aspects of working with metal, such as machining, welding, metal joining, screwing, casting, hardening/tempering, blacksmithing/forging, spinning and hammer work, sheet metal work. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
#1
|
|||
|
|||
Pictures of the INSTALLED Curtis compressor
Subject: Pictures of the INSTALLED Curtis compressor
Newsgroup: alt.home.repair = Ignoramus18224 = wrote: http://igor.chudov.com/ How do you have access to that site? -- -Graham Remove the snails to email |
#2
|
|||
|
|||
Looks nice! I would install the belt guard and use some rubber mounting of
some type to dampen the vibration. I wouldn't be woried about getting my body parts into it so much as Murphey slipping the odd piece off the wall and sliding into the belts and doing the things that MS Murphey does best Glenn "Ignoramus18224" wrote in message ... I installed the curtis compressor today. It is where it is supposed to be, wired the way I intended, etc. The only work to be done is adding an auto drain and properly attaching a pressure regulator that was included in the sale. http://igor.chudov.com/projects/CurtisCompressor/ I reorganized the album, now there is a new page with installation pictures. That page explains what I have done, in some detail. There are two new circuits, one for 110v outlets behind the compressor (for auto drain etc), and another is a dedicated 220V circuit for the compressor. Wires for them are enclosed in 3/4" EMT. The mess in the garage is temporary, it is in fact organized enough to allow two vehicles to be parked. i |
#3
|
|||
|
|||
G. Morgan wrote:
How do you have access to that site? The domain likely belongs to the OP. |
#4
|
|||
|
|||
Iggy
I set my compressor on a double layer of old carpet padding and it really cut the noise transfer down. I also would think about putting a strain relief on the Bx where it lands on the machine. The full weight of it is pulling at right angle to your pipe nipple and it may in time snap it. Great looking install though. Keep in mind as you connect the piping system to it to use a hose between the compressor and the wall. lg no neat sig line "Glenn" wrote in message ... Looks nice! I would install the belt guard and use some rubber mounting of some type to dampen the vibration. I wouldn't be woried about getting my body parts into it so much as Murphey slipping the odd piece off the wall and sliding into the belts and doing the things that MS Murphey does best Glenn |
#5
|
|||
|
|||
On Sun, 27 Feb 2005 00:49:29 -0600, the inscrutable G. Morgan
spake: Subject: Pictures of the INSTALLED Curtis compressor Newsgroup: alt.home.repair = Ignoramus18224 = wrote: http://igor.chudov.com/ How do you have access to that site? How do YOU get access? Click on the door below the funky eyes. -- "Menja bé, caga fort!" |
#6
|
|||
|
|||
I also would think about putting a strain relief on the Bx where it lands on the machine. The full weight of it is pulling at right angle to your pipe nipple and it may in time snap it. I am sorry, I have no idea what you are talking about!!! (due to my ignorance of compressors) The Bx cable is the shielded power cable that runs from the wall to the pressure switch and supplies power to the machine. It looks like the angle that it enters puts a strain on the switch and it may break the pipe nipple 'tween the tank and pressure switch. I think that I would clamp the cable to the motor mount plate so that no pull is put on the pressure switch. lg no neat sig line |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Bought a used Curtis 80 gal compressor... | Metalworking | |||
Curtis 80 gal 3hp compressor | Metalworking | |||
Sears air compressor starting problem | Woodworking | |||
Sears air compressor starting problem | Home Repair | |||
Sears air compressor starting problem | Home Ownership |