Reorganizing a shop recently bought up questions concerning how to get
more efficient storage around a bench top horizontal mill, in this
case a Burke #4 horizontal mill. Any number of similar benchtop mills,
both horizontal and vertical, could benefit from this.

This mill sometimes can be found on top of a massive cast iron
pedestal. While this arrangement serves well for rigidity, it offers
absolutely no opportunity for any storage for any of the needed
tooling that a horizontal mill needs to do its job.

I would be interested in hearing what and how other HSMers have done
to provide efficient storage for all those arbors, index heads,
collets, end mill holders, etc. that are used. I would also like to
hear from anyone who has incorporated this storage in a cabinet or
stand that also allows for the horizontal mill itself to sit on.

Thanks in advance,

TMT

"Too_Many_Tools" wrote in message
om...
Reorganizing a shop recently bought up questions concerning how to get
more efficient storage around a bench top horizontal mill, in this
case a Burke #4 horizontal mill. Any number of similar benchtop mills,
both horizontal and vertical, could benefit from this.

I would be interested in hearing what and how other HSMers have done
to provide efficient storage for all those arbors, index heads,
collets, end mill holders, etc. that are used. I would also like to
hear from anyone who has incorporated this storage in a cabinet or
stand that also allows for the horizontal mill itself to sit on.

My #4 Burke came with a stand. However, you may be interested in what I
did for storage. I didn't like the little compartment in the stand itself.
It isn't very convenient -- dark, coolant drips, etc. I think that its only
proper use (once I get around to it) is to house a coolant system. Okay,
now for the storage problem.
I looked around at thrift shops until I found an old metal desk.
You know the type. Three regular drawers on one side and a single drawer
plus file drawer on the other side -- also a middle drawer, but you will
lose that feature. They also have a lineoleum top -- which you will want to
remove. The best ones are those made during or shortly after WWII, because
they are of the heaviest gauge steel. The desk WILL NOT be used as a
stand -- this is for guys who have a #4 with a stand or a willing to make a
heavy enough stand.
Cut a hole in the center of the desk wide enough for the stand to
poke through. With the casters removed from the desk, the coolant pan will
just sit on the desk top with a fraction of an inch to spare. You don't
want actual contact. You now can reassemble the mill on top of the desk.
You know those wings that the desks have? Sheet metal. Use a hole punch to
cut out a bunch of holes for collets, mill holders, chucks, etc. You can
still put rarely used stuff in that drawer. The big file drawer is good for
storing big items like a rotary table, vertical head, etc.
I found out, soon enough, that even this isn't nearly enough for the
huge amount of tooling one tends to accumulate. Two wall mounted cabinets
and an on-sale Sears rolling cabinet finished off the storage problem.

Boris

--

-------------------------------------
Boris Beizer Ph.D. Seminars and Consulting
1232 Glenbrook Road on Software Testing and
Huntingdon Valley, PA 19006 Quality Assurance

TEL: 215-572-5580
FAX: 215-886-0144
Email bsquare "at" sprintmail.com

------------------------------------------

In article ,
Too_Many_Tools wrote:
Reorganizing a shop recently bought up questions concerning how to get
more efficient storage around a bench top horizontal mill, in this
case a Burke #4 horizontal mill. Any number of similar benchtop mills,
both horizontal and vertical, could benefit from this.

[ ... ]

I would be interested in hearing what and how other HSMers have done
to provide efficient storage for all those arbors, index heads,
collets, end mill holders, etc. that are used. I would also like to
hear from anyone who has incorporated this storage in a cabinet or
stand that also allows for the horizontal mill itself to sit on.

Well ... mine is not quite that small. It is a Nichols
horizontal mill, and comes with its own base as part of it (not bolted
together, but a part of the casting). Of course, it provides no storage
for tooling.

I happen to have it beside a bench which has a DiAcro 24" finger
brake mounted facing away from it.

So -- for most of the time, there are two of the fiberglass
storage racks for 40-taper tooling. This holds some of the sorter tools
closer to the back of the brake (except when I am using it), and some of
the longer items (including arbors) on the side away from the brake.

If I have to use the brake, I have to move the two racks, but
the rest of the time, it is a big help.

The wrenches need to be balanced nearby, with no real place to
properly hang them.

Good Luck,
DoN.

--
Email: | Voice (all times): (703) 938-4564
(too) near Washington D.C. | http://www.d-and-d.com/dnichols/DoN.html
--- Black Holes are where God is dividing by zero ---