Home |
Search |
Today's Posts |
|
Metalworking (rec.crafts.metalworking) Discuss various aspects of working with metal, such as machining, welding, metal joining, screwing, casting, hardening/tempering, blacksmithing/forging, spinning and hammer work, sheet metal work. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
#1
Posted to rec.crafts.metalworking
|
|||
|
|||
Three phase load, wye vs delta
Just for the kicks, I wanted to make a 60 kw load bank to test the
generator. I have three 20 kW electric heat strip elements. I wanted to connect them in a delta connection. This way, as I believe, I can get 60 kW out of the three phase generator (except that it is not capable of making 240v, only about 216, so it will be a little less than 60 kW). With a single phase connection (for my home generator), using only two terminals out of three, I would get 20 kW. Am I missing anything here? For a three phase connection, does it matter if the generator is wye or delta wound? i |
#2
Posted to rec.crafts.metalworking
|
|||
|
|||
Three phase load, wye vs delta
Cross-Slide wrote:
On Jan 28, 5:01 pm, Ignoramus30636ignoramus30...@NOSPAM. 30636.invalid wrote: Just for the kicks, I wanted to make a 60 kw load bank to test the generator. I have three 20 kW electric heat strip elements. I wanted to connect them in a delta connection. This way, as I believe, I can get 60 kW out of the three phase generator (except that it is not capable of making 240v, only about 216, so it will be a little less than 60 kW). With a single phase connection (for my home generator), using only two terminals out of three, I would get 20 kW. Am I missing anything here? For a three phase connection, does it matter if the generator is wye or delta wound? i Delta or Wye on the generator, will affect the voltage it can develop. I disagree that you can't connect a Wye load to a Delta source. Why not? The Wye Load will still consume power, even if the center neutral is not connected. You can connect a delta to a Y load if the legs of the load are balanced as in Iggy's case. If the loads are unbalancd you will have unbalanced voltages in the legs and if the unbalance is large you will probably do damage because of excess voltage in one of the legs. John Another thing about generators I found out.... I was initially skeptical that is was possible to get single phase from a three phase generator since there HAD to be three pole sets... Then DOOOHHHH ! you can re-group the twelve coils sets into four groups of three, for single phase, or three groups of four for three phase. Hopefully that gives a few ideas... |
#3
Posted to rec.crafts.metalworking
|
|||
|
|||
Three phase load, wye vs delta
On Jan 29, 12:48*pm, john wrote:
Cross-Slide wrote: On Jan 28, 5:01 pm, Ignoramus30636ignoramus30...@NOSPAM. 30636.invalid *wrote: Just for the kicks, I wanted to make a 60 kw load bank to test the generator. I have three 20 kW electric heat strip elements. I wanted to connect them in a delta connection. This way, as I believe, I can get 60 kW out of the three phase generator (except that it is not capable of making 240v, only about 216, so it will be a little less than 60 kW). With a single phase connection (for my home generator), using only two terminals out of three, I would get 20 kW. Am I missing anything here? For a three phase connection, does it matter if the generator is wye or delta wound? i Delta or Wye on the generator, will affect the voltage it can develop. I disagree that you can't connect a Wye load to a Delta source. Why not? The Wye Load will still consume power, even if the center neutral is not connected. You can connect a delta to a Y load if the legs of the load are balanced as in Iggy's case. *If the loads are unbalancd you will have unbalanced voltages in the legs and if the unbalance is large you will probably do damage because of excess voltage in one of the legs. John John, you are Absolutely correct! I assumed that, but did not think to mention it. |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
FS: Delta Unisaw, single phase, Chicagoland, $1200 | Woodworking | |||
Three phase for a resistance load?? | Home Repair | |||
change 3 phase to 1 phase on delta jointer | Woodworking | |||
Variable load for testing phase convertor | Metalworking | |||
Circuit Breaker Size? - 25HP, 200V, 3-Phase, 70A (Full Load) | Metalworking |