On Sep 14, 2:39*pm, Gunner Asch wrote:
Im getting ready to replace the bearings in my Hardinge HLV-H threading
gearbox and am having a bit of a difficulty finding "3200" bearings
online. I keep coming across "double row angular contact" ..which is a
bit odd as these appear to be simple single row shielded bearings.

Does anyone have a Cheap source and does anyone have a listing of actual
bearing numbers that make up the bearings in an Hardinge HLV-H threading
gearbox?

Id rather not take each assembly apart and toss em into a
box...brrr!....I want to buy the bearings, and rebuild each individual
cluster and then stick it back into the machine.

There may..may be other bearing numbers needed..hence my request for
bearing list. Ive not pulled all the clusters out. The two that I have
pulled..have gritty bearings..nasty.

Gunner

I am the Sword of my Family
and the Shield of my Nation.
If sent, I will crush everything you have built,
burn everything you love,
and kill every one of you.
* * * * *(Hebrew quote)

Gunner

vxb.com

Bob AZ

On Tue, 14 Sep 2010 21:31:01 -0700 (PDT), Bob AZ
wrote:

On Sep 14, 2:39*pm, Gunner Asch wrote:
Im getting ready to replace the bearings in my Hardinge HLV-H threading
gearbox and am having a bit of a difficulty finding "3200" bearings
online. I keep coming across "double row angular contact" ..which is a
bit odd as these appear to be simple single row shielded bearings.

Does anyone have a Cheap source and does anyone have a listing of actual
bearing numbers that make up the bearings in an Hardinge HLV-H threading
gearbox?

Id rather not take each assembly apart and toss em into a
box...brrr!....I want to buy the bearings, and rebuild each individual
cluster and then stick it back into the machine.

There may..may be other bearing numbers needed..hence my request for
bearing list. Ive not pulled all the clusters out. The two that I have
pulled..have gritty bearings..nasty.

Gunner

I am the Sword of my Family
and the Shield of my Nation.
If sent, I will crush everything you have built,
burn everything you love,
and kill every one of you.
* * * * *(Hebrew quote)

Gunner

vxb.com

Bob AZ


Odd..they dont appear to be selling bearings. Is there a better link?

Gunner


I am the Sword of my Family
and the Shield of my Nation.
If sent, I will crush everything you have built,
burn everything you love,
and kill every one of you.
(Hebrew quote)

On Tue, 14 Sep 2010 23:22:37 -0700, Gunner Asch
wrote:

On Tue, 14 Sep 2010 21:31:01 -0700 (PDT), Bob AZ
wrote:

vxb.com

Odd..they dont appear to be selling bearings. Is there a better link?

What pranet you from? Works for me. Doublecheck your fyping tingers.

16mm x 60" LMS kits for $60.

10-packs of 3200 bearings for $39.95 12x24x6mm?!?

--
Not merely an absence of noise, Real Silence begins
when a reasonable being withdraws from the noise in
order to find peace and order in his inner sanctuary.
-- Peter Minard

On Wed, 15 Sep 2010 08:04:57 -0700, Larry Jaques
wrote:

vxb.com

My mistake..I automatically entered www.vxb.com

Try it.....

Gunner


I am the Sword of my Family
and the Shield of my Nation.
If sent, I will crush everything you have built,
burn everything you love,
and kill every one of you.
(Hebrew quote)

On Wed, 15 Sep 2010 08:04:57 -0700, Larry Jaques
wrote:

vxb.com


http://www.vxb.com/page/bearings/PROD/Kit240_1

These look cheap enough, yet USA made (according to the picture..shrug)

Rubber shielded or ZZ shielded would be better in the guts of a lathe
gear box?

Most of the lathes I service have gearboxes in oil..so they are open
sided


Gunner


I am the Sword of my Family
and the Shield of my Nation.
If sent, I will crush everything you have built,
burn everything you love,
and kill every one of you.
(Hebrew quote)

On Wed, 15 Sep 2010 08:32:14 -0700, Gunner Asch
wrote:

On Wed, 15 Sep 2010 08:04:57 -0700, Larry Jaques
wrote:

vxb.com


http://www.vxb.com/page/bearings/PROD/Kit240_1

These look cheap enough, yet USA made (according to the picture..shrug)

Rubber shielded or ZZ shielded would be better in the guts of a lathe
gear box?

Most of the lathes I service have gearboxes in oil..so they are open
sided


Gunner


Hell....looking at the small print...those folks are located smack in
the middle of where Ill be for the rest of the week...Ill just go in!

VXB.com Ball Bearings, NationSkander California Corp
2165 S Dupont Dr Unit F, Anaheim CA 92806, USA
Tel (714) 442-2740 | (800) 928-4430 | Fax (714) 442-9740

Thanks!!!

Gunner


I am the Sword of my Family
and the Shield of my Nation.
If sent, I will crush everything you have built,
burn everything you love,
and kill every one of you.
(Hebrew quote)

On Wed, 15 Sep 2010 09:13:23 -0800, Jon Anderson
wrote:

On 9/15/2010 7:32 AM, Gunner Asch wrote:

These look cheap enough, yet USA made (according to the picture..shrug)


How about these, Ebay item #400073172157
Deep groove, shielded, 10 pcs for $10.95. He's got lots of other
listings in this size. Might email and ask if he's got any USA bearings.
I've had decent success with import bearings, but if it's a total bitch
taking that gearbox apart and putting back together...

I bought a tube of 608 bearings to replace the stamped bearings in my
Total Gym, $7.95 for 10 bearings. VXB is the mfg. I suspect made in
China, though not marked. But they look and feel great.


Jon

Ill swing into VXB..they are in Anaheim and pick up some US made
bearings.

Rubber or steel shield?


Thanks!

Gunner


I am the Sword of my Family
and the Shield of my Nation.
If sent, I will crush everything you have built,
burn everything you love,
and kill every one of you.
(Hebrew quote)

On 9/15/2010 7:32 AM, Gunner Asch wrote:

These look cheap enough, yet USA made (according to the picture..shrug)


How about these, Ebay item #400073172157
Deep groove, shielded, 10 pcs for $10.95. He's got lots of other
listings in this size. Might email and ask if he's got any USA bearings.
I've had decent success with import bearings, but if it's a total bitch
taking that gearbox apart and putting back together...

I bought a tube of 608 bearings to replace the stamped bearings in my
Total Gym, $7.95 for 10 bearings. VXB is the mfg. I suspect made in
China, though not marked. But they look and feel great.


Jon

On 9/15/2010 9:08 AM, Gunner Asch wrote:

Ill swing into VXB..they are in Anaheim and pick up some US made
bearings.

Rubber or steel shield?

Personally I'd go with sealed in that application, just to insure
nothing got into the bearing.

Jon