Home |
Search |
Today's Posts |
|
Metalworking (rec.crafts.metalworking) Discuss various aspects of working with metal, such as machining, welding, metal joining, screwing, casting, hardening/tempering, blacksmithing/forging, spinning and hammer work, sheet metal work. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
#1
Posted to rec.crafts.metalworking
|
|||
|
|||
Catalytic converters
On Wed, 27 Aug 2008 23:17:07 -0400, Gerald Miller wrote:
A recently solved case here involved bronze memorial urns from a local cemetery, something like 175 urns on their way to a scrap yard 50 miles away. Gerry :-)} London, Canada We've had a spate of drain and manhole cover thefts. Very quick job for the scum to get a few tons of cast iron scrap, very high cost to replace, since new covers often do not fit old frames, so the road has to be dug up and it all replaced. Potentially very bad news if you drive along the road just after the theft :-| Mark Rand RTFM |
#2
Posted to rec.crafts.metalworking
|
|||
|
|||
Catalytic converters
On Aug 28, 7:28 pm, Mark Rand wrote:
On Wed, 27 Aug 2008 23:17:07 -0400, Gerald Miller wrote: A recently solved case here involved bronze memorial urns from a local cemetery, something like 175 urns on their way to a scrap yard 50 miles away. Gerry :-)} London, Canada We've had a spate of drain and manhole cover thefts. Very quick job for the scum to get a few tons of cast iron scrap, very high cost to replace, since new covers often do not fit old frames, so the road has to be dug up and it all replaced. Potentially very bad news if you drive along the road just after the theft :-| Mark Rand RTFM There's a business idea just waiting for someone to do it- sized manhole and drain covers! get 'em made oversize and find a bigass (but short bed) lathe and turn to size. Dave |
#3
Posted to rec.crafts.metalworking
|
|||
|
|||
Catalytic converters
|
#4
Posted to rec.crafts.metalworking
|
|||
|
|||
Catalytic converters
On Fri, 29 Aug 2008 20:00:32 -0400, Gerald Miller wrote:
On Fri, 29 Aug 2008, wrote: There's a business idea just waiting for someone to do it- sized manhole and drain covers! get 'em made oversize and find a bigass (but short bed) lathe and turn to size. Back in 1974, the electrical sub-contractor wanted to substitute 24" covers for the specified 30" covers on electrical manholes constructed as part of an airfield contract. When asked for justification for my refusal, I told him "neither the airfield electrician, or my electrical inspector (both of whom were present) will fit through a 24" hole, there was no more discussion on the topic. "Well, there's your problem!" Wheel bearing grease and a plunger... I'd be more worried about finding a manhole sealing ring "bathtub" that fits if you buy the non-standard holes. That tub can be a godsend if you are down in a hole with live connections open, the hole is at a low spot or even in the gutter, and it starts raining... GTE used to be paranoid - air up the innertube seal AND cement it down with quick-setting grout. Then again, if we had a few 4200-pair paper trunk cables open down there, the screw-up potential is huge. -- Bruce -- |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Catalytic converters | Metalworking | |||
Catalytic converters | Metalworking | |||
They're not really DTV converters ! | Home Repair | |||
Catalytic Converters for Small engines | Home Repair | |||
Coleman Powermatic catalytic heater | Woodworking |