Home |
Search |
Today's Posts |
|
Metalworking (rec.crafts.metalworking) Discuss various aspects of working with metal, such as machining, welding, metal joining, screwing, casting, hardening/tempering, blacksmithing/forging, spinning and hammer work, sheet metal work. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
#1
Posted to rec.crafts.metalworking
|
|||
|
|||
3 jaw chuck for rotary table
I'm looking for a 3 jaw chuck that would mount using the T slots on my
rotary table. Any ideas? What do you call that type of mounting? Stu |
#2
Posted to rec.crafts.metalworking
|
|||
|
|||
3 jaw chuck for rotary table
I'm looking for a 3 jaw chuck that would mount using the T slots on my rotary table. Any ideas? What do you call that type of mounting? I call it a home made mounting. It may be made but I've not seen it. I just made a plate a bit larger than the chuck. Four holes around the perimeter to mount to the table. Karl |
#3
Posted to rec.crafts.metalworking
|
|||
|
|||
3 jaw chuck for rotary table
Stuart & Kathryn Fields wrote:
I'm looking for a 3 jaw chuck that would mount using the T slots on my rotary table. Any ideas? What do you call that type of mounting? Stu Got a lathe too ? Buy a chunk of metal and make a mount plate for an off-the-shelf chuck . Square piece just a bit bigger than the chuck diameter , turn it to fit the chuck back , slot the corners . Mild steel seems to be a pretty decent choice , price-wise . Haven't checked cast iron , but aluminum and brass/bronze are pricey in Memphis Tn . -- Snag wannabe machinist in the middle of a taper attachment project - from scrap ! |
#4
Posted to rec.crafts.metalworking
|
|||
|
|||
3 jaw chuck for rotary table
Stuart & Kathryn Fields wrote:
I'm looking for a 3 jaw chuck that would mount using the T slots on my rotary table. Any ideas? What do you call that type of mounting? Stu I made a mounting plate for a small 3 jaw out of 1/2" aluminum plate. I have not seen a commercial one anywhere. Good Luck, BobH |
#5
Posted to rec.crafts.metalworking
|
|||
|
|||
3 jaw chuck for rotary table
BobH wrote:
Stuart & Kathryn Fields wrote: I'm looking for a 3 jaw chuck that would mount using the T slots on my rotary table. Any ideas? What do you call that type of mounting? Stu I made a mounting plate for a small 3 jaw out of 1/2" aluminum plate. I have not seen a commercial one anywhere. Good Luck, BobH I made one as well( out of mild steel round stock). I stepped the mounting plate to locate the chuck and used cap screws and t-nuts to hold it in place. Works very well. |
#6
Posted to rec.crafts.metalworking
|
|||
|
|||
3 jaw chuck for rotary table
On Sat, 09 Aug 2008 22:07:52 -0500, Terry Coombs wrote:
Stuart & Kathryn Fields wrote: I'm looking for a 3 jaw chuck that would mount using the T slots on my rotary table. Any ideas? What do you call that type of mounting? Stu Got a lathe too ? Buy a chunk of metal and make a mount plate for an off-the-shelf chuck . Square piece just a bit bigger than the chuck diameter , turn it to fit the chuck back , slot the corners . Mild steel seems to be a pretty decent choice , price-wise . Haven't checked cast iron , but aluminum and brass/bronze are pricey in Memphis Tn . A 1" thick by 6" diameter plate of cast from McMaster was something like $45 a few years ago -- I made that adapter plate from mild steel from the scrap yard. Stu: I don't know how common it is, but the chucks on my Smithy are designed to mount to a plate with a turned shoulder in it -- if you're careful you can nicely center the chuck. In turn, most rotary tables I've seen have a hole in the center, which, if it isn't too bunged up, you could make a shoulder for on your adapter to put your chuck in the center of the whole business. -- Tim Wescott Control systems and communications consulting http://www.wescottdesign.com Need to learn how to apply control theory in your embedded system? "Applied Control Theory for Embedded Systems" by Tim Wescott Elsevier/Newnes, http://www.wescottdesign.com/actfes/actfes.html |
#7
Posted to rec.crafts.metalworking
|
|||
|
|||
3 jaw chuck for rotary table
A lathe 3 jaw chuck on a faceplate. Mount the faceplate to another.
And have the non-lathe one T-mount and larger. Or just buy a Bison and a backplate - and go from there. Martin Martin H. Eastburn @ home at Lions' Lair with our computer lionslair at consolidated dot net TSRA, Endowed; NRA LOH & Patron Member, Golden Eagle, Patriot's Medal. NRA Second Amendment Task Force Charter Founder IHMSA and NRA Metallic Silhouette maker & member. http://lufkinced.com/ Stuart & Kathryn Fields wrote: I'm looking for a 3 jaw chuck that would mount using the T slots on my rotary table. Any ideas? What do you call that type of mounting? Stu ----== Posted via Pronews.Com - Unlimited-Unrestricted-Secure Usenet News==---- http://www.pronews.com The #1 Newsgroup Service in the World! 100,000 Newsgroups ---= - Total Privacy via Encryption =--- |
#8
Posted to rec.crafts.metalworking
|
|||
|
|||
3 jaw chuck for rotary table
Stuart & Kathryn Fields wrote:
I'm looking for a 3 jaw chuck that would mount using the T slots on my rotary table. Any ideas? What do you call that type of mounting? Stu Like others have mentioned, I made my own. A round disc slightly larger than the chuck to allow room for cap screws around the chuck, with 3 holes in my case as the 10" rotary table has 6 slots. The cap screws go into T slot nuts which I had already made for the table. The plate is shouldered like you would fit a chuck backplate, A nice feature is I also fitted an accurate centering plug in the middle of the disc so I can just fit the chuck on the rotary table and it is centered, the plug is removable so I can fit the chuck and backplate straight onto the mill table if required. |
#9
Posted to rec.crafts.metalworking
|
|||
|
|||
3 jaw chuck for rotary table
On Aug 9, 10:30*pm, "Stuart & Kathryn Fields" wrote:
I'm looking for a 3 jaw chuck that would mount using the T slots on my rotary table. *Any ideas? *What do you call that type of mounting? Stu Look for a "Front Mount Chuck" with through holes. |
#10
Posted to rec.crafts.metalworking
|
|||
|
|||
3 jaw chuck for rotary table
I have one for sale on ebay right now.
Search for "bison rotary table chuck 6". Mine is new. Basically you need chuck with through holes for Socket Head Hex Screws drilled. i On 2008-08-10, Stuart & Kathryn Fields wrote: I'm looking for a 3 jaw chuck that would mount using the T slots on my rotary table. Any ideas? What do you call that type of mounting? Stu |
#11
Posted to rec.crafts.metalworking
|
|||
|
|||
3 jaw chuck for rotary table
"Ignoramus6985" wrote in message ... I have one for sale on ebay right now. Search for "bison rotary table chuck 6". Mine is new. Basically you need chuck with through holes for Socket Head Hex Screws drilled. Looked at your 3 jaw chuck. Question: My rotary table has 4 slots @ 90° for T nuts. (Now that I know how to do °, I use it a lot for practice)** Your 3 jaw has 3 holes @ 120 °.** It would seem that another plate would be required to mount that chuck on my rotary table. Is that true? Am I missing something? I'm an owner of machine tools, for sure not qualified to use the word machinist associated with my skills. But dang the tools are handy. ** Its not 3 o'clock, I write: the big hand is @ 0° and the little hand is @ 90° (more ° alt 0176 practice) stu On 2008-08-10, Stuart & Kathryn Fields wrote: I'm looking for a 3 jaw chuck that would mount using the T slots on my rotary table. Any ideas? What do you call that type of mounting? Stu |
#12
Posted to rec.crafts.metalworking
|
|||
|
|||
3 jaw chuck for rotary table
On 2008-08-10, Stuart & Kathryn Fields wrote:
"Ignoramus6985" wrote in message ... I have one for sale on ebay right now. Search for "bison rotary table chuck 6". Mine is new. Basically you need chuck with through holes for Socket Head Hex Screws drilled. Looked at your 3 jaw chuck. Question: My rotary table has 4 slots @ 90° for T nuts. (Now that I know how to do °, I use it a lot for practice)** Your 3 jaw has 3 holes @ 120 °.** It would seem that another plate would be required to mount that chuck on my rotary table. Is that true? Am I missing something? I'm an owner of machine tools, for sure not qualified to use the word machinist associated with my skills. But dang the tools are handy. ** Its not 3 o'clock, I write: the big hand is @ 0° and the little hand is @ 90° (more ° alt 0176 practice) Stu, that's a good question and I am out of my "depth" to answer it. I would hate to give you a wrong answer. But what I know is that with front mounts, you can get away with thinner mounting plates. i stu On 2008-08-10, Stuart & Kathryn Fields wrote: I'm looking for a 3 jaw chuck that would mount using the T slots on my rotary table. Any ideas? What do you call that type of mounting? Stu |
#13
Posted to rec.crafts.metalworking
|
|||
|
|||
3 jaw chuck for rotary table
On Aug 10, 1:31*pm, Ignoramus6985
wrote: On 2008-08-10, Stuart & Kathryn Fields wrote: Looked at your 3 jaw chuck. *Question: *My rotary table has 4 slots @ 90° for T nuts. Your 3 jaw has 3 holes @ 120 °. *It would seem that another plate would be required to mount that chuck on my rotary table. *Is that true? *Am I missing something? My second-hand rotary table has tapped holes all over it from previous fixtures. None of them weaken the tee slots and they don't interfere with using it. Why not screw the chuck directly to the table? If there's room, you could use undersized mounting screws and make blocks that screw down in the tee slots with lateral screws to center the chuck better. If the three front screws go through a ring of solid metal in the chuck, maybe you could drill a 4-hole pattern in it as well. |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Experience with Grizzly H7506 Horizontal/Vertical Rotary IndexingTable with Chuck? | Metalworking | |||
Rotary table | Metalworking | |||
Bison rotary table | Metalworking | |||
Rotary table ID? | Metalworking | |||
Rotary table help. | Metalworking |