In article ,
Ignoramus23984 wrote:

OK... I think that I have the answer... I have a 8x4 wooden
board/member. If I place one end of it in the middle of my tailgate,
and the other on the ground, it becomes a relatively secure slide for
those 152 lbs devices. There is about 10-12" drop from the end of the
tailgate to the board, but, I think, I should be able to handle that
easily. Lowering that thing to the ground is what is troublesome.


Word of advice (from experience) - make sure that you rig a way for the
board/beam to be hooked to the bumper. Gets painful and exciting when it
slips off the bumper mid-move.

Your tailgate should be trivial to remove. Most American trucks, you
remove the side supports, raise to 45 degrees, and pull up the right
side, then the left side comes out. Dropping heavy large things (even
8-12") onto narrower boards is another recipe for pain.

My suggestion, particularly given the amount of junk you move, is to get
a nice cheap refrigerator dolly - two wheels, a short bit on the bottom,
a long upright/handle section. Then nail up a set of ramps, or one wider
ramp (with some sort of hook for the bumper on either type) and roll
things into or out of the truck. Simpler and safer, and useful in the
long run for other things.

--
Cats, coffee, chocolate...vices to live by

"Ignoramus16172" wrote in message
.. .
On Fri, 03 Mar 2006 14:56:18 GMT, Ecnerwal
wrote:
In article ,
Ignoramus23984 wrote:

OK... I think that I have the answer... I have a 8x4 wooden
board/member. If I place one end of it in the middle of my tailgate,
and the other on the ground, it becomes a relatively secure slide
for
those 152 lbs devices. There is about 10-12" drop from the end of
the
tailgate to the board, but, I think, I should be able to handle that
easily. Lowering that thing to the ground is what is troublesome.


Word of advice (from experience) - make sure that you rig a way for
the
board/beam to be hooked to the bumper. Gets painful and exciting when
it
slips off the bumper mid-move.

Yes, absolutely. There is a little "step" into the garage and I will
use that as a stop for the board.

Your tailgate should be trivial to remove. Most American trucks, you
remove the side supports, raise to 45 degrees, and pull up the right
side, then the left side comes out. Dropping heavy large things (even
8-12") onto narrower boards is another recipe for pain.

I will check, if I can do it, I will remove the tailgate.

My suggestion, particularly given the amount of junk you move, is to
get
a nice cheap refrigerator dolly - two wheels, a short bit on the
bottom,
a long upright/handle section. Then nail up a set of ramps, or one
wider
ramp (with some sort of hook for the bumper on either type) and roll
things into or out of the truck. Simpler and safer, and useful in the
long run for other things.

What he said - we call that sort of dolly a "handtruck" and, although we
don't use it often, it's great to have here when we need it. Available
at any good hardware store or home center.

They also make ramps for getting a motorcycle or similar in and out of a
pickup truck - you could check out those, but a couple of 2x6's would
probably work as well for the handtruck or even just sliding your 150
lb. objects.

-S-
http://www.kbnj.com

Thanks Ecnerwal. I will check into it...

"Ecnerwal" wrote in message
...
In article ,
Ignoramus23984 wrote:

OK... I think that I have the answer... I have a 8x4 wooden
board/member. If I place one end of it in the middle of my tailgate,
and the other on the ground, it becomes a relatively secure slide for
those 152 lbs devices. There is about 10-12" drop from the end of the
tailgate to the board, but, I think, I should be able to handle that
easily. Lowering that thing to the ground is what is troublesome.


Word of advice (from experience) - make sure that you rig a way for the
board/beam to be hooked to the bumper. Gets painful and exciting when it
slips off the bumper mid-move.


What I have done is just to drill a hole through the ramp top and the tail
gate. Need a bit of touvh up paint for this. Then put a carriage bolt
through them both.


Your tailgate should be trivial to remove. Most American trucks, you
remove the side supports, raise to 45 degrees, and pull up the right
side, then the left side comes out. Dropping heavy large things (even
8-12") onto narrower boards is another recipe for pain.

My suggestion, particularly given the amount of junk you move, is to get
a nice cheap refrigerator dolly - two wheels, a short bit on the bottom,
a long upright/handle section. Then nail up a set of ramps, or one wider
ramp (with some sort of hook for the bumper on either type) and roll
things into or out of the truck. Simpler and safer, and useful in the
long run for other things.


You can get those cheap at costco. I have had mine for over twenty years and
it has saved my ass again and again. You can grab on top and put somebody
on the bottom and lower some pretty substantial weights.

I have also built ramps for these things. I always put down a small ridge a
couple of inches wider than the tires. That way the dolly won't wander off
the ramp. Some 1 X 2 nailed or srewed to the ramp is adequate.