Home |
Search |
Today's Posts |
|
Metalworking (rec.crafts.metalworking) Discuss various aspects of working with metal, such as machining, welding, metal joining, screwing, casting, hardening/tempering, blacksmithing/forging, spinning and hammer work, sheet metal work. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
|
#1
|
|||
|
|||
Photos of my homemade TIG torch cooler
Ignoramus26745 wrote: I made a homemade TIG torch cooler, from a used carbonator pump from soda fountains. Pictures of the pump, solid state relay, etc, are provided. Also provided are pictures of the innards of my welder. The story is he http://igor.chudov.com/projects/Weld...-Torch-Cooler/ Hey, I thought you said a couple of weeks ago that it did NOT have HF. Obviously, in the lower left corner of the pics of the welder's innards, is the HF section. Maybe you meant it wasn't working, I don't know. I have to say the inside of my Lincoln Square-Wave TIG 300 is a lot more organized than the Hobart. There is VERY little wiring in the main welder section other than the main power cables. All the circuit boards and interconnect wiring is in an enclosed space behind the control panel. I'm almost amazed the Hobart works at all with all the control wiring hanging out near the main power circuitry. (I do notice a big shield between the HF and the control boards. By the way, you may be breaking the shielding with your new wires for the cooler. They go right by the HF section, then up near the control boards. I would not route them that way.) Your cooler looks pretty good. I wonder, however, if you get into serious TIGing, if the heat will build up. I was pretty surprised at how hot the cooler got on my TIG system after some steel welding. (Actually, it probably gets hotter on Aluminum with AC, but I am still learning the techniques there, so I weld for a moment and then look at the part a lot.) I have a Miller cooler with a big fan-cooled heat exchanger on it. The exchanger gets hot, and the water in the tank eventually gets pretty warm, too. Jon |
#2
|
|||
|
|||
Photos of my homemade TIG torch cooler
Jon Elson wrote:
Ignoramus26745 wrote: I made a homemade TIG torch cooler, from a used carbonator pump from soda fountains. Pictures of the pump, solid state relay, etc, are provided. Also provided are pictures of the innards of my welder. The story is he http://igor.chudov.com/projects/Weld...-Torch-Cooler/ Hey, I thought you said a couple of weeks ago that it did NOT have HF. Obviously, in the lower left corner of the pics of the welder's innards, is the HF section. Maybe you meant it wasn't working, I don't know. I have to say the inside of my Lincoln Square-Wave TIG 300 is a lot more organized than the Hobart. There is VERY little wiring in the main welder section other than the main power cables. All the circuit boards and interconnect wiring is in an enclosed space behind the control panel. I'm almost amazed the Hobart works at all with all the control wiring hanging out near the main power circuitry. (I do notice a big shield between the HF and the control boards. By the way, you may be breaking the shielding with your new wires for the cooler. They go right by the HF section, then up near the control boards. I would not route them that way.) I agree: I would not run any wires into that bottom box (with the HF) if at all possible, and if I really did need to run wires into that box, I would keep them clipped to the metal wall so as to be as far as possible from the HF coils, and to minimise the flux flowing in the loop between the wire and the metal wall. Certainly don't try putting any of your new circuitry into that box with the HF. I think the top box looks more promising as a place for the new circuitry. By the way, you could water-cool the IGBTs, that works really well as long as you put a safety thermal switch to shut things down if the water stops. The method I prefer is a slab of copper busbar maybe 3 inches wide, quarter inch thick and as long as needed to bolt down all the IGBTs. First drill and tap it for the IGBTs, mounting holes etc. whilst it's still hard copper and easy to tap. Then use silver solder (not soft solder but the sort that melts when it is almost red hot) to attach a zig-zag of maybe quarter inch diameter copper pipe to the back of the busbar, trying not to get solder into the holes you tapped before. Make sure that the copper pipe fits well to the back of the busbar before starting to solder it. I would also recommend making the ends of the copper pipe long enough so that they protrude outside the welder and there are no joints in the plumbing inside the welder casing. This way, if you make the pipes slope downward, then if the joints in the pipework should leak, the water will stay out of the wiring. You can get rid of several kW with this sort of water cooling. Chris [...] |
#3
|
|||
|
|||
Photos of my homemade TIG torch cooler
On Thu, 03 Nov 2005 16:08:14 -0600, Jon Elson
wrote: Your cooler looks pretty good. I wonder, however, if you get into serious TIGing, if the heat will build up. I was pretty surprised at how hot the cooler got on my TIG system after some steel welding. (Actually, it probably gets hotter on Aluminum with AC, but I am still learning the techniques there, so I weld for a moment and then look at the part a lot.) I have a Miller cooler with a big fan-cooled heat exchanger on it. The exchanger gets hot, and the water in the tank eventually gets pretty warm, too. Jon note on the cooler getting hot; don't know how much coolant does the miller cooler holds and why it gets hot, but one thing for sure the new miller 250 TIGs we used at school the fan does not come on untill the coolant get hot enough. it may even have some sort of flow control as well, because the sight glass with the red star in it was barely spinning at 90-120amp welding it has been said many times by guys here, a 5 gallon bucket or ever 4 gallon will never get hot enough (not even remotely) under normal use. I asked the same question back when I built mine and Ernie L. and the other well known gurus confirmed it. NO heat exchanger needed. unless you are blasting 300Amp continuosly. |
#4
|
|||
|
|||
Photos of my homemade TIG torch cooler
acrobat ants wrote: On Thu, 03 Nov 2005 16:08:14 -0600, Jon Elson wrote: Your cooler looks pretty good. I wonder, however, if you get into serious TIGing, if the heat will build up. I was pretty surprised at how hot the cooler got on my TIG system after some steel welding. (Actually, it probably gets hotter on Aluminum with AC, but I am still learning the techniques there, so I weld for a moment and then look at the part a lot.) I have a Miller cooler with a big fan-cooled heat exchanger on it. The exchanger gets hot, and the water in the tank eventually gets pretty warm, too. Jon note on the cooler getting hot; don't know how much coolant does the miller cooler holds My Miller cooler holds just short of a full gallon, including what is in the torch hoses. I'm using Miller coolant straight, it is supposed to help the pump and prevent corrosion in the torch, etc. On mine, the fan is mounted on the pump motor's shaft, so it runs all the time, too. Jon |
#5
|
|||
|
|||
Photos of my homemade TIG torch cooler
Sounds like a heat exchanger is needed - as one loop from the stinger brings
in hot water and pumps back warm water - another loop is placed to chill the warming water (water to say a term only) and dump the heat elsewhere. A nice portable air conditioner that is a heat pump or not - could be implemented when local power was available. When in the field, a Icebox from a camper that runs on 12 v or propane might be a nice chiller. Naturally some kit bashing and creative mind work would have to take place. Solar cells dumping high current into a pair of wires that in turn run through a solid state heat sink (ever see the 12 volt camping ice/beer chests ?) easy to bash. Almost done for you - cooling tank and drain and 12volt plug. Plug it in and pump 'water' through 3/8" copper tubing - (or other) to a small radiator that might have been a motorcycle add on kit - back to the 12 volt chiller. The box always closed and in the shade - and the bottom (where the heat is - on a larger sheet of metal to conduct ? - truck bed ? Martin - just had dinner and under boosted blood stream! Martin Eastburn @ home at Lions' Lair with our computer lionslair at consolidated dot net NRA LOH, NRA Life NRA Second Amendment Task Force Charter Founder acrobat ants wrote: On Thu, 03 Nov 2005 16:08:14 -0600, Jon Elson wrote: Your cooler looks pretty good. I wonder, however, if you get into serious TIGing, if the heat will build up. I was pretty surprised at how hot the cooler got on my TIG system after some steel welding. (Actually, it probably gets hotter on Aluminum with AC, but I am still learning the techniques there, so I weld for a moment and then look at the part a lot.) I have a Miller cooler with a big fan-cooled heat exchanger on it. The exchanger gets hot, and the water in the tank eventually gets pretty warm, too. Jon note on the cooler getting hot; don't know how much coolant does the miller cooler holds and why it gets hot, but one thing for sure the new miller 250 TIGs we used at school the fan does not come on untill the coolant get hot enough. it may even have some sort of flow control as well, because the sight glass with the red star in it was barely spinning at 90-120amp welding it has been said many times by guys here, a 5 gallon bucket or ever 4 gallon will never get hot enough (not even remotely) under normal use. I asked the same question back when I built mine and Ernie L. and the other well known gurus confirmed it. NO heat exchanger needed. unless you are blasting 300Amp continuosly. ----== Posted via Newsfeeds.Com - Unlimited-Unrestricted-Secure Usenet News==---- http://www.newsfeeds.com The #1 Newsgroup Service in the World! 120,000+ Newsgroups ----= East and West-Coast Server Farms - Total Privacy via Encryption =---- |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Photos of my homemade TIG torch cooler | Metalworking | |||
Photos of my homemade TIG torch cooler | Metalworking | |||
Carbonator questions (TIG torch cooler) | Metalworking | |||
Carbonator questions (TIG torch cooler) | Metalworking | |||
Torch Cooler Pictures in Dropbox | Metalworking |