Here is something I should be able to figure out but can’t. I have a
Sargon model 652 DRO now on my lathe. (It has no numeric key pad). How
do I zero this thing so I can get a direct radius or diameter reading
for a bar I would be turning?

The radius is off by a factor of 2 and the diameter is off by a factor
of 4.

TIA

Jake in Escondido

No Takers?

Jake in Escondido wrote:
Here is something I should be able to figure out but can’t. I have a
Sargon model 652 DRO now on my lathe. (It has no numeric key pad). How
do I zero this thing so I can get a direct radius or diameter reading
for a bar I would be turning?

The radius is off by a factor of 2 and the diameter is off by a factor
of 4.

TIA

Jake in Escondido

"Jake in Escondido" wrote in message
news:MNNme.27079$Gp.7386@fed1read04...
Here is something I should be able to figure out but can’t. I have a
Sargon model 652 DRO now on my lathe. (It has no numeric key pad). How do
I zero this thing so I can get a direct radius or diameter reading for a
bar I would be turning?

The radius is off by a factor of 2 and the diameter is off by a factor of
4.

Sounds like the resolution might be wrong, I don't know how you would change
it without a keypad. Got the operator's manual?

The manual for the unit will show some examples of the diplay appearance
while changing the settings, but you might be able to select the correct
settings by using the following steps (which are from notes I kept from the
manual of the same unit).
If I had a manual, I'd send you a copy. Maybe someone else can.

If you have compatible scales connected, you can probably come up with the
correct settings by experimentation or trial & error.

- Turn Power on
- Push/hold A/I
= one of the Setup screens wil be displayed
- Release A/I
= unit is now in Setup Mode

- Press Rad/Dia to advance to the desired screen (field)
- Press Reset to change parameter setting
- Press Rad/Dia to advance to desired screen (field)
- Press Reset to change another setting
- Exit Setup Mode (saves selected setting(s), by pressing A/I

WB
............

"Jake in Escondido" wrote in message
news:MNNme.27079$Gp.7386@fed1read04...
Here is something I should be able to figure out but can’t. I have a
Sargon model 652 DRO now on my lathe. (It has no numeric key pad). How
do I zero this thing so I can get a direct radius or diameter reading
for a bar I would be turning?

The radius is off by a factor of 2 and the diameter is off by a factor
of 4.

TIA

Jake in Escondido





----== Posted via Newsfeeds.Com - Unlimited-Uncensored-Secure Usenet News==----
http://www.newsfeeds.com The #1 Newsgroup Service in the World! 120,000+ Newsgroups
----= East and West-Coast Server Farms - Total Privacy via Encryption =----

Thanks Wild Bill and John,

I downloaded the manual from their website. There is not a lot of
information in it. The scales supposedly are the the ones that came with
it from the factory.

I'll try your process and see what happens. I'll also ping their
Customer Service.

Jake

Wild Bill wrote:
The manual for the unit will show some examples of the diplay appearance
while changing the settings, but you might be able to select the correct
settings by using the following steps (which are from notes I kept from the
manual of the same unit).
If I had a manual, I'd send you a copy. Maybe someone else can.

If you have compatible scales connected, you can probably come up with the
correct settings by experimentation or trial & error.

- Turn Power on
- Push/hold A/I
= one of the Setup screens wil be displayed
- Release A/I
= unit is now in Setup Mode

- Press Rad/Dia to advance to the desired screen (field)
- Press Reset to change parameter setting
- Press Rad/Dia to advance to desired screen (field)
- Press Reset to change another setting
- Exit Setup Mode (saves selected setting(s), by pressing A/I

WB
...........

"Jake in Escondido" wrote in message
news:MNNme.27079$Gp.7386@fed1read04...

Here is something I should be able to figure out but can’t. I have a
Sargon model 652 DRO now on my lathe. (It has no numeric key pad). How
do I zero this thing so I can get a direct radius or diameter reading
for a bar I would be turning?

The radius is off by a factor of 2 and the diameter is off by a factor
of 4.

TIA

Jake in Escondido






----== Posted via Newsfeeds.Com - Unlimited-Uncensored-Secure Usenet News==----
http://www.newsfeeds.com The #1 Newsgroup Service in the World! 120,000+ Newsgroups
----= East and West-Coast Server Farms - Total Privacy via Encryption =----

I finally conceded and called the factory. They were quite helpful. The
problem had to do with my resolution setting. It should have been .0002
rather than .0005. I doubt that I would have figured that out on my own
and it sure wasn't mentioned in the manual. Thanks to all that replied.

Jake


Jake in Escondido wrote:
Thanks Wild Bill and John,

I downloaded the manual from their website. There is not a lot of
information in it. The scales supposedly are the the ones that came with
it from the factory.

I'll try your process and see what happens. I'll also ping their
Customer Service.

Jake

Wild Bill wrote:

The manual for the unit will show some examples of the diplay appearance
while changing the settings, but you might be able to select the correct
settings by using the following steps (which are from notes I kept
from the
manual of the same unit).
If I had a manual, I'd send you a copy. Maybe someone else can.

If you have compatible scales connected, you can probably come up with
the
correct settings by experimentation or trial & error.

- Turn Power on
- Push/hold A/I
= one of the Setup screens wil be displayed
- Release A/I
= unit is now in Setup Mode

- Press Rad/Dia to advance to the desired screen (field)
- Press Reset to change parameter setting
- Press Rad/Dia to advance to desired screen (field)
- Press Reset to change another setting
- Exit Setup Mode (saves selected setting(s), by pressing A/I

WB
...........

"Jake in Escondido" wrote in message
news:MNNme.27079$Gp.7386@fed1read04...

Here is something I should be able to figure out but can’t. I have a
Sargon model 652 DRO now on my lathe. (It has no numeric key pad). How
do I zero this thing so I can get a direct radius or diameter reading
for a bar I would be turning?

The radius is off by a factor of 2 and the diameter is off by a factor
of 4.

TIA

Jake in Escondido






----== Posted via Newsfeeds.Com - Unlimited-Uncensored-Secure Usenet
News==----
http://www.newsfeeds.com The #1 Newsgroup Service in the World!
120,000+ Newsgroups
----= East and West-Coast Server Farms - Total Privacy via Encryption
=----

Good deal, glad it's reading correctly for ya. I didn't look over the entire
online manual to what was included in it. I had a 652 unit and a manual,
which I should now remember to copy any manual, to keep as a spare.

The settings for different scale resolutions for the 652 unit should be:
..0005, .0002, .0001, .00005, and .00002"

I think one compatible scale example is the LGG 330-14 miniscale
(5um/.0002").
5V TTL Quadrature

Scale compatibility includes the 100/105 Series 5V scales, and includes 100,
105, 110, 115, 130, 135 types with IM suffixes.

WB
...........

"Jake in Escondido" wrote in message
news:NAOne.5837$Wr.4339@fed1read04...
I finally conceded and called the factory. They were quite helpful. The
problem had to do with my resolution setting. It should have been .0002
rather than .0005. I doubt that I would have figured that out on my own
and it sure wasn't mentioned in the manual. Thanks to all that replied.

Jake





----== Posted via Newsfeeds.Com - Unlimited-Uncensored-Secure Usenet News==----
http://www.newsfeeds.com The #1 Newsgroup Service in the World! 120,000+ Newsgroups
----= East and West-Coast Server Farms - Total Privacy via Encryption =----

"Jake in Escondido" wrote in message
news:NAOne.5837$Wr.4339@fed1read04...
I finally conceded and called the factory. They were quite helpful. The
problem had to do with my resolution setting. It should have been .0002
rather than .0005. I doubt that I would have figured that out on my own and
it sure wasn't mentioned in the manual. Thanks to all that replied.

Jake

Had the same experience with my recently installed DRO, the manual gives
great instructions on how to change the resolution but no mention under what
circimstances it needs to be done.





Jake in Escondido wrote:
Thanks Wild Bill and John,

I downloaded the manual from their website. There is not a lot of
information in it. The scales supposedly are the the ones that came with
it from the factory.

I'll try your process and see what happens. I'll also ping their Customer
Service.

Jake

Wild Bill wrote:

The manual for the unit will show some examples of the diplay appearance
while changing the settings, but you might be able to select the correct
settings by using the following steps (which are from notes I kept from
the
manual of the same unit).
If I had a manual, I'd send you a copy. Maybe someone else can.

If you have compatible scales connected, you can probably come up with
the
correct settings by experimentation or trial & error.

- Turn Power on
- Push/hold A/I
= one of the Setup screens wil be displayed
- Release A/I
= unit is now in Setup Mode

- Press Rad/Dia to advance to the desired screen (field)
- Press Reset to change parameter setting
- Press Rad/Dia to advance to desired screen (field)
- Press Reset to change another setting
- Exit Setup Mode (saves selected setting(s), by pressing A/I

WB
...........

"Jake in Escondido" wrote in message
news:MNNme.27079$Gp.7386@fed1read04...

Here is something I should be able to figure out but can’t. I have a
Sargon model 652 DRO now on my lathe. (It has no numeric key pad). How
do I zero this thing so I can get a direct radius or diameter reading
for a bar I would be turning?

The radius is off by a factor of 2 and the diameter is off by a factor
of 4.

TIA

Jake in Escondido






----== Posted via Newsfeeds.Com - Unlimited-Uncensored-Secure Usenet
News==----
http://www.newsfeeds.com The #1 Newsgroup Service in the World! 120,000+
Newsgroups
----= East and West-Coast Server Farms - Total Privacy via Encryption
=----