By the way, I have a 6X18 Boyer Shultz surface ginder with a Walker
mag. for sale too. Cheap.

Jay



On Sun, 13 Jul 2003 16:07:28 GMT, Jay wrote:

Here's the story...

Back in 1997 I purchased an Enco mill/drill with a stand and a "Kurt"
type 4" vice. It was retrofit with a CNC stepper setup. The machine
worked perfectly and was used to machine a single polypropylene
plastic project and ran for about 80 hours. I decided that I needed a
full sized knee mill for additional future projects. Since I needed
the shop space, I restored the mill/drill to its original manual setup
and put it into storage.

I want to sell it or trade it. We are expanding our custom performance
engine-head porting and polishing department and I need to purchase a
few items. I need a new air compressor and a couple of good electric
die grinders (Dumore or equivalent). Since this machine is sitting,
without making me any money, I figure that I can let it go for the
cost of a compressor and a couple of die grinders and maybe get
someone into their own machine for a lot less than new.

A small Enco or equivalent compressor is around $279 and Dumore die
grinders are about 100 bucks each.

If anyone would like to discuss this, please email me first and I'll
give you a phone number. Remove the KILLSPAM out of the email
address. I am in the Salt Lake City area so just about any location
in the west is doable.

Thanks,

Jay

Salt Lake City area so just about any location
in the west is doable.

--
RellikJM
RellikJM AT Yahoo DOT Com
Don't forget about my "FREE" EPROM programming !
Advice is only worth what you paid for it!

"Kent Frazier" wrote in message
...
It would be nice if you would say what part of the world you live
Kent
"Jay" wrote in message
...
By the way, I have a 6X18 Boyer Shultz surface ginder with a Walker
mag. for sale too. Cheap.

Jay



On Sun, 13 Jul 2003 16:07:28 GMT, Jay wrote:

Here's the story...

Back in 1997 I purchased an Enco mill/drill with a stand and a "Kurt"
type 4" vice. It was retrofit with a CNC stepper setup. The machine
worked perfectly and was used to machine a single polypropylene
plastic project and ran for about 80 hours. I decided that I needed a
full sized knee mill for additional future projects. Since I needed
the shop space, I restored the mill/drill to its original manual setup
and put it into storage.

I want to sell it or trade it. We are expanding our custom performance
engine-head porting and polishing department and I need to purchase a
few items. I need a new air compressor and a couple of good electric
die grinders (Dumore or equivalent). Since this machine is sitting,
without making me any money, I figure that I can let it go for the
cost of a compressor and a couple of die grinders and maybe get
someone into their own machine for a lot less than new.

A small Enco or equivalent compressor is around $279 and Dumore die
grinders are about 100 bucks each.

If anyone would like to discuss this, please email me first and I'll
give you a phone number. Remove the KILLSPAM out of the email
address. I am in the Salt Lake City area so just about any location
in the west is doable.

Thanks,

Jay

Jay wrote in message . ..
Here's the story...

Back in 1997 I purchased an Enco mill/drill with a stand and a "Kurt"
type 4" vice. It was retrofit with a CNC stepper setup. The machine
worked perfectly and was used to machine a single polypropylene
plastic project and ran for about 80 hours. I decided that I needed a
full sized knee mill for additional future projects. Since I needed
the shop space, I restored the mill/drill to its original manual setup
and put it into storage.

I want to sell it or trade it. We are expanding our custom performance
engine-head porting and polishing department and I need to purchase a
few items. I need a new air compressor and a couple of good electric
die grinders (Dumore or equivalent). Since this machine is sitting,
without making me any money, I figure that I can let it go for the
cost of a compressor and a couple of die grinders and maybe get
someone into their own machine for a lot less than new.

A small Enco or equivalent compressor is around $279 and Dumore die
grinders are about 100 bucks each.

If anyone would like to discuss this, please email me first and I'll
give you a phone number. Remove the KILLSPAM out of the email
address. I am in the Salt Lake City area so just about any location
in the west is doable.

Thanks,

Jay


Hi Jay,
There was a guy on http://groups.yahoo.com/group/shop_tool_exchange/
looking for one of these