Before I build a brake for bending nice tight 90 deg. bends in 1/4" round,
was wondering if there is any piece of equipment out there that will do
this?

Was previously using a large Pexto brake but some numbnut tried to bend 3/8"
rebar and screwed it up and it's now signed "NO ROUND STOCK".

Thanks

-Tom

"TT" wrote in message
news:LYX3e.54379$Az.37205@lakeread02...
Before I build a brake for bending nice tight 90 deg. bends in 1/4" round,
was wondering if there is any piece of equipment out there that will do
this?

Sounds like a Diacro, but you might want to check out HF if you can't obtain
the Diacro

Was previously using a large Pexto brake but some numbnut tried to bend
3/8"
rebar and screwed it up and it's now signed "NO ROUND STOCK".

Thanks

-Tom

The only Diacro's I see are punch & die equipment.

-Tom

"ATP*" wrote in message
...

"TT" wrote in message
news:LYX3e.54379$Az.37205@lakeread02...
Before I build a brake for bending nice tight 90 deg. bends in 1/4"
round,
was wondering if there is any piece of equipment out there that will do
this?

Sounds like a Diacro, but you might want to check out HF if you can't
obtain
the Diacro

Was previously using a large Pexto brake but some numbnut tried to bend
3/8"
rebar and screwed it up and it's now signed "NO ROUND STOCK".

Thanks

-Tom

Look for rotary benders. I'm not sure if Diacro still makes them, but there
might be one or two on Ebay.

Mike

"TT" wrote in message
news:LRY3e.54389$Az.27198@lakeread02...
The only Diacro's I see are punch & die equipment.

-Tom

"ATP*" wrote in message
...

"TT" wrote in message
news:LYX3e.54379$Az.37205@lakeread02...
Before I build a brake for bending nice tight 90 deg. bends in 1/4"
round,
was wondering if there is any piece of equipment out there that will do
this?

Sounds like a Diacro, but you might want to check out HF if you can't
obtain
the Diacro

Was previously using a large Pexto brake but some numbnut tried to bend
3/8"
rebar and screwed it up and it's now signed "NO ROUND STOCK".

Thanks

-Tom

"TT" wrote in message
news:LYX3e.54379$Az.37205@lakeread02...
Before I build a brake for bending nice tight 90 deg. bends in 1/4" round,
was wondering if there is any piece of equipment out there that will do
this?

I think this is what you're looking for:

http://www.harborfreight.com/cpi/cta...emnumber=44094

Or if looking for a floor-standing model:

http://www.harborfreight.com/cpi/cta...emnumber=31980

I haven't used either so I can't comment on them. You might want to take a
look at them in a local HF store to see if they'll fit your needs.

Regards,
Michael

"TT" wrote in message
news:LRY3e.54389$Az.27198@lakeread02...
The only Diacro's I see are punch & die equipment.

-Tom

There aren't any of the type I'm talking about on ebay right now. We have
one at work, it's like a rotating table with posts to bend stuff around.



"ATP*" wrote in message
...

"TT" wrote in message
news:LYX3e.54379$Az.37205@lakeread02...
Before I build a brake for bending nice tight 90 deg. bends in 1/4"
round,
was wondering if there is any piece of equipment out there that will do
this?

Sounds like a Diacro, but you might want to check out HF if you can't
obtain
the Diacro

Was previously using a large Pexto brake but some numbnut tried to bend
3/8"
rebar and screwed it up and it's now signed "NO ROUND STOCK".

Thanks

-Tom