I have a newer home, built in 98, with one piece tub/shower units,
the tub has a single handled delta faucet that can be turned 180 degrees to
turn on the water.
well, the tub is not regularly used, and the faucet it leaking now.
I took the handle off, and the little guide that limits how far you can turn
the faucet.
Once the brass guide (or what ever it is called) is off, you can spin the
handle around 360 degree's continually.
I spun it all the way around hoping that it would stop the dripping /
running faucet. with no luck.

With the guide off I can adjust the handle to a point that has the water
dripping about 1 drop per second, (that's the best is does)
but, the valve is in a position that would prevent me from putting the guide
back on, I'm guessing that a washer of some type is damaged or worn out
inside the assembly, How do you get inside one of those faucets? it does
not seems like I can service it as it is all closed, or so it appears. Is
it possible to replace a seal inside the tap, and can I do it without
wrecking the tub unit?

Dave

"JimmySchmittsLovesChocolateMilk" wrote in message
...
I have a newer home, built in 98, with one piece tub/shower units,
the tub has a single handled delta faucet that can be turned 180 degrees
to turn on the water.
well, the tub is not regularly used, and the faucet it leaking now.
I took the handle off, and the little guide that limits how far you can
turn the faucet.
Once the brass guide (or what ever it is called) is off, you can spin the
handle around 360 degree's continually.
I spun it all the way around hoping that it would stop the dripping /
running faucet. with no luck.

With the guide off I can adjust the handle to a point that has the water
dripping about 1 drop per second, (that's the best is does)
but, the valve is in a position that would prevent me from putting the
guide back on, I'm guessing that a washer of some type is damaged or worn
out inside the assembly, How do you get inside one of those faucets? it
does not seems like I can service it as it is all closed, or so it
appears. Is it possible to replace a seal inside the tap, and can I do it
without wrecking the tub unit?

Dave



ooop,

Found my faucet at delta's site,
http://deltacom.deltafaucet.com/medi...67_v1_4689.pdf
this looks like it should cover everything I need,
any tips, to consider? looks like I've got it all figured out though.

Dave

"JimmySchmittsLovesChocolateMilk" wrote in message
...
ooop,

Found my faucet at delta's site,

http://deltacom.deltafaucet.com/medi...67_v1_4689.pdf
this looks like it should cover everything I need,
any tips, to consider? looks like I've got it all figured out though.


When you go to the hardware store to get the parts don't forget some
plumbers grease. The little tube of the stuff is probably a lifetime
supply, but it is worth it.

Also with the water off feel around inside the valve body for any rough
spots caused by calcium build up. If you got some, soak a paper towel in
vinegar and stuff in in the cavity for a while to soften it or dissolve it.
This is what usually eats the rubber seals. The plumbers grease helps the
calcium from sticking.

--

Roger Shoaf

About the time I had mastered getting the toothpaste back in the tube, then
they come up with this striped stuff.

JimmySchmittsLovesChocolateMilk wrote:
SNIP
Found my faucet at delta's site,
http://deltacom.deltafaucet.com/medi...67_v1_4689.pdf
this looks like it should cover everything I need,
any tips, to consider? looks like I've got it all figured out though.

With the (Main) water supply turned Off, turn the (Delta) bath faucet
ON. Then open other faucets at a lower level in the house to drain
off water in the pipes. That will help avoid nasty surprises when
you disassemble the Delta control, like water dripping down into
the wall...

Jim

"Speedy Jim" wrote in message
...
JimmySchmittsLovesChocolateMilk wrote:
SNIP
Found my faucet at delta's site,
http://deltacom.deltafaucet.com/medi...67_v1_4689.pdf
this looks like it should cover everything I need,
any tips, to consider? looks like I've got it all figured out though.

With the (Main) water supply turned Off, turn the (Delta) bath faucet
ON. Then open other faucets at a lower level in the house to drain
off water in the pipes. That will help avoid nasty surprises when
you disassemble the Delta control, like water dripping down into
the wall...

Jim

Thanks, I didn't think about that, I'll make sure to cut the water AND
kill the pressure before pulling the delta faucet all apart,
One thing I did notice, and was surprised about, is when I took off the
cover plate for the faucet, there was a breeze blowing into the tub thru
the opening in the shower wall. The faucet is on a an interior wall, is
this normal? I have a crawl space where all the pluming is run, and I'm
guessing at the air entering from the crawlspace into the wall where the
pipes pass thru the floor, or where the vent pipe leaves the top of the
wall. (single story)

I have one of these valves in my bathroom too. Mine has the 2 shutoff valves
(turned on/off with a screwdriver) that makes it very convenient to shut off
the water supply within the valve body before it enters the main knob/handle
operated valve. By shutting these off, you don't have to worry about all the
water in the pipes feeding the tub valve to drain out the valve chamber when
you remove the large cap. Mine is from 1987 and has the usual Delta springs
and rubber seats as wear items. Some (newer ones?) have an expensive plastic
cartridge that needs to be replaced. when the valve drips when shut.

Bob






"JimmySchmittsLovesChocolateMilk" wrote in message
...

"JimmySchmittsLovesChocolateMilk" wrote in message
...
I have a newer home, built in 98, with one piece tub/shower units,
the tub has a single handled delta faucet that can be turned 180 degrees
to turn on the water.
well, the tub is not regularly used, and the faucet it leaking now.
I took the handle off, and the little guide that limits how far you can
turn the faucet.
Once the brass guide (or what ever it is called) is off, you can spin
the handle around 360 degree's continually.
I spun it all the way around hoping that it would stop the dripping /
running faucet. with no luck.

With the guide off I can adjust the handle to a point that has the water
dripping about 1 drop per second, (that's the best is does)
but, the valve is in a position that would prevent me from putting the
guide back on, I'm guessing that a washer of some type is damaged or
worn out inside the assembly, How do you get inside one of those
faucets? it does not seems like I can service it as it is all closed,
or so it appears. Is it possible to replace a seal inside the tap, and
can I do it without wrecking the tub unit?

Dave



ooop,

Found my faucet at delta's site,
http://deltacom.deltafaucet.com/medi...67_v1_4689.pdf
this looks like it should cover everything I need,
any tips, to consider? looks like I've got it all figured out though.

Dave

"Roger Shoaf" wrote in message
...


snip
Also with the water off feel around inside the valve body for any rough
spots caused by calcium build up. If you got some, soak a paper towel in
vinegar and stuff in in the cavity for a while to soften it or dissolve
it.
This is what usually eats the rubber seals. The plumbers grease helps the
calcium from sticking.

--

Roger Shoaf

About the time I had mastered getting the toothpaste back in the tube,
then
they come up with this striped stuff.


Roger, just wanted to say thanks for that little tip about the vinegar,
it worked great, there was some build up on the internal parts due to lack
of use and the vinegar cleaned it all up nice.
works great again,
thanks

Dave