Home Repair (alt.home.repair) For all homeowners and DIYers with many experienced tradesmen. Solve your toughest home fix-it problems.

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
  #1   Report Post  
Yaofeng
 
Posts: n/a
Default Toilet

A few years ago, oh.. I think probably 6 or 7 years ago, I fixed the
plumbing of this toilet in a rental I owned. Or so do I think. This
is the downstairs unit of a two family house which was built in the
1940's, it not earlier.

The lead bend on the waste pipe was leaking. I removed the toilet.
Chipped out a portion of the mosaic tile foor to get to the lead bend.
I did not remove the lead bend completely. Just saw cut it and left
a stub hanging out from the branch of cast iron stack. Then I wrapped
the stub with a rubber connector with stainless steel straps and
connect the upstream end with PVC pipe and bend. I took the
opportunity to retile the bathroom with 8x8 ceramic tiles also.

Six or seven years later tenants are complaining the toilet is
difficult to flush. But the rubber connection I made still hold as
there is no leak. So after eating turkey I am going to remove the
toilet to see what may have caused the plug as the tenants have gone
home for the holiday.

Anyone has this experience or care to speculate what I may find?
  #2   Report Post  
Pat
 
Posts: n/a
Default

I have found all sorts of objects stuck in the toilet.


  #3   Report Post  
Colbyt
 
Posts: n/a
Default


"Yaofeng" wrote in message
om...
A few years ago, oh.. I think probably 6 or 7 years ago, I fixed the
plumbing of this toilet in a rental I owned. Or so do I think. This
is the downstairs unit of a two family house which was built in the
1940's, it not earlier.

The lead bend on the waste pipe was leaking. I removed the toilet.
Chipped out a portion of the mosaic tile foor to get to the lead bend.
I did not remove the lead bend completely. Just saw cut it and left
a stub hanging out from the branch of cast iron stack. Then I wrapped
the stub with a rubber connector with stainless steel straps and
connect the upstream end with PVC pipe and bend. I took the
opportunity to retile the bathroom with 8x8 ceramic tiles also.

Six or seven years later tenants are complaining the toilet is
difficult to flush. But the rubber connection I made still hold as
there is no leak. So after eating turkey I am going to remove the
toilet to see what may have caused the plug as the tenants have gone
home for the holiday.

Anyone has this experience or care to speculate what I may find?


I doubt that the work you did is the cause of the current problem. Observe
the problem for yourself before you tear anything apart. Flush it with and
without a load. If your turkey hasn't kicked in use about 15 squares total
of tissue in 3 clumps for a simulated load. Look for a calcium buildup
(brown scale) in the throat of the bowl or where the water enters around the
rim of the bowl. If buildup is present you can use muriatic acid to remove
it in several repeated treatments pouring about a quart into the bowl and
letting it sit for 30 minutes or so. MAKE SURE TO OPEN THE WINDOW! and wear
eye protection.

A flapper that closes to soon or a low water level in the tank are the most
likely causes if there is no buildup. Another possible cause is a blocked
vent (the stack that goes up through the roof).

If there are kids in the house and there is no buildup ask what they might
have put down it. The damnest thing I ever fished out was a tablespoon.
Flushed fine with no load and stopped up every time with a load. Plastic
toys from Micky D's are almost impossible to fish out. I generally tell the
tenant I buy and replace the unit and then we will break it open to see who
gets to pay for it. If it is a toy, they pay.

Colbyt


  #4   Report Post  
Red Neckerson
 
Posts: n/a
Default


"Yaofeng" wrote
A few years ago, oh.. I think probably 6 or 7 years ago, I fixed the
plumbing of this toilet in a rental I owned. Or so do I think. This
is the downstairs unit of a two family house which was built in the
1940's, it not earlier.

The lead bend on the waste pipe was leaking. I removed the toilet.
Chipped out a portion of the mosaic tile foor to get to the lead bend.
I did not remove the lead bend completely. Just saw cut it and left
a stub hanging out from the branch of cast iron stack. Then I wrapped
the stub with a rubber connector with stainless steel straps and
connect the upstream end with PVC pipe and bend. I took the
opportunity to retile the bathroom with 8x8 ceramic tiles also.

Six or seven years later tenants are complaining the toilet is
difficult to flush. But the rubber connection I made still hold as
there is no leak. So after eating turkey I am going to remove the
toilet to see what may have caused the plug as the tenants have gone
home for the holiday.

Anyone has this experience or care to speculate what I may find?


Jimmy Hoffa?


Reply
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules

Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
HELP... water leak at base of toilet when showering Steve Home Repair 11 February 22nd 18 06:29 PM
How to add basement toilet? Borrall Wonnell Home Repair 3 November 4th 04 06:27 AM
toilet makes other toilet flush Spitfire 1500 Home Repair 3 June 7th 04 04:28 AM
Run on toilet paper predicted Stormin Mormon Home Repair 12 October 30th 03 08:48 PM


All times are GMT +1. The time now is 01:13 PM.

Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 DIYbanter.
The comments are property of their posters.
 

About Us

"It's about DIY & home improvement"