replying to 2 door, Nikki ll wrote:
none wrote:

"Harry Avant" wrote in message
...
Lint filter doesn't stay free of debris, guess what happens?
I'm also curious why you would want to filter waste water. Seems to me, it
would be like wanting to filter toilet water. Sewers are there for a
purpose.



live in florida, have 2 septic tanks, one is for gray water which
receives the kitchen sink and laundry discharge, the lines ( which Y
together ) under the slab for the gray water is 2 inch PVC. every two
years without fail I have had to have Roto Rooter or some other drain
cleaning company clean out the pipe under the slab because of pet / human
hair and lint. always over a hundred dollars, the last clean out the
plumber said why don't you put ladies nylon hose over drain hose and
clamp it on being sure to check it each week after laundry day. I am an
elderly woman, sure was relieved I could do it myself and not have to
write that big check every other year. He also said it would keep build
up out of septic tank which is a greater expense to clean.


--

On 6/6/2014 9:44 AM, Nikki ll wrote:
replying to 2 door, Nikki ll wrote:
none wrote:

"Harry Avant" wrote in message
...
Lint filter doesn't stay free of debris, guess what happens?
I'm also curious why you would want to filter waste water. Seems to
me, it would be like wanting to filter toilet water. Sewers are there
for a purpose.



live in florida, have 2 septic tanks, one is for gray water which
receives the kitchen sink and laundry discharge, the lines ( which Y
together ) under the slab for the gray water is 2 inch PVC. every two
years without fail I have had to have Roto Rooter or some other drain
cleaning company clean out the pipe under the slab because of pet / human
hair and lint. always over a hundred dollars, the last clean out the
plumber said why don't you put ladies nylon hose over drain hose and
clamp it on being sure to check it each week after laundry day. I am an
elderly woman, sure was relieved I could do it myself and not have to
write that big check every other year. He also said it would keep build
up out of septic tank which is a greater expense to clean.

That story also means the PVC pipes were most likely put in backwards so
there is a sharp end collecting the lint. Several years ago I had to
have a septic system completely rebuilt because it was put in by a moron
contractor. My neighbor doing the work pointed out the incorrect order
of the 4inch PVC going to the septic tank.

Bet you have the same problem, but there is no way to correct it.

Paul

Nikki:

You can do a lot better than a piece of hosiery wrapped around the end of your washer's discharge hose.

Any place that deals with agricultural spraying equipment will sell "inline strainers" like the kind shown in the photo below:

http://www.vacmotion.com/images/Stra...nersBottom.png

Basically, you simply splice the inline strainer right into your washer's discharge hose, and clean it every so often. To clean it, you simply unscrew the cup off the bottom of the strainer and remove the cylindrical strainer screen. Clean the screen in a pail of water, or just let it dry out and brush the lint off of it with an old toothbrush when it's dry, put it back into the inline strainer and screw the cup housing back on.

The advantage of an inline strainer are many:
1. it has much more surface area than you'd get by simply putting a sock over the end of your discharge hose, so you wouldn't need to clean the strainer nearly as often.
2. the cylindrical strainers come in various mesh sizes and the wire mesh is made of stainless steel, so each strainer will last much longer.
3. You can buy replacement strainers as parts, so you can have one inside the inline strainer while the other one is drying out for cleaning.

You don't need to be a plumber to splice an inline strainer into the discharge hose of your washing machine, and anyone at the agricultural spraying store that sells you the strainer will also be able to supply you with the necessary fittings to splice the strainer into your washer's discharge hose.

If you choose the go the hosiery route, I'd use one whole nylon leg. Drop the nylon into your washer's standpipe, fold the top of the nylon over the top of the stand pipe so the nylon mesh is on the OUTSIDE of the stand pipe and put a clamp on the stand pipe and tighten it up to hold the nylon in place. I'd be concerned about using the nylon because if it tears, it could end up clogging up that drain pipe. That would never happen with an inline strainer. Also, if you get an inline strainer with a transparent cup, you'll be able to see how badly the strainer needs cleaning.

nestork wrote:
Nikki:

You can do a lot better than a piece of hosiery wrapped around the end
of your washer's discharge hose.

Any place that deals with agricultural spraying equipment will sell
"inline strainers" like the kind shown in the photo below:

http://www.vacmotion.com/images/Stra...nersBottom.png

Basically, you simply splice the inline strainer right into your
washer's discharge hose, and clean it every so often. To clean it, you
simply unscrew the cup off the bottom of the strainer and remove the
cylindrical strainer screen. Clean the screen in a pail of water, or
just let it dry out and brush the lint off of it with an old toothbrush
when it's dry, put it back into the inline strainer and screw the cup
housing back on.

The advantage of an inline strainer are many:
1. it has much more surface area than you'd get by simply putting a sock
over the end of your discharge hose, so you wouldn't need to clean the
strainer nearly as often.
2. the cylindrical strainers come in various mesh sizes and the wire
mesh is made of stainless steel, so each strainer will last much
longer.
3. You can buy replacement strainers as parts, so you can have one
inside the inline strainer while the other one is drying out for
cleaning.

You don't need to be a plumber to splice an inline strainer into the
discharge hose of your washing machine, and anyone at the agricultural
spraying store that sells you the strainer will also be able to supply
you with the necessary fittings to splice the strainer into your
washer's discharge hose.

If you choose the go the hosiery route, I'd use one whole nylon leg.
Drop the nylon into your washer's standpipe, fold the top of the nylon
over the top of the stand pipe so the nylon mesh is on the OUTSIDE of
the stand pipe and put a clamp on the stand pipe and tighten it up to
hold the nylon in place. I'd be concerned about using the nylon because
if it tears, it could end up clogging up that drain pipe. That would
never happen with an inline strainer. Also, if you get an inline
strainer with a transparent cup, you'll be able to see how badly the
strainer needs cleaning.


Not everyone has a standpipe. This device works quite well in a utility
sink. This is what I use.

http://www.linttrapper.com/design/im...apper_item.jpg

On 6/6/2014 7:07 PM, DerbyDad03 wrote:
nestork wrote:
Nikki:

You can do a lot better than a piece of hosiery wrapped around the end
of your washer's discharge hose.

Any place that deals with agricultural spraying equipment will sell
"inline strainers" like the kind shown in the photo below:

http://www.vacmotion.com/images/Stra...nersBottom.png

Basically, you simply splice the inline strainer right into your
washer's discharge hose, and clean it every so often. To clean it, you
simply unscrew the cup off the bottom of the strainer and remove the
cylindrical strainer screen. Clean the screen in a pail of water, or
just let it dry out and brush the lint off of it with an old toothbrush
when it's dry, put it back into the inline strainer and screw the cup
housing back on.

The advantage of an inline strainer are many:
1. it has much more surface area than you'd get by simply putting a sock
over the end of your discharge hose, so you wouldn't need to clean the
strainer nearly as often.
2. the cylindrical strainers come in various mesh sizes and the wire
mesh is made of stainless steel, so each strainer will last much
longer.
3. You can buy replacement strainers as parts, so you can have one
inside the inline strainer while the other one is drying out for
cleaning.

You don't need to be a plumber to splice an inline strainer into the
discharge hose of your washing machine, and anyone at the agricultural
spraying store that sells you the strainer will also be able to supply
you with the necessary fittings to splice the strainer into your
washer's discharge hose.

If you choose the go the hosiery route, I'd use one whole nylon leg.
Drop the nylon into your washer's standpipe, fold the top of the nylon
over the top of the stand pipe so the nylon mesh is on the OUTSIDE of
the stand pipe and put a clamp on the stand pipe and tighten it up to
hold the nylon in place. I'd be concerned about using the nylon because
if it tears, it could end up clogging up that drain pipe. That would
never happen with an inline strainer. Also, if you get an inline
strainer with a transparent cup, you'll be able to see how badly the
strainer needs cleaning.


Not everyone has a standpipe. This device works quite well in a utility
sink. This is what I use.

http://www.linttrapper.com/design/im...apper_item.jpg


Just a .jpg --- Have a URL?

John

On 6/6/2014 8:08 PM, John wrote:
On 6/6/2014 7:07 PM, DerbyDad03 wrote:
nestork wrote:
Nikki:

You can do a lot better than a piece of hosiery wrapped around the end
of your washer's discharge hose.

Any place that deals with agricultural spraying equipment will sell
"inline strainers" like the kind shown in the photo below:

http://www.vacmotion.com/images/Stra...nersBottom.png

Basically, you simply splice the inline strainer right into your
washer's discharge hose, and clean it every so often. To clean it, you
simply unscrew the cup off the bottom of the strainer and remove the
cylindrical strainer screen. Clean the screen in a pail of water, or
just let it dry out and brush the lint off of it with an old toothbrush
when it's dry, put it back into the inline strainer and screw the cup
housing back on.

The advantage of an inline strainer are many:
1. it has much more surface area than you'd get by simply putting a sock
over the end of your discharge hose, so you wouldn't need to clean the
strainer nearly as often.
2. the cylindrical strainers come in various mesh sizes and the wire
mesh is made of stainless steel, so each strainer will last much
longer.
3. You can buy replacement strainers as parts, so you can have one
inside the inline strainer while the other one is drying out for
cleaning.

You don't need to be a plumber to splice an inline strainer into the
discharge hose of your washing machine, and anyone at the agricultural
spraying store that sells you the strainer will also be able to supply
you with the necessary fittings to splice the strainer into your
washer's discharge hose.

If you choose the go the hosiery route, I'd use one whole nylon leg.
Drop the nylon into your washer's standpipe, fold the top of the nylon
over the top of the stand pipe so the nylon mesh is on the OUTSIDE of
the stand pipe and put a clamp on the stand pipe and tighten it up to
hold the nylon in place. I'd be concerned about using the nylon because
if it tears, it could end up clogging up that drain pipe. That would
never happen with an inline strainer. Also, if you get an inline
strainer with a transparent cup, you'll be able to see how badly the
strainer needs cleaning.


Not everyone has a standpipe. This device works quite well in a utility
sink. This is what I use.

http://www.linttrapper.com/design/im...apper_item.jpg


Just a .jpg --- Have a URL?

John

Never mind, found it.
thx

On Fri, 6 Jun 2014 22:49:04 +0200, nestork
wrote:


Nikki:

You can do a lot better than a piece of hosiery wrapped around the end
of your washer's discharge hose.

Any place that deals with agricultural spraying equipment will sell
"inline strainers" like the kind shown in the photo below:

http://www.vacmotion.com/images/Stra...nersBottom.png

My washing machine doesn't have any lint filter, only a lint chopper.

I've never seen it, but I've certainly seen a lot of lint come out,
chopped or not. I use another device because I don't want to clog the
check valve in my laundry sink drain pipe.

Do you think this device you recommend will go more than one load
without needing cleaning?

How many loads do you go, and do you have a separate cleanable lint
filter in your washing machine.

micky wrote:
On Fri, 6 Jun 2014 22:49:04 +0200, nestork
wrote:


Nikki:

You can do a lot better than a piece of hosiery wrapped around the
end of your washer's discharge hose.

Any place that deals with agricultural spraying equipment will sell
"inline strainers" like the kind shown in the photo below:

http://www.vacmotion.com/images/Stra...nersBottom.png

My washing machine doesn't have any lint filter, only a lint chopper.

I've never seen it, but I've certainly seen a lot of lint come out,
chopped or not. I use another device because I don't want to clog
the check valve in my laundry sink drain pipe.

Do you think this device you recommend will go more than one load
without needing cleaning?

How many loads do you go, and do you have a separate cleanable lint
filter in your washing machine.

A filter like that will drain slower as it gets plugged up, but has until you
get to the next load to drain the whole tub, which could be hours or days, so
it'll probably do the job. If the tub is full of water when you load the next
wash, you clean it first. If it plugs up completely, and the wash and rinse
cycles fill the tub, the water will go above the filter, and overflow down the
middle of it without filtering, if I see it correctly.

"Bob F" wrote:
micky wrote:
On Fri, 6 Jun 2014 22:49:04 +0200, nestork
wrote:


Nikki:

You can do a lot better than a piece of hosiery wrapped around the
end of your washer's discharge hose.

Any place that deals with agricultural spraying equipment will sell
"inline strainers" like the kind shown in the photo below:

http://www.vacmotion.com/images/Stra...nersBottom.png

My washing machine doesn't have any lint filter, only a lint chopper.

I've never seen it, but I've certainly seen a lot of lint come out,
chopped or not. I use another device because I don't want to clog
the check valve in my laundry sink drain pipe.

Do you think this device you recommend will go more than one load
without needing cleaning?

How many loads do you go, and do you have a separate cleanable lint
filter in your washing machine.

A filter like that will drain slower as it gets plugged up, but has until you
get to the next load to drain the whole tub, which could be hours or days, so
it'll probably do the job. If the tub is full of water when you load the next
wash, you clean it first. If it plugs up completely, and the wash and rinse
cycles fill the tub, the water will go above the filter, and overflow down the
middle of it without filtering, if I see it correctly.

There seems to be some confusion here.

Micky responded to nestork's post about an in-line filter, while you
described the concept behind the in _drain_ filter that I linked to.

BTW...there are at least three was to clean the in-drain filter. Sometimes
I just wrap my hand around the lint and slide it off without removing the
filter from the drain, toss it in the garbage, then rinse my hand.
Sometimes I pull filter out and give it a quick hard "snap" over the
garbage and the lint comes off. Every now and then I give it a good
rinsing, inside and out, after removing the majority of the lint.

One downside is that you sometimes have to rinse out the sink because the
slower draining water doesn't always wash everything towards the drain.

What's confusing me is why you guys have so much lint in the water coming out of your washer.

It seems to me that there will be SOME lint, the odd strand of thread and maybe a button or two a year, but there shouldn't be so much lint that the lint filter needs cleaning after every wash.