[Ook]

How easy/difficult is it to cut threads into 3/4 pipe that is in the
ground? I've dug around the pipes and have room to work. I want to cut
a section out of the pipe, thread the end, and screw a cap onto it. Is
this fairly easy to do while the pipe is in a hole in the ground? Or
is this way too much trouble, and maybe I need to think of some other
way to do this? The pipes are old - they have probably been in the
ground for decades, and are rusty, so I'm not even sure I could clean
them up enough to be able to thread them. I'm also not sure I could
unscrew them from the various fittings, they are so old and rusty -
I'm not sure what would happen if I tried to unscrew a section of pipe
from a tee, it is so old, and one mistake and I have no water until I
get it fixed right.

So having said all this - is it practical to thread 3/4 water pipes
(iron I'm guessing) that are in a hole in the ground?

[DD_BobK]

On May 28, 11:28*pm, Ook wrote:
How easy/difficult is it to cut threads into 3/4 pipe that is in the
ground? I've dug around the pipes and have room to work. I want to cut
a section out of the pipe, thread the end, and screw a cap onto it. Is
this fairly easy to do while the pipe is in a hole in the ground? Or
is this way too much trouble, and maybe I need to think of some other
way to do this? The pipes are old - they have probably been in the
ground for decades, and are rusty, so I'm not even sure I could clean
them up enough to be able to thread them. I'm also not sure I could
unscrew them from the various fittings, they are so old and rusty -
I'm not sure what would happen if I tried to unscrew a section of pipe
from a tee, it is so old, and one mistake and I have no water until I
get it fixed right.

So having said all this - is it practical to thread 3/4 water pipes
(iron I'm guessing) that are in a hole in the ground?

Yes, what you're wanting to do is possible.

With a fair amount difficulty you could use a hex pipe die (hard to
start & turn)
or an easier task with a ratchet threading die like ebay Item number:
330740178741.

Or clean up the pipe and use

http://www.farm-home.com/mn/v11_cata...~&SSAID=198698

along with a capped stub of 3/4" pipe.

since it appears that you're after a quick & dirty solution

cheers
Bob

[bob haller]

On May 29, 2:28*am, Ook wrote:
How easy/difficult is it to cut threads into 3/4 pipe that is in the
ground? I've dug around the pipes and have room to work

water or natural gas?

If its galvanized water pipe what are you trying to accomplish?

messing with the pipe ill no doubt create a leak

[Jim Elbrecht]

On Mon, 28 May 2012 23:28:22 -0700 (PDT), Ook
wrote:

How easy/difficult is it to cut threads into 3/4 pipe that is in the
ground? I've dug around the pipes and have room to work. I want to cut
a section out of the pipe, thread the end, and screw a cap onto it. Is
this fairly easy to do while the pipe is in a hole in the ground? Or
is this way too much trouble, and maybe I need to think of some other
way to do this? The pipes are old - they have probably been in the
ground for decades, and are rusty, so I'm not even sure I could clean
them up enough to be able to thread them. I'm also not sure I could
unscrew them from the various fittings, they are so old and rusty -
I'm not sure what would happen if I tried to unscrew a section of pipe
from a tee, it is so old, and one mistake and I have no water until I
get it fixed right.

The problem isn't that it is in the ground. The problem is that it is
old and rusty. Use the compression fitting Bob linked to get
things working again-- and replace the line while the weather is good.
[Lowes and Home depot won't carry them-- but a good plumbing supply
place ought to]

Jim

[Sonny]

Or clean up the pipe and use

http://www.farm-home.com/mn/v11_cata...tldr+PGF+00621...

along with a capped stub of 3/4" pipe.

since it appears that you're after a quick & dirty solution

cheers
Bob

I had no idea there was such a fitting - compression coupling. Good
to know, though I would likely rarely use one. Thanks.

Sonny

[Jim Elbrecht]

On Tue, 29 May 2012 05:47:35 -0700 (PDT), Sonny
wrote:


Or clean up the pipe and use

http://www.farm-home.com/mn/v11_cata...tldr+PGF+00621...

along with a capped stub of 3/4" pipe.

since it appears that you're after a quick & dirty solution

cheers
Bob

I had no idea there was such a fitting - compression coupling. Good
to know, though I would likely rarely use one. Thanks.

It is like those sharkbites--- Hate to use them as a general rule,
but sometimes they just can't be beat.

Jim

[dpb]

On 5/29/2012 1:28 AM, Ook wrote:
How easy/difficult is it to cut threads into 3/4 pipe that is in the
ground? I've dug around the pipes and have room to work. I want to cut
a section out of the pipe, thread the end, and screw a cap onto it. Is
this fairly easy to do while the pipe is in a hole in the ground? Or
is this way too much trouble, and maybe I need to think of some other
way to do this? The pipes are old - they have probably been in the
ground for decades, and are rusty, so I'm not even sure I could clean
them up enough to be able to thread them. I'm also not sure I could
unscrew them from the various fittings, they are so old and rusty -
I'm not sure what would happen if I tried to unscrew a section of pipe
from a tee, it is so old, and one mistake and I have no water until I
get it fixed right.

So having said all this - is it practical to thread 3/4 water pipes
(iron I'm guessing) that are in a hole in the ground?

The compression fitting shown is a possibility.

Have much old galvanized water line here on the farmstead; some dating
probably back to the 30s or maybe even earlier--latest is late 50s to
early 60s so have a fair amount of practice here...

The biggest problem is just how badly pitted it actually is--if bad
enough, even the compression fitting gasket may not hold leak-free
although it'll undoubtedly be able to get you by for a while so can be
w/ water.

If inspection brings you to conclusion pipe is basically sound, the best
"trick" I've found for breaking loose an old fitting is heat--you'll
need a acetylene torch or other very good heat source; a propane hand
bottle won't do it. Go back to the tee or elbow or wherever and heat
the fitting and the thermal expansion will loosen the scale. _ALWAYS_
wear eye protection and cover up; the scale can pop and throw dirt
fragments, etc.

Also be sure to use two wrenches to back up the fitting--do not rely on
the pipe in place in the tee to restrain the joint while breaking it loose.

You'll need a hefty wrench and room to use it or you'll need to be stout
yourself. The "reach to the bottom of the hole laying on the ground and
try to tug at arms' length act" won't cut it...

--

[[email protected]]

On Mon, 28 May 2012 23:28:22 -0700 (PDT), Ook
wrote:

How easy/difficult is it to cut threads into 3/4 pipe that is in the
ground? I've dug around the pipes and have room to work. I want to cut
a section out of the pipe, thread the end, and screw a cap onto it. Is
this fairly easy to do while the pipe is in a hole in the ground? Or
is this way too much trouble, and maybe I need to think of some other
way to do this? The pipes are old - they have probably been in the
ground for decades, and are rusty, so I'm not even sure I could clean
them up enough to be able to thread them. I'm also not sure I could
unscrew them from the various fittings, they are so old and rusty -
I'm not sure what would happen if I tried to unscrew a section of pipe
from a tee, it is so old, and one mistake and I have no water until I
get it fixed right.

So having said all this - is it practical to thread 3/4 water pipes
(iron I'm guessing) that are in a hole in the ground?
Mabee not impossible, but definitely ompractical. Get back to a
solid fitting - even if it means going back to the shutoff or meter,
and go from there.

[Vic Smith]

On Mon, 28 May 2012 23:28:22 -0700 (PDT), Ook
wrote:

How easy/difficult is it to cut threads into 3/4 pipe that is in the
ground? I've dug around the pipes and have room to work. I want to cut
a section out of the pipe, thread the end, and screw a cap onto it. Is
this fairly easy to do while the pipe is in a hole in the ground? Or
is this way too much trouble, and maybe I need to think of some other
way to do this? The pipes are old - they have probably been in the
ground for decades, and are rusty, so I'm not even sure I could clean
them up enough to be able to thread them. I'm also not sure I could
unscrew them from the various fittings, they are so old and rusty -
I'm not sure what would happen if I tried to unscrew a section of pipe
from a tee, it is so old, and one mistake and I have no water until I
get it fixed right.

So having said all this - is it practical to thread 3/4 water pipes
(iron I'm guessing) that are in a hole in the ground?

Rusty pipe doesn't take to threading well.
I haven't been following this closely, but if somebody hasn't already
said it, you should be thinking about putting a new line to your
house, and abandoning all that buried pipe.
All of it.

But if you insist on fooling with that old pipe, I'd cut it away about
4 inches from the T, then crank the 4 inch piece out of the T.
The internal threads on a T hold up better than the outside of the
pipe.
Get a wrench sideways on the T to counter the force you use to crank
out the cut piece. Take up the slack on that with one hand, and apply
enough muscle so that wrench won't move as you crank.
Put a capped nipple on, using plenty of teflon tape.
But you need a backup plan if it goes wrong.
And that's putting a new line to your house, and abandoning all that
buried pipe.
So maybe just use the backup plan as the primary plan, and get ahead
of the game.

--
Vic

[EXT]

"Ook" wrote in message
...
How easy/difficult is it to cut threads into 3/4 pipe that is in the
ground? I've dug around the pipes and have room to work. I want to cut
a section out of the pipe, thread the end, and screw a cap onto it. Is
this fairly easy to do while the pipe is in a hole in the ground? Or
is this way too much trouble, and maybe I need to think of some other
way to do this? The pipes are old - they have probably been in the
ground for decades, and are rusty, so I'm not even sure I could clean
them up enough to be able to thread them. I'm also not sure I could
unscrew them from the various fittings, they are so old and rusty -
I'm not sure what would happen if I tried to unscrew a section of pipe
from a tee, it is so old, and one mistake and I have no water until I
get it fixed right.

So having said all this - is it practical to thread 3/4 water pipes
(iron I'm guessing) that are in a hole in the ground?

Perfect opportunity to buy another tool. I saw that a number of companies
make an electric portable hand held pipe threader. It would be perfect to
use in a cramped location such as a hole in the ground. Just Google, and you
will find them a little pricey, but even some discounters have some cheaper
ones.

[Attila.Iskander]

"Ook" wrote in message
...
How easy/difficult is it to cut threads into 3/4 pipe that is in the
ground? I've dug around the pipes and have room to work. I want to cut
a section out of the pipe, thread the end, and screw a cap onto it. Is
this fairly easy to do while the pipe is in a hole in the ground? Or
is this way too much trouble, and maybe I need to think of some other
way to do this? The pipes are old - they have probably been in the
ground for decades, and are rusty, so I'm not even sure I could clean
them up enough to be able to thread them. I'm also not sure I could
unscrew them from the various fittings, they are so old and rusty -
I'm not sure what would happen if I tried to unscrew a section of pipe
from a tee, it is so old, and one mistake and I have no water until I
get it fixed right.

So having said all this - is it practical to thread 3/4 water pipes
(iron I'm guessing) that are in a hole in the ground?

If it's just to cap the pipe, wit no future use.
Why not just fill the cap with epoxy and glue it to the pipe ?

[bob haller]

On May 30, 9:43*am, "Attila.Iskander"
wrote:
"Ook" wrote in message

...

How easy/difficult is it to cut threads into 3/4 pipe that is in the
ground? I've dug around the pipes and have room to work. I want to cut
a section out of the pipe, thread the end, and screw a cap onto it. Is
this fairly easy to do while the pipe is in a hole in the ground? Or
is this way too much trouble, and maybe I need to think of some other
way to do this? The pipes are old - they have probably been in the
ground for decades, and are rusty, so I'm not even sure I could clean
them up enough to be able to thread them. I'm also not sure I could
unscrew them from the various fittings, they are so old and rusty -
I'm not sure what would happen if I tried to unscrew a section of pipe
from a tee, it is so old, and one mistake and I have no water until I
get it fixed right.

So having said all this - is it practical to thread 3/4 water pipes
(iron I'm guessing) that are in a hole in the ground?

If it's just to cap the pipe, wit no future use.
Why not just fill the cap with epoxy and glue it to the pipe ?

messing with old galvanized is just wasting your time. even if you get
it to work it having been disturbed will leak again....

PEX is so cheap its a no brainer to use

[Ook]

Rusty pipe doesn't take to threading well.
I haven't been following this closely, but if somebody hasn't already
said it, you should be thinking about putting a new line to your
house, and abandoning all that buried pipe.
All of it.

snip

Yup - that is what I'm doing. Finally figured out that if I did find
the leak it would be very difficult to fix. Can't use a compression
fitting, the pipe is too old and pitted. And if it's a split fitting,
what do you do? You can't just unscrew it and screw a new on it. Can't
thread this old rusty pitted pipe, not easily at least - too much
trouble for me to have a go at it.

So today I get a nice new copper water pipe from meter to house, and
the rest of the old pipe can just sit there and rot for all I care.

[HerHusband]

Yup - that is what I'm doing. Finally figured out that if I did find
the leak it would be very difficult to fix. Can't use a compression
fitting, the pipe is too old and pitted. And if it's a split fitting,
what do you do? You can't just unscrew it and screw a new on it. Can't
thread this old rusty pitted pipe, not easily at least - too much
trouble for me to have a go at it.

When I need to repair a leak in threaded pipe, I have always worked back to
the next fitting and installed new pipe from there. Unfortunately, if one
section is bad, the rest is usually not far behind. The first leak or two I
had to work back 10 to 20 feet to get to metal solid enough to work with.
Eventually, I had to take out so much galvanized pipe, it was faster and
easier to just replace the entire plumbing system with CPVC pipe.

My in-laws recently had their galvanized supply line break underground. It
created a sink hole in the yard and a real mess in the basement. We had to
have the fire department come out and shut off the water so we could work
on it. Thankfully, the break was next to a fitting just a couple feet from
the basement wall. I was able to remove the broken fitting, clean up the
threads, and thread on a CPVC adapter. Then I ran CPVC into the house.
Someday I'm sure we'll have to replace the rest of the water line out to
the street, but it worked OK for an emergency fix.

So today I get a nice new copper water pipe from meter to house, and
the rest of the old pipe can just sit there and rot for all I care.

That is the best approach if you have the time to do it. Copper wouldn't be
a good choice in our area as our soil is very acidic. It wouldn't take long
to corrode a buried copper pipe. I prefer PVC pipe for buried lines, but
the black poly pipe works well too.

Anthony