Home |
Search |
Today's Posts |
|
Home Repair (alt.home.repair) For all homeowners and DIYers with many experienced tradesmen. Solve your toughest home fix-it problems. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
|
#1
Posted to alt.home.repair
|
|||
|
|||
Where to run the wire....
Installing a 10K BTU A/C (8A) for a relative. The outlet to be used is on
the far end of a daisy chain of a half-dozen other outlets and two ceiling lights. It looks like I'll be running a dedicated wire for this outlet. The outlet in question is two feet from an exterior corner, and about a foot off of the ground. All of the wires in the house go up from the breaker box, and route around in the attic to whatever header they drop down from. There isn't a wire coming out of the header above the outlet in question (nor the adjacent one), leading me to believe it goes horizontal through it's daisy chain. If I run the wire up to the attic, I have to fish through wall insulation, a firebreak, and the header, which has about 10" of working room in the attic. Did I mention the 18" of blown insulation? If I drop the wire down to the crawl space, I have to make a 90 degree bend in the 4"x6" footer (down from above, into from below), and will have to cut out two kicker panels for work access (one below the outlet and one below the breaker box in the utility room). I'm thinking my best bet will be to run the wire down. *What I usually do when there is limited attic access is cut a hole in the wall (Using my 45 degree cut technique) close to the ceiling and drill up into the attic. The hole in the wall should be big enough so that your drill will fit inside so you can at least drill straight and not angled towards the outside. I push a fishtape up several feet into the attic. I then go up in the attic with a fiberglass rod with a hook on it and grab the fishtape. I pull the wire down from the attic. Fiberglass rods go through insulated walls better than a fishtape. However you will need to cut a hole and drill through that fire block so a fishtape might suffice. Use 12/2 for the A/C line. I would cut in a separate box for the A/C and leave the existing boxes and wiring alone. |
#2
Posted to alt.home.repair
|
|||
|
|||
Where to run the wire....
John Grabowski wrote:
*What I usually do when there is limited attic access is cut a hole in the wall (Using my 45 degree cut technique) close to the ceiling and drill up into the attic. The hole in the wall should be big enough so that your drill will fit inside so you can at least drill straight and not angled towards the outside. I push a fishtape up several feet into the attic. I then go up in the attic with a fiberglass rod with a hook on it and grab the fishtape. I pull the wire down from the attic. Fiberglass rods go through insulated walls better than a fishtape. However you will need to cut a hole and drill through that fire block so a fishtape might suffice. Use 12/2 for the A/C line. I would cut in a separate box for the A/C and leave the existing boxes and wiring alone. You know, I've done the drill access at the footer before, but somehow I didn't carry the idea over to the header. Thanks! Jon |
#3
Posted to alt.home.repair
|
|||
|
|||
Where to run the wire....
On 5/20/2010 7:31 AM, Jon Danniken wrote:
John Grabowski wrote: *What I usually do when there is limited attic access is cut a hole in the wall (Using my 45 degree cut technique) close to the ceiling and drill up into the attic. The hole in the wall should be big enough so that your drill will fit inside so you can at least drill straight and not angled towards the outside. I push a fishtape up several feet into the attic. I then go up in the attic with a fiberglass rod with a hook on it and grab the fishtape. I pull the wire down from the attic. Fiberglass rods go through insulated walls better than a fishtape. However you will need to cut a hole and drill through that fire block so a fishtape might suffice. Use 12/2 for the A/C line. I would cut in a separate box for the A/C and leave the existing boxes and wiring alone. You know, I've done the drill access at the footer before, but somehow I didn't carry the idea over to the header. Thanks! Jon I'd just plug it into the existing outlet and be done. You stated in the original message it was only 8a. Even on a 15a circuit, this still leaves plenty for the 'couple o' lights' and the other outlets. Unless it's a microwave plugged into the other outlets, you will never know the difference. -- Steve Barker remove the "not" from my address to email |
#4
Posted to alt.home.repair
|
|||
|
|||
Where to run the wire....
Steve Barker wrote:
On 5/20/2010 7:31 AM, Jon Danniken wrote: John Grabowski wrote: *What I usually do when there is limited attic access is cut a hole in the wall (Using my 45 degree cut technique) close to the ceiling and drill up into the attic. The hole in the wall should be big enough so that your drill will fit inside so you can at least drill straight and not angled towards the outside. I push a fishtape up several feet into the attic. I then go up in the attic with a fiberglass rod with a hook on it and grab the fishtape. I pull the wire down from the attic. Fiberglass rods go through insulated walls better than a fishtape. However you will need to cut a hole and drill through that fire block so a fishtape might suffice. Use 12/2 for the A/C line. I would cut in a separate box for the A/C and leave the existing boxes and wiring alone. You know, I've done the drill access at the footer before, but somehow I didn't carry the idea over to the header. Thanks! Jon I'd just plug it into the existing outlet and be done. You stated in the original message it was only 8a. Even on a 15a circuit, this still leaves plenty for the 'couple o' lights' and the other outlets. Unless it's a microwave plugged into the other outlets, you will never know the difference. The vacuum could be a problem. |
#5
Posted to alt.home.repair
|
|||
|
|||
Where to run the wire....
On 5/20/2010 9:27 AM, Bob F wrote:
Steve Barker wrote: On 5/20/2010 7:31 AM, Jon Danniken wrote: John Grabowski wrote: *What I usually do when there is limited attic access is cut a hole in the wall (Using my 45 degree cut technique) close to the ceiling and drill up into the attic. The hole in the wall should be big enough so that your drill will fit inside so you can at least drill straight and not angled towards the outside. I push a fishtape up several feet into the attic. I then go up in the attic with a fiberglass rod with a hook on it and grab the fishtape. I pull the wire down from the attic. Fiberglass rods go through insulated walls better than a fishtape. However you will need to cut a hole and drill through that fire block so a fishtape might suffice. Use 12/2 for the A/C line. I would cut in a separate box for the A/C and leave the existing boxes and wiring alone. You know, I've done the drill access at the footer before, but somehow I didn't carry the idea over to the header. Thanks! Jon I'd just plug it into the existing outlet and be done. You stated in the original message it was only 8a. Even on a 15a circuit, this still leaves plenty for the 'couple o' lights' and the other outlets. Unless it's a microwave plugged into the other outlets, you will never know the difference. The vacuum could be a problem. Not if you plug it in a different circuit. Or turn the air off whilst doing such things. -- Steve Barker remove the "not" from my address to email |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
S Plan Zone Valve Grey Wire To Brown Wire? | UK diy | |||
connecting smaller stranded wire to heavier solid wire? | Home Repair | |||
Stripping 40 AWG/45 SWG or finer magnet wire/enamelled copper wire? | Electronics Repair | |||
el wire rope lighting electroluminescent FLEXIBLE NEON WIRE (KPT SERIES) | Home Repair | |||
el wire rope lighting electroluminescent FLEXIBLE NEON WIRE (KPT SERIES) | Home Repair |