Hi,

I was using my Eureka Boss vacuum cleaner when it started making
a horrible flapping noise. Shut it off and started it again. Same
noise. Took it apart, cleaned some hair out of the beater bar. Started
it and it was quieter for about 3 seconds, then the horrible noise
started again. Replaced the belt, which was old and stretched. Ran
quiet for 2 seconds, then the horrible noise came back.

It's a "card in the bicycle spokes" kind of sound.

There is also a strange smell from the vacuum when this happens.

It's about 10 to 15 years old, so time to toss, possibly, but would
prefer to fix it if possible.

Any clues welcome.


Thanks

On Nov 16, 12:31 am, utilitarian wrote:
Hi,

I was using my Eureka Boss vacuum cleaner when it started making
a horrible flapping noise. Shut it off and started it again. Same
noise. Took it apart, cleaned some hair out of the beater bar. Started
it and it was quieter for about 3 seconds, then the horrible noise
started again. Replaced the belt, which was old and stretched. Ran
quiet for 2 seconds, then the horrible noise came back.

It's a "card in the bicycle spokes" kind of sound.

There is also a strange smell from the vacuum when this happens.

It's about 10 to 15 years old, so time to toss, possibly, but would
prefer to fix it if possible.

Any clues welcome.

Thanks

I should add that the beater brush spins just fine during all this.

On Nov 16, 4:13*am, utilitarian wrote:
On Nov 16, 12:31 am, utilitarian wrote:





Hi,

* * *I was using my Eureka Boss vacuum cleaner when it started making
a horrible flapping noise. *Shut it off and started it again. Same
noise. Took it apart, cleaned some hair out of the beater bar. Started
it and it was quieter for about 3 seconds, then the horrible noise
started again. Replaced the belt, which was old and stretched. Ran
quiet for 2 seconds, then the horrible noise came back.

It's a "card in the bicycle spokes" kind of sound.

There is also a strange smell from the vacuum when this *happens.

It's about 10 to 15 years old, so time to toss, possibly, but would
prefer to fix it if possible.

Any clues welcome.

Thanks

I should add that the beater brush spins just fine during all this.- Hide quoted text -

- Show quoted text -

Our Eureka is about 40 years old. The "strange smell" is often the
rubber belt slipping. However since the OPs has been replaced sounds
as if something such as a stone, or coin have got into the fan
section of the motor? It may be possible to shake it out withou taking
it apart.
However they are pretty simple to disassemble with very few tools.
Parts are often still available!

On Nov 16, 5:10*am, terry wrote:
On Nov 16, 4:13*am, utilitarian wrote:





On Nov 16, 12:31 am, utilitarian wrote:

Hi,

* * *I was using my Eureka Boss vacuum cleaner when it started making
a horrible flapping noise. *Shut it off and started it again. Same
noise. Took it apart, cleaned some hair out of the beater bar. Started
it and it was quieter for about 3 seconds, then the horrible noise
started again. Replaced the belt, which was old and stretched. Ran
quiet for 2 seconds, then the horrible noise came back.

It's a "card in the bicycle spokes" kind of sound.

There is also a strange smell from the vacuum when this *happens.

It's about 10 to 15 years old, so time to toss, possibly, but would
prefer to fix it if possible.

Any clues welcome.

Thanks

I should add that the beater brush spins just fine during all this.- Hide quoted text -

- Show quoted text -

Our Eureka is about 40 years old. The "strange smell" is often the
rubber belt slipping. However since the OPs has been replaced sounds
as if *something such as *a stone, or coin have got into the fan
section of the motor? It may be possible to shake it out withou taking
it apart.
However they are pretty simple to disassemble with very few tools.
Parts are often still available!- Hide quoted text -

- Show quoted text -

Oh btw hair tends to get caught around the ends of the beater bar.
Those ends can be removed, hair and other gubbins (cotton strands etc.
removed) the bearing ends lightly oiled or (even a bit of cooking oil
or hand cream!) and reassembled.

Nix the cooking oil. It rapidly grows rancid. Sticky, and
then worse than useless.

My fav is silicone spray, which doesn't attract dust.

--
Christopher A. Young
Learn more about Jesus
www.lds.org
..


"terry" wrote in message
...

Oh btw hair tends to get caught around the ends of the
beater bar.
Those ends can be removed, hair and other gubbins (cotton
strands etc.
removed) the bearing ends lightly oiled or (even a bit of
cooking oil
or hand cream!) and reassembled.

On Nov 16, 10:40*am, "Stormin Mormon"
wrote:
Nix the cooking oil. It rapidly grows rancid. Sticky, and
then worse than useless.

My fav is silicone spray, which doesn't attract dust.

--
Christopher A. Young
Learn more about Jesus
*www.lds.org
.

"terry" wrote in message

...

Oh btw hair tends to get caught around the ends of the
beater bar.
Those ends can be removed, hair and other gubbins (cotton
strands etc.
removed) *the bearing ends lightly oiled or (even a bit of
cooking oil
or hand cream!) and reassembled.

Agree on the cooking oil, but the little smear on the very small area
of bearing on end of the beater bar, not likely to be a problem. If
not that; something else 'greasy' around the house will often do! I
seem to remember using a dab of bacon fat once for something!
Relative rented an empty summer property couple of years ago, was sent
through the mail a brand new, never used key. Arriving at the location
rough edges of the new key meant that the young woman could not get
key into the lock, let alone turn it.
However by rubbing with a stone picked up off the ground and applying
a little hand cream she was able to get entry and after that the key
got more 'used' and worked fine. There is often a way!
Not even Maciver!

I forgot to mention my favorite fix. Take the vac outdoors,
and bring a power cord with you. Unzip the bag, and take the
inner disposable bag out. Work on the deck, or asphalt or
cement. Point the tube in a safe direction (out over the
lawn) and plug in the vac, turn it on. With the bag missing,
the vac should develop an incredible air flow past the
beater, and out the (unrestricted) tube. Sometimes that will
blow out all kinds of strange things.

You may have to leave the bag off, and shake the vac upside
down to get the item out of the fan, up the tube, and the
item falls on the ground.

--
Christopher A. Young
Learn more about Jesus
www.lds.org
..


"terry" wrote in message
...

Our Eureka is about 40 years old. The "strange smell" is
often the
rubber belt slipping. However since the OPs has been
replaced sounds
as if something such as a stone, or coin have got into the
fan
section of the motor? It may be possible to shake it out
withou taking
it apart.
However they are pretty simple to disassemble with very few
tools.
Parts are often still available!

Well, that changes everything. It's likely choking on a
TURKEY bone, then.

Please let us know what you find.

--
Christopher A. Young
Learn more about Jesus
www.lds.org
..


"utilitarian" wrote in message
...

I should add that the beater brush spins just fine during
all this.

Hard to describe in words. Flip the vac upside down and pull
the beater bar, again. The one end of the bar, there is a
tube where the air flow goes. Towards the back of the vacuum
(nearer to the handle) is a fan which blows the air and such
into the bag. Most likely there is a foreign object in the
fan. You may need a flashlight, and a long tweezers or
hemostat to get the foreigh object out.

It's choking on a chicken bone! Hack! Hack!

--
Christopher A. Young
Learn more about Jesus
www.lds.org
..


"utilitarian" wrote in message
...
Hi,

I was using my Eureka Boss vacuum cleaner when it
started making
a horrible flapping noise. Shut it off and started it
again. Same
noise. Took it apart, cleaned some hair out of the beater
bar. Started
it and it was quieter for about 3 seconds, then the horrible
noise
started again. Replaced the belt, which was old and
stretched. Ran
quiet for 2 seconds, then the horrible noise came back.

It's a "card in the bicycle spokes" kind of sound.

There is also a strange smell from the vacuum when this
happens.

It's about 10 to 15 years old, so time to toss, possibly,
but would
prefer to fix it if possible.

Any clues welcome.


Thanks

"utilitarian" wrote in message
...
Hi,

I was using my Eureka Boss vacuum cleaner when it started making
a horrible flapping noise. Shut it off and started it again. Same
noise. Took it apart, cleaned some hair out of the beater bar. Started
it and it was quieter for about 3 seconds, then the horrible noise
started again. Replaced the belt, which was old and stretched. Ran
quiet for 2 seconds, then the horrible noise came back.

It's a "card in the bicycle spokes" kind of sound.

There is also a strange smell from the vacuum when this happens.

It's about 10 to 15 years old, so time to toss, possibly, but would
prefer to fix it if possible.

Any clues welcome.


Thanks

Check the ball bearings on the motor shaft. This requires disassembly of
the motor, but just be careful and you should be OK.

I have had these bearings fail and it makes a noise similar to your
description. Good news is the bearings are cheap, bad news is they are
sometimes a bear to pull off the shaft.

--

Roger Shoaf

About the time I had mastered getting the toothpaste back in the tube, then
they come up with this striped stuff.