Home |
Search |
Today's Posts |
|
Home Repair (alt.home.repair) For all homeowners and DIYers with many experienced tradesmen. Solve your toughest home fix-it problems. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
|
#1
|
|||
|
|||
Troubleshooting garage door opener
After working fine for many years, my garage door opener is having
sporadic problems. Replacing it is going to be costly and problematic, so I want to take a shot at repairing it instead. Here are the symptoms: 1) The door will occasionally open or close on its own. 2) The hard-wired wall switch is occasionally unresponsive; pushing the button has no effect. 3) The remote control seems to work consistently; there's been no problem with the remote. From these symptoms, I suspected the wiring on the wall switch. (I tried the easy and obvious step of changing codes on the remote in case there was neighborhood interference, but this made no difference.) I replaced both the wire and the switch itself, but the symptoms continued. I then disconnected the wire for the switch completely, and operated the door by remote only for several days. Unfortunately, we still had the problem where the door would sporadically raise or lower on its own. I'm now thinking there's an electrical problem with the switch connections within the motor casing itself. I unbolted the unit from the ceiling, lowered it onto a ladder, and removed the cover for inspection, but I didn't find any obvious problems. Of course, I wouldn't know what to look for. Does it sound like I'm on the right track? How can I isolate what the problem might be? Thanks! |
#2
|
|||
|
|||
Most switches operate with a metal spring beam that makes contact when
you press the button. If the metal ribbon fatigues over time it will rest against the contact intermittenly and may make the garage door open and close. I had this exact problem with my remote. I would suspect the hard wired wall switch. |
#3
|
|||
|
|||
Agreed, which is why I replaced the switch, then disconnected it for a
period of time. Unfortunately, the symptoms continued during/after both of these tests. Hmmmm... wrote in news:1122769799.778093.214100 @g49g2000cwa.googlegroups.com: Most switches operate with a metal spring beam that makes contact when you press the button. If the metal ribbon fatigues over time it will rest against the contact intermittenly and may make the garage door open and close. I had this exact problem with my remote. I would suspect the hard wired wall switch. |
#4
|
|||
|
|||
Perhaps faulty wiring from the hard wired switch to the motor
|
#5
|
|||
|
|||
That sounds reasonable to me. Any idea how I can isolate the problem? I'm
not much of an electrician. wrote in news:1122778979.676812.214050 @g44g2000cwa.googlegroups.com: Perhaps faulty wiring from the hard wired switch to the motor |
#6
|
|||
|
|||
Dave N wrote:
That sounds reasonable to me. Any idea how I can isolate the problem? I'm not much of an electrician. Disconnect the wire at the opener. See if the problem goes away. Or just replace the wiring from the opener to the switch. It's 12-volt - nothing special. I bet some critter knawed part way through the wires causing shorts, opens, and drips. |
#7
|
|||
|
|||
In alt.home.repair on Sun, 31 Jul 2005 14:55:12 -0500 Dave N
posted: That sounds reasonable to me. Any idea how I can isolate the problem? I'm not much of an electrician. You said you replaced the wire from the switch. Now it seems you didn't. wrote in news:1122778979.676812.214050 : Perhaps faulty wiring from the hard wired switch to the motor Meirman -- If emailing, please let me know whether or not you are posting the same letter. Change domain to erols.com, if necessary. |
#8
|
|||
|
|||
|
#9
|
|||
|
|||
"Dave N" wrote in message .142... After working fine for many years, my garage door opener is having sporadic problems. Replacing it is going to be costly and problematic, so I want to take a shot at repairing it instead. Here are the symptoms: 1) The door will occasionally open or close on its own. 2) The hard-wired wall switch is occasionally unresponsive; pushing the button has no effect. 3) The remote control seems to work consistently; there's been no problem with the remote. From these symptoms, I suspected the wiring on the wall switch. (I tried the easy and obvious step of changing codes on the remote in case there was neighborhood interference, but this made no difference.) I replaced both the wire and the switch itself, but the symptoms continued. I then disconnected the wire for the switch completely, and operated the door by remote only for several days. Unfortunately, we still had the problem where the door would sporadically raise or lower on its own. I'm now thinking there's an electrical problem with the switch connections within the motor casing itself. I unbolted the unit from the ceiling, lowered it onto a ladder, and removed the cover for inspection, but I didn't find any obvious problems. Of course, I wouldn't know what to look for. Does it sound like I'm on the right track? How can I isolate what the problem might be? Thanks! Shouldn't have any thing to do with the hard wired switch, but are you located near a military base. The military recently took back and started using frequencies that garage door openers use. Sears recently posted a notice that some older openers would start having difficulties because of this. I seem to remember that they came up with a retrofit of some kind that would alleviate the problem. And of course, all new openers now use a different frequency. Tom. |
#10
|
|||
|
|||
Shouldn't have any thing to do with the hard wired switch, but are you located near a military base. The military recently took back and started using frequencies that garage door openers use. Sears recently posted a notice that some older openers would start having difficulties because of this. I seem to remember that they came up with a retrofit of some kind that would alleviate the problem. And of course, all new openers now use a different frequency. Tom. Ditto........find a way to eliminate the remote signal input. Remove and/or short the antenna if appropriate. Use the wired switch until you can reasonably say that a unwanted remote signal is the problem |
#11
|
|||
|
|||
|
#12
|
|||
|
|||
I can try removing or shorting the antenna, but it doesn't really fit the
symptoms. I did suspect some kind of frequency interference at first, but that wouldn't explain the problems with the hard-wired switch. And, since both problems started simultaneously, I believe they have to be related. |
#13
|
|||
|
|||
In alt.home.repair on Sun, 31 Jul 2005 14:57:17 -0500 Dave N
posted: I can try removing or shorting the antenna, but it doesn't really fit the symptoms. I did suspect some kind of frequency interference at first, but that wouldn't explain the problems with the hard-wired switch. And, since both problems started simultaneously, I believe they have to be related. Yes, I saw your further description. Meirman -- If emailing, please let me know whether or not you are posting the same letter. Change domain to erols.com, if necessary. |
#14
|
|||
|
|||
How old is this garage door opener? What model?
|
#15
|
|||
|
|||
I'm not sure how old it is; it was installed when I bought the house 8
years ago, and working fine until now. The house itself is 30 years old. The opener is a Blue Max brand, but I don't know the model. wrote in : How old is this garage door opener? What model? |
#16
|
|||
|
|||
Dave N wrote:
After working fine for many years, my garage door opener is having sporadic problems. Replacing it is going to be costly and problematic, so I want to take a shot at repairing it instead. Here are the symptoms: 1) The door will occasionally open or close on its own. 2) The hard-wired wall switch is occasionally unresponsive; pushing the button has no effect. 3) The remote control seems to work consistently; there's been no problem with the remote. From these symptoms, I suspected the wiring on the wall switch. (I tried the easy and obvious step of changing codes on the remote in case there was neighborhood interference, but this made no difference.) I replaced both the wire and the switch itself, but the symptoms continued. I then disconnected the wire for the switch completely, and operated the door by remote only for several days. Unfortunately, we still had the problem where the door would sporadically raise or lower on its own. I'm now thinking there's an electrical problem with the switch connections within the motor casing itself. I unbolted the unit from the ceiling, lowered it onto a ladder, and removed the cover for inspection, but I didn't find any obvious problems. Of course, I wouldn't know what to look for. Does it sound like I'm on the right track? How can I isolate what the problem might be? Thanks! I realize that you changed your code so this is a long shot but just for the heck of it walk around your neighborhood with your remote and see if you can open anyone else's garage door.......you might just find the problem. Don |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Two questions about security light above the garage door | Home Ownership | |||
Two questions about security light above the garage door | Home Repair | |||
Electrical problem in garage | Home Repair | |||
garage rebuilding and party wall agreements (long) | UK diy | |||
Building an Extension (Garage and Block Selection) | UK diy |