Electronics Repair (sci.electronics.repair) Discussion of repairing electronic equipment. Topics include requests for assistance, where to obtain servicing information and parts, techniques for diagnosis and repair, and annecdotes about success, failures and problems.

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
  #1   Report Post  
Jacques Carrier
 
Posts: n/a
Default Fluke DMM model 77 series I and II schematic request

Hi fellow techs,

I am looking for a schematic (or service manual) for this fine DMM.
The first one was zapped by a high voltage pulse from an electric fence.
The other one was zapped by a microwave HV cap. (over 200V).

Thanks for your help.

Jacques
  #2   Report Post  
Sam Goldwasser
 
Posts: n/a
Default

(Jacques Carrier) writes:

Hi fellow techs,

I am looking for a schematic (or service manual) for this fine DMM.
The first one was zapped by a high voltage pulse from an electric fence.
The other one was zapped by a microwave HV cap. (over 200V).


Don't they have lifetime warranty?

--- sam | Sci.Electronics.Repair FAQ Mirror:
http://repairfaq.ece.drexel.edu/
Repair | Main Table of Contents: http://repairfaq.ece.drexel.edu/REPAIR/
+Lasers | Sam's Laser FAQ: http://repairfaq.ece.drexel.edu/sam/lasersam.htm
| Mirror Sites: http://repairfaq.ece.drexel.edu/REPAIR/F_mirror.html

Note: These links are hopefully temporary until we can sort out the excessive
traffic on Repairfaq.org.

Important: Anything sent to the email address in the message header is ignored.
To contact me, please use the feedback form on the S.E.R FAQ Web sites.



  #3   Report Post  
Eric
 
Posts: n/a
Default

Jacques,

I am on training this week, I have the Fluke 70 series one service manual.
Inside the manual, it tell you the hints to troubleshoot. Let me know your
fax number and I will send the entire manual to you next week.

Good luck.

Eric
"Sam Goldwasser" wrote in message
...
(Jacques Carrier) writes:

Hi fellow techs,

I am looking for a schematic (or service manual) for this fine DMM.
The first one was zapped by a high voltage pulse from an electric fence.
The other one was zapped by a microwave HV cap. (over 200V).


Don't they have lifetime warranty?

--- sam | Sci.Electronics.Repair FAQ Mirror:

http://repairfaq.ece.drexel.edu/
Repair | Main Table of Contents: http://repairfaq.ece.drexel.edu/REPAIR/
+Lasers | Sam's Laser FAQ:

http://repairfaq.ece.drexel.edu/sam/lasersam.htm
| Mirror Sites:

http://repairfaq.ece.drexel.edu/REPAIR/F_mirror.html

Note: These links are hopefully temporary until we can sort out the

excessive
traffic on Repairfaq.org.

Important: Anything sent to the email address in the message header is

ignored.
To contact me, please use the feedback form on the S.E.R FAQ Web sites.





  #4   Report Post  
Eric
 
Posts: n/a
Default

Also, is there anyone has the 79 series II service manual can share, my
meter has inaccurate ohm reading and I would like to repair and recal.

Thanks

Eric

"Eric" wrote in message
...
Jacques,

I am on training this week, I have the Fluke 70 series one service manual.
Inside the manual, it tell you the hints to troubleshoot. Let me know

your
fax number and I will send the entire manual to you next week.

Good luck.

Eric
"Sam Goldwasser" wrote in message
...
(Jacques Carrier) writes:

Hi fellow techs,

I am looking for a schematic (or service manual) for this fine DMM.
The first one was zapped by a high voltage pulse from an electric

fence.
The other one was zapped by a microwave HV cap. (over 200V).


Don't they have lifetime warranty?

--- sam | Sci.Electronics.Repair FAQ Mirror:

http://repairfaq.ece.drexel.edu/
Repair | Main Table of Contents:

http://repairfaq.ece.drexel.edu/REPAIR/
+Lasers | Sam's Laser FAQ:

http://repairfaq.ece.drexel.edu/sam/lasersam.htm
| Mirror Sites:

http://repairfaq.ece.drexel.edu/REPAIR/F_mirror.html

Note: These links are hopefully temporary until we can sort out the

excessive
traffic on Repairfaq.org.

Important: Anything sent to the email address in the message header is

ignored.
To contact me, please use the feedback form on the S.E.R FAQ Web sites.







Reply
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules

Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
WARNING. DeWALT And Black and Decker Tools causing serious Injury and Death. Bob Woodworking 14 June 5th 04 09:22 AM
Dewalt Recalls? Marty Escarcega Metalworking 0 May 25th 04 12:17 PM


All times are GMT +1. The time now is 03:22 PM.

Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 DIYbanter.
The comments are property of their posters.
 

About Us

"It's about DIY & home improvement"