Home |
Search |
Today's Posts |
|
Electronics Repair (sci.electronics.repair) Discussion of repairing electronic equipment. Topics include requests for assistance, where to obtain servicing information and parts, techniques for diagnosis and repair, and annecdotes about success, failures and problems. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
#1
Posted to sci.electronics.repair
|
|||
|
|||
Who rewinds power XFRs?
I have a McIntosh MX110Z with a bad transformer. Any recommendations for rewinding? I've never done one and have no interest in trying. Thanks.
|
#2
Posted to sci.electronics.repair
|
|||
|
|||
Who rewinds power XFRs?
On Friday, December 4, 2020 at 12:32:44 PM UTC-5, wrote:
I have a McIntosh MX110Z with a bad transformer. Any recommendations for rewinding? I've never done one and have no interest in trying. Thanks. https://www.mercurymagnetics.com/bra...ation-service/ And there is the Mother Ship, McIntosh itself. Peter Wieck Melrose Park, PA |
#3
Posted to sci.electronics.repair
|
|||
|
|||
Who rewinds power XFRs?
On Friday, December 4, 2020 at 1:09:55 PM UTC-5, Peter W. wrote:
On Friday, December 4, 2020 at 12:32:44 PM UTC-5, wrote: I have a McIntosh MX110Z with a bad transformer. Any recommendations for rewinding? I've never done one and have no interest in trying. Thanks. https://www.mercurymagnetics.com/bra...ation-service/ And there is the Mother Ship, McIntosh itself. Peter Wieck Melrose Park, PA I did take the long shot and emailed McIntosh directly. I haven't heard back from them yet, but I assume given the age of this tuner/pre, they won't be of much help. |
#4
Posted to sci.electronics.repair
|
|||
|
|||
Who rewinds power XFRs?
On 12/4/2020 9:32 AM, wrote:
I have a McIntosh MX110Z with a bad transformer. Any recommendations for rewinding? I've never done one and have no interest in trying. Thanks. You can do better that that post. How is it bad? Shorted turn, open turn, short to core? Which winding? Primary or secondary? What told you the transformer is bad? Likely there is a transformer available with similar ratings that will replace the transformer. Paul |
#5
Posted to sci.electronics.repair
|
|||
|
|||
Who rewinds power XFRs?
On Saturday, December 5, 2020 at 1:09:39 PM UTC-5, Paul Drahn wrote:
On 12/4/2020 9:32 AM, wrote: I have a McIntosh MX110Z with a bad transformer. Any recommendations for rewinding? I've never done one and have no interest in trying. Thanks. You can do better that that post. How is it bad? Shorted turn, open turn, short to core? Which winding? Primary or secondary? What told you the transformer is bad? Likely there is a transformer available with similar ratings that will replace the transformer. Paul It *looks* bad... |
#6
Posted to sci.electronics.repair
|
|||
|
|||
Who rewinds power XFRs?
Paul Drahn wrote:
============== I have a McIntosh MX110Z with a bad transformer. You can do better that that post. How is it bad? Shorted turn, open turn, short to core? Which winding? Primary or secondary? What told you the transformer is bad? Likely there is a transformer available with similar ratings that will replace the transformer. ** For sure - sitting inside another MX110Z that is non working. ..... Phil l |
#7
Posted to sci.electronics.repair
|
|||
|
|||
Who rewinds power XFRs?
A few things:
a) McIntosh winds their own transformers. b) McIntosh has been in business for many years, and through many ups and downs. c) Meaning that their management at least has some basic business intelligence. d) Suggesting that the transformers they make/made are not unique to each individual component. e) Suggesting that it is quite likely that they may have that transformer available. Peter Wieck Melrose Park, PA |
#8
Posted to sci.electronics.repair
|
|||
|
|||
Who rewinds power XFRs?
On Sunday, December 6, 2020 at 7:49:16 AM UTC-5, Peter W. wrote:
A few things: a) McIntosh winds their own transformers. b) McIntosh has been in business for many years, and through many ups and downs. c) Meaning that their management at least has some basic business intelligence. d) Suggesting that the transformers they make/made are not unique to each individual component. e) Suggesting that it is quite likely that they may have that transformer available. It's not. I emailed McIntosh asking about a replacement, or a suggested "universal" replacement that might physically fit the tight chassis that could be installed with some circuit modification, or perhaps a suggestion of a rewinder they were familiar with or might even have used. I received a very quick and terse (if not polite) email from McIntosh Friday that answered all three of my questions with a simple "Im sorry there are no options for this transformer." Boom. The MX110Z is very very tight. There's literally no room for a transformer that would allow the case to fit if the replacement was any bigger even by a small percentage. This particular piece is known to have a power transformer that runs *very* hot even when everything is otherwise normal. The transformer has a B+ winding and three filament windings and is also supposed to be more heavily shielded than the average bear. I could probably find a way of cobbling a different power transformer and another smaller filament transformer somewhere else on the chassis (or just build a remote XFR box with an umbilical) but I don't want to reinvent the wheel at this point, plus I feel most of the *value* of this piece is in the originality of it, not to mention Mc's careful design of the filament circuit and wire routing for hum mitigation. Add to that the fact that two of the four selenium rectifiers under the deck relieved themselves of tiny solder balls (which happens when the 1A slow blow is replaced with a 20A fuse), and all cans are original and probably need to be restuffed, and it just seems like a project not worth the time at this point. I returned the tuner/pre to the owner yesterday with the suggestion of either putting it on ebay, where this model in non working condition will bring $400 at least, or keep checking ebay and finding one in poor cosmetic condition with a good XFR in it. |
#9
Posted to sci.electronics.repair
|
|||
|
|||
Who rewinds power XFRs?
I returned the tuner/pre to the owner yesterday with the suggestion of either putting it on ebay, where this model in non working condition will bring $400 at least, or keep checking ebay and finding one in poor cosmetic condition with a good XFR in it.
Or send it out to be rewound. |
#11
Posted to sci.electronics.repair
|
|||
|
|||
Who rewinds power XFRs?
On Friday, December 4, 2020 at 12:32:44 PM UTC-5, wrote:
I have a McIntosh MX110Z with a bad transformer. Any recommendations for rewinding? I've never done one and have no interest in trying. Thanks. Follow up for general information. I received a second email from McIntosh a couple of days ago that said the only person they had to rewind transformers recently passed away. While looking for a rewinder on the web, I had seen references to a rewinder many used but who was in poor health, so maybe McIntosh used the same guy. |
#12
Posted to sci.electronics.repair
|
|||
|
|||
Who rewinds power XFRs?
On Sunday, December 6, 2020 at 7:49:16 AM UTC-5, Peter W. wrote:
A few things: a) McIntosh winds their own transformers. b) McIntosh has been in business for many years, and through many ups and downs. c) Meaning that their management at least has some basic business intelligence. That means nothing. Management team assistants can be good or bad irrespective of time. The smaller; more prejudiced; more nepotistic and less meritocratic, the worse off. Like with the Trump family. d) Suggesting that the transformers they make/made are not unique to each individual component. e) Suggesting that it is quite likely that they may have that transformer available. Peter Wieck Melrose Park, PA |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
[Power] UK breaks solar power record, supplies more power than nuke | UK diy | |||
Magnavox VCR (model VR9640AT01) rewinds 4 seconds then shuts off | Electronics Repair | |||
Magnavox VR9640AT01 VCR rewinds 4 seconds then shuts off. No buttons work | Electronics Repair | |||
X-Box power surge - blew out switching power supply | Electronics Repair | |||
JVC NV-55BX4 will not power up with convergence power plugged in. | Electronics Repair |