Electronics Repair (sci.electronics.repair) Discussion of repairing electronic equipment. Topics include requests for assistance, where to obtain servicing information and parts, techniques for diagnosis and repair, and annecdotes about success, failures and problems.

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
  #1   Report Post  
Jerry G.
 
Posts: n/a
Default Replacing electrolytics

You should use the ones that are rated for 105 deg Cels. Use any good
quality cap, as long as the specs are proper. Just make sure that the
voltage rating is the same or higher than the original. A higher voltage
rated cap will most likely last longer, as long as the heat and stress to
the cap is within its tolerance. It is heat that destroys the caps more than
anything else.

--

Jerry G.
=====


"mo" wrote in message
om...
All TV techs know that a common fault in many tv power supplies is due
to faulty electrolytics.
It is usually the cap that provides the drive to the chopper.
I have access to various types including low leakage and low
impedance.
Should I be using the original or replace with one that is more
reliable.
Which capacitor is most suitable in this circuit and hot environment.
Many tv's from the olden days,never had their rear cover removed for
the first time until 8 years or so elapsed.


  #2   Report Post  
Jim Yanik
 
Posts: n/a
Default Replacing electrolytics

"Jerry G." wrote in
:

You should use the ones that are rated for 105 deg Cels. Use any good
quality cap, as long as the specs are proper. Just make sure that the
voltage rating is the same or higher than the original. A higher
voltage rated cap will most likely last longer, as long as the heat
and stress to the cap is within its tolerance. It is heat that
destroys the caps more than anything else.


I beg to differ.
In switchers you not only want 105deg caps,you want LOW-ESR caps.IMO,the
low ESR is more important.That's where the stress comes from.

--
Jim Yanik
jyanik-at-kua.net
  #3   Report Post  
CJT
 
Posts: n/a
Default Replacing electrolytics

Jim Yanik wrote:

"Jerry G." wrote in
:


You should use the ones that are rated for 105 deg Cels. Use any good
quality cap, as long as the specs are proper. Just make sure that the
voltage rating is the same or higher than the original. A higher
voltage rated cap will most likely last longer, as long as the heat
and stress to the cap is within its tolerance. It is heat that
destroys the caps more than anything else.



I beg to differ.
In switchers you not only want 105deg caps,you want LOW-ESR caps.IMO,the
low ESR is more important.That's where the stress comes from.


I don't see ESR specified on catalog pages for capacitors (e.g. at
Digikey), so what should I be looking for in the specifications, and
what is a good value, in your opinion?

--
The e-mail address in our reply-to line is reversed in an attempt to
minimize spam. Our true address is of the form .
  #4   Report Post  
CJT
 
Posts: n/a
Default Replacing electrolytics

Ross Herbert wrote:

On Wed, 16 Jun 2004 02:51:34 GMT, CJT wrote:

|Jim Yanik wrote:
|
| "Jerry G." wrote in
| :
|
|
|You should use the ones that are rated for 105 deg Cels. Use any good
|quality cap, as long as the specs are proper. Just make sure that the
|voltage rating is the same or higher than the original. A higher
|voltage rated cap will most likely last longer, as long as the heat
|and stress to the cap is within its tolerance. It is heat that
|destroys the caps more than anything else.
|
|
|
| I beg to differ.
| In switchers you not only want 105deg caps,you want LOW-ESR caps.IMO,the
| low ESR is more important.That's where the stress comes from.
|
|
|I don't see ESR specified on catalog pages for capacitors (e.g. at
|Digikey), so what should I be looking for in the specifications, and
|what is a good value, in your opinion?


No, but they often state "low impedance" and "long life" along with
the temperature rating and often quote impedance values. For instance
look at this page http://dkc3.digikey.com/PDF/T042/SectE.pdf


Well, that URL points to a pdf that's 145 pages long, so I'm still a
little unclear just what you're looking at.


You will see that they have a column actually showing the impedance at
100KHz as well as the rated ripple current. These factors are vital
for a person wishing to select a capacitor for a specific function.
Looking at this Panasonic type I can guess that it would be ideal for
the intended application of the OP. There are undoubtedly even higher
spec devices in the Digikey catalog but I'll leave that to the OP to
chase up.



--
The e-mail address in our reply-to line is reversed in an attempt to
minimize spam. Our true address is of the form .
  #5   Report Post  
CJT
 
Posts: n/a
Default Replacing electrolytics

CJT wrote:

Ross Herbert wrote:

On Wed, 16 Jun 2004 02:51:34 GMT, CJT wrote:

|Jim Yanik wrote:
|
| "Jerry G." wrote in
| : | | |You should use the
ones that are rated for 105 deg Cels. Use any good
|quality cap, as long as the specs are proper. Just make sure that the
|voltage rating is the same or higher than the original. A higher
|voltage rated cap will most likely last longer, as long as the heat
|and stress to the cap is within its tolerance. It is heat that
|destroys the caps more than anything else.
|
| | | I beg to differ.
| In switchers you not only want 105deg caps,you want LOW-ESR
caps.IMO,the | low ESR is more important.That's where the stress
comes from.
| |
|I don't see ESR specified on catalog pages for capacitors (e.g. at
|Digikey), so what should I be looking for in the specifications, and
|what is a good value, in your opinion?


No, but they often state "low impedance" and "long life" along with
the temperature rating and often quote impedance values. For instance
look at this page http://dkc3.digikey.com/PDF/T042/SectE.pdf



Well, that URL points to a pdf that's 145 pages long, so I'm still a
little unclear just what you're looking at.


OK, I've done some Googling and reading since I posted that, so I now
understand better the significance of tan delta. However, it seems to
me, looking at the Digikey catalog, that the available 105 degree
capacitors are fairly competitive in that spec, so I'm not sure it's
really all that useful as a selection criterion.

I'd appreciate your insights.



You will see that they have a column actually showing the impedance at
100KHz as well as the rated ripple current. These factors are vital
for a person wishing to select a capacitor for a specific function.
Looking at this Panasonic type I can guess that it would be ideal for
the intended application of the OP. There are undoubtedly even higher
spec devices in the Digikey catalog but I'll leave that to the OP to
chase up.






--
The e-mail address in our reply-to line is reversed in an attempt to
minimize spam. Our true address is of the form .
Reply
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules

Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Replacing taps. Mary Pegg UK diy 7 July 3rd 04 02:42 PM
Replacing hot water cylinder. Kevin UK diy 14 June 10th 04 06:26 PM
Near death boiler + replacing a boiler David Hearn UK diy 9 January 26th 04 01:44 PM
replacing a banister? Harris UK diy 3 August 22nd 03 09:46 AM


All times are GMT +1. The time now is 04:06 PM.

Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 DIYbanter.
The comments are property of their posters.
 

About Us

"It's about DIY & home improvement"