Pioneer PD-M600 changer. Presents disc but does not spin up then the
same thing happens with each disc.
Anyone any clues or where to get service manual, preferably free.

F Murtz writes:

Pioneer PD-M600 changer. Presents disc but does not spin up then the
same thing happens with each disc.
Anyone any clues or where to get service manual, preferably free.

Bad flex cable, dropped lens, dirty spindle motor, decayed rubber grommets,
etc.

--
sam | Sci.Electronics.Repair FAQ: http://www.repairfaq.org/
Repair | Main Table of Contents: http://www.repairfaq.org/REPAIR/
+Lasers | Sam's Laser FAQ: http://www.repairfaq.org/sam/lasersam.htm
| Mirror Sites: http://www.repairfaq.org/REPAIR/F_mirror.html

Important: Anything sent to the email address in the message header above is
ignored unless my full name AND either lasers or electronics is included in the
subject line. Or, you can contact me via the Feedback Form in the FAQs.

Samuel M. Goldwasser wrote:
F writes:

Pioneer PD-M600 changer. Presents disc but does not spin up then the
same thing happens with each disc.
Anyone any clues or where to get service manual, preferably free.

Bad flex cable, dropped lens, dirty spindle motor, decayed rubber grommets,
etc.

Motor does not attempt to start spinning,Have not checked for voltage at
spindle motor yet, just had quick look so far.
Would feel happier with schematic but the only ones I can find want
money and I am a bit wary of paying for a pig in a poke.

"F Murtz" wrote in message
...
Samuel M. Goldwasser wrote:
F writes:

Pioneer PD-M600 changer. Presents disc but does not spin up then the
same thing happens with each disc.
Anyone any clues or where to get service manual, preferably free.

Bad flex cable, dropped lens, dirty spindle motor, decayed rubber
grommets,
etc.

Motor does not attempt to start spinning,Have not checked for voltage at
spindle motor yet, just had quick look so far.
Would feel happier with schematic but the only ones I can find want money
and I am a bit wary of paying for a pig in a poke.

All that Sam said seconded. Have you checked that the lens is still in place
? Very common for it to come out and be rolling round in the bottom of the
player somewhere ...

Arfa

"Arfa Daily" writes:

"F Murtz" wrote in message
...
Samuel M. Goldwasser wrote:
F writes:

Pioneer PD-M600 changer. Presents disc but does not spin up then the
same thing happens with each disc.
Anyone any clues or where to get service manual, preferably free.

Bad flex cable, dropped lens, dirty spindle motor, decayed rubber
grommets,
etc.

Motor does not attempt to start spinning,Have not checked for
voltage at spindle motor yet, just had quick look so far.
Would feel happier with schematic but the only ones I can find want
money and I am a bit wary of paying for a pig in a poke.

All that Sam said seconded. Have you checked that the lens is still in
place ? Very common for it to come out and be rolling round in the
bottom of the player somewhere ...

And despite the incredible precision involved in the optical pickup,
gently pushing the lens back in place and securing it with a couple
drops of 5 minute Epoxy often works! DON'T use Superglue!

--
sam | Sci.Electronics.Repair FAQ: http://www.repairfaq.org/
Repair | Main Table of Contents: http://www.repairfaq.org/REPAIR/
+Lasers | Sam's Laser FAQ: http://www.repairfaq.org/sam/lasersam.htm
| Mirror Sites: http://www.repairfaq.org/REPAIR/F_mirror.html

Important: Anything sent to the email address in the message header above is
ignored unless my full name AND either lasers or electronics is included in the
subject line. Or, you can contact me via the Feedback Form in the FAQs.

Samuel M. Goldwasser wrote:
"Arfa writes:

"F wrote in message
...
Samuel M. Goldwasser wrote:
F writes:

Pioneer PD-M600 changer. Presents disc but does not spin up then the
same thing happens with each disc.
Anyone any clues or where to get service manual, preferably free.

Bad flex cable, dropped lens, dirty spindle motor, decayed rubber
grommets,
etc.

Motor does not attempt to start spinning,Have not checked for
voltage at spindle motor yet, just had quick look so far.
Would feel happier with schematic but the only ones I can find want
money and I am a bit wary of paying for a pig in a poke.

All that Sam said seconded. Have you checked that the lens is still in
place ? Very common for it to come out and be rolling round in the
bottom of the player somewhere ...

And despite the incredible precision involved in the optical pickup,
gently pushing the lens back in place and securing it with a couple
drops of 5 minute Epoxy often works! DON'T use Superglue!



It seems the lense is missing,Aparently the owner (friend of a friend)
moved house and then it stopped working,probably shook it loose.I think
it has fallen through the bottom of the case.
Would you still be able to get spares?