| Page 1 of 2 | 1 | 2 |
|
|
Nuisance fastners - winge
I had occasion to dismantle a cheap pedestal fan the other day (Coles
Home Collection). It hadn't failed, but I wanted to see how it was wired up (that's another story). The cover to the button panel was held in place by four screws which were identical except that two were philips head type, and the other two had a triangular socket in the head. I have bits to cope with most things I've encountered, but not those. What's the point? Are they worried about competition for repairing these $10 fans? Do consumers regularly electrocute themselves by taking fans apart without knowing what they're doing? Sylvia. |
Nuisance fastners - winge
On Wed, 09 Feb 2011 22:29:35 +1100, Sylvia Else
wrote: I had occasion to dismantle a cheap pedestal fan the other day (Coles Home Collection). It hadn't failed, but I wanted to see how it was wired up (that's another story). The cover to the button panel was held in place by four screws which were identical except that two were philips head type, and the other two had a triangular socket in the head. I have bits to cope with most things I've encountered, but not those. What's the point? Are they worried about competition for repairing these $10 fans? Do consumers regularly electrocute themselves by taking fans apart without knowing what they're doing? Sylvia. I just used a small flat blade screwdriver to remove them. Got to be the right size though to jam along one flat of the triangle. -- Sell your surplus electronic components at http://ozcomponents.com Search or browse for that IC, capacitor, crystal or other component you need. Or find new components at http://auscomponents.com |
Nuisance fastners - winge
On 9/02/2011 11:23 PM, Alan wrote:
On Wed, 09 Feb 2011 22:29:35 +1100, Sylvia Else wrote: I had occasion to dismantle a cheap pedestal fan the other day (Coles Home Collection). It hadn't failed, but I wanted to see how it was wired up (that's another story). The cover to the button panel was held in place by four screws which were identical except that two were philips head type, and the other two had a triangular socket in the head. I have bits to cope with most things I've encountered, but not those. What's the point? Are they worried about competition for repairing these $10 fans? Do consumers regularly electrocute themselves by taking fans apart without knowing what they're doing? Sylvia. I just used a small flat blade screwdriver to remove them. Got to be the right size though to jam along one flat of the triangle. Well, I got one of them undone using a tri-wing bit, but stripped the other attempting to do the same thing. However, I managed to see what I wanted to see. http://upload.wikimedia.org/wikipedia/commons/thumb/e/e9/Screw_Head_-_Tri-wing.svg/40px-Screw_Head_-_Tri-wing.svg.png Sylvia. -- Sell your surplus electronic components at http://ozcomponents.com Search or browse for that IC, capacitor, crystal or other component you need. Or find new components at http://auscomponents.com |
Nuisance fastners - winge
"Sylvia Else" wrote in message ... On 9/02/2011 11:23 PM, Alan wrote: On Wed, 09 Feb 2011 22:29:35 +1100, Sylvia Else wrote: I had occasion to dismantle a cheap pedestal fan the other day (Coles Home Collection). It hadn't failed, but I wanted to see how it was wired up (that's another story). The cover to the button panel was held in place by four screws which were identical except that two were philips head type, and the other two had a triangular socket in the head. I have bits to cope with most things I've encountered, but not those. What's the point? Are they worried about competition for repairing these $10 fans? Do consumers regularly electrocute themselves by taking fans apart without knowing what they're doing? Sylvia. I just used a small flat blade screwdriver to remove them. Got to be the right size though to jam along one flat of the triangle. Well, I got one of them undone using a tri-wing bit, but stripped the other attempting to do the same thing. However, I managed to see what I wanted to see. Which was ? Is there a point to this thread apart from the type of screw you couldn't screw ? |
Nuisance fastners - winge
On Feb 9, 10:35*pm, Sylvia Else wrote:
On 9/02/2011 11:23 PM, Alan wrote: On Wed, 09 Feb 2011 22:29:35 +1100, Sylvia Else *wrote: I had occasion to dismantle a cheap pedestal fan the other day (Coles Home Collection). It hadn't failed, but I wanted to see how it was wired up (that's another story). The cover to the button panel was held in place by four screws which were identical except that two were philips head type, and the other two had a triangular socket in the head. I have bits to cope with most things I've encountered, but not those. What's the point? Are they worried about competition for repairing these $10 fans? Do consumers regularly electrocute themselves by taking fans apart without knowing what they're doing? Sylvia. I just used a small flat blade screwdriver to remove them. Got to be the right size though to jam along one flat of the triangle. Well, I got one of them undone using a tri-wing bit, but stripped the other attempting to do the same thing. However, I managed to see what I wanted to see. http://upload.wikimedia.org/wikipedia/commons/thumb/e/e9/Screw_Head_-... Sylvia. -- Sell your surplus electronic components at http://ozcomponents.com Search or browse for that IC, capacitor, crystal or other component you need. Or find new components athttp://auscomponents.com And how was it wired up ? |
Nuisance fastners - winge
On 2/9/2011 5:29 AM, Sylvia Else wrote:
Do consumers regularly electrocute themselves by taking fans apart without knowing what they're doing? I'm reminded of an old Rodriguez cartoon in Popular Electronics. First panel: On a large speaker cabinet. "to prevent shock do not remove cover" Second panel: Owner taking out a LOT of screws. Third panel: Owner on floor clutching chest. Inside of huge cabinet has 2" transistor radio speaker inside. Jeff |
Nuisance fastners - winge
atec77 wrote: On 10/02/2011 2:05 AM, fritz wrote: Which was ? Is there a point to this thread apart from the type of screw you couldn't screw ? The point is stupid is as stupid does (syliva) the screws are the manufactures way of saying no user serviceable parts do not open It is their lawyer's way of attempting to avoid lawsuits. -- You can't fix stupid. You can't even put a band-aid on it, because it's Teflon coated. |
Nuisance fastners - winge
"Sylvia Else" wrote in message ... I had occasion to dismantle a cheap pedestal fan the other day (Coles Home Collection). It hadn't failed, but I wanted to see how it was wired up (that's another story). The cover to the button panel was held in place by four screws which were identical except that two were philips head type, and the other two had a triangular socket in the head. I have bits to cope with most things I've encountered, but not those. What's the point? Are they worried about competition for repairing these $10 fans? Do consumers regularly electrocute themselves by taking fans apart without knowing what they're doing? Sylvia. They are only a tamperproof head of which there are various and easily available.. Wait until you come across a coffin head screw.I believe the reason for using them is that some countries prevent the dismantle of an appliance without the use of a tool or special tool so this way all fields are covered in one assembly. Did you find out how it worked. They are made to break. Best way to keep them longer is to keep the Blades clean and lubricate the bearings NOT with WD40 or the like. Metro |
Nuisance fastners - winge
On 10/02/2011 10:08 AM, kreed wrote:
On Feb 9, 10:35 pm, Sylvia wrote: On 9/02/2011 11:23 PM, Alan wrote: On Wed, 09 Feb 2011 22:29:35 +1100, Sylvia Else wrote: I had occasion to dismantle a cheap pedestal fan the other day (Coles Home Collection). It hadn't failed, but I wanted to see how it was wired up (that's another story). The cover to the button panel was held in place by four screws which were identical except that two were philips head type, and the other two had a triangular socket in the head. I have bits to cope with most things I've encountered, but not those. What's the point? Are they worried about competition for repairing these $10 fans? Do consumers regularly electrocute themselves by taking fans apart without knowing what they're doing? Sylvia. I just used a small flat blade screwdriver to remove them. Got to be the right size though to jam along one flat of the triangle. Well, I got one of them undone using a tri-wing bit, but stripped the other attempting to do the same thing. However, I managed to see what I wanted to see. http://upload.wikimedia.org/wikipedia/commons/thumb/e/e9/Screw_Head_-... Sylvia. -- Sell your surplus electronic components at http://ozcomponents.com Search or browse for that IC, capacitor, crystal or other component you need. Or find new components athttp://auscomponents.com And how was it wired up ? In a particular way. Sylvia. |
Nuisance fastners - winge
On 10/02/2011 11:23 AM, Metro wrote:
"Sylvia wrote in message ... I had occasion to dismantle a cheap pedestal fan the other day (Coles Home Collection). It hadn't failed, but I wanted to see how it was wired up (that's another story). The cover to the button panel was held in place by four screws which were identical except that two were philips head type, and the other two had a triangular socket in the head. I have bits to cope with most things I've encountered, but not those. What's the point? Are they worried about competition for repairing these $10 fans? Do consumers regularly electrocute themselves by taking fans apart without knowing what they're doing? Sylvia. They are only a tamperproof head of which there are various and easily available.. Wait until you come across a coffin head screw.I believe the reason for using them is that some countries prevent the dismantle of an appliance without the use of a tool or special tool so this way all fields are covered in one assembly. Did you find out how it worked. They are made to break. Best way to keep them longer is to keep the Blades clean and lubricate the bearings NOT with WD40 or the like. As I said, it hadn't broken. I was actually trying to figure out which wire was which leading to the induction motor. I had in mind making it run backwards. Aerofoils don't perform as well backwards, but they do perform. However, on further consideration I realised that the fan blades would be aerodynamically stalled if the fan ran backwards, with the result that it would probably not work much at all. Sylvia. |
Nuisance fastners - winge
On 10/02/2011 3:05 AM, fritz wrote:
Which was ? Is there a point to this thread apart from the type of screw you couldn't screw ? Not really. The word "winge" in the subject line should have hinted at that. Sylvia. |
Nuisance fastners - winge
"Michael A. Terrell" wrote in message m... atec77 wrote: On 10/02/2011 2:05 AM, fritz wrote: Which was ? Is there a point to this thread apart from the type of screw you couldn't screw ? The point is stupid is as stupid does (syliva) the screws are the manufactures way of saying no user serviceable parts do not open It is their lawyer's way of attempting to avoid lawsuits. Did it work? |
Nuisance fastners - winge
"Sylvia Else" wrote in message ... On 10/02/2011 11:23 AM, Metro wrote: "Sylvia wrote in message ... I had occasion to dismantle a cheap pedestal fan the other day (Coles Home Collection). It hadn't failed, but I wanted to see how it was wired up (that's another story). The cover to the button panel was held in place by four screws which were identical except that two were philips head type, and the other two had a triangular socket in the head. I have bits to cope with most things I've encountered, but not those. What's the point? Are they worried about competition for repairing these $10 fans? Do consumers regularly electrocute themselves by taking fans apart without knowing what they're doing? Sylvia. They are only a tamperproof head of which there are various and easily available.. Wait until you come across a coffin head screw.I believe the reason for using them is that some countries prevent the dismantle of an appliance without the use of a tool or special tool so this way all fields are covered in one assembly. Did you find out how it worked. They are made to break. Best way to keep them longer is to keep the Blades clean and lubricate the bearings NOT with WD40 or the like. As I said, it hadn't broken. I was actually trying to figure out which wire was which leading to the induction motor. I had in mind making it run backwards. Aerofoils don't perform as well backwards, but they do perform. However, on further consideration I realised that the fan blades would be aerodynamically stalled if the fan ran backwards, with the result that it would probably not work much at all. If the fan is symetrical - snap off pairs of opposing blades. Doesn't matter if there's only 6 to start with - some helicopters have "scissor" tail rotors. |
Nuisance fastners - winge
ian field wrote: "Michael A. Terrell" ? wrote in message m... ? ? atec77 wrote: ?? ?? On 10/02/2011 2:05 AM, fritz wrote: ?? ? ?? ? ?? ? Which was ? ?? ? Is there a point to this thread apart from the type of screw you ?? ? couldn't screw ? ?? ? ?? The point is stupid is as stupid does (syliva) ?? the screws are the manufactures way of saying no user serviceable ?? parts do not open ? ? ? It is their lawyer's way of attempting to avoid lawsuits. Did it work? Did you sue them? -- You can't fix stupid. You can't even put a band-aid on it, because it's Teflon coated. |
Nuisance fastners - winge
On 11/02/2011 8:11 AM, ian field wrote:
"Sylvia wrote in message ... On 10/02/2011 11:23 AM, Metro wrote: "Sylvia wrote in message ... I had occasion to dismantle a cheap pedestal fan the other day (Coles Home Collection). It hadn't failed, but I wanted to see how it was wired up (that's another story). The cover to the button panel was held in place by four screws which were identical except that two were philips head type, and the other two had a triangular socket in the head. I have bits to cope with most things I've encountered, but not those. What's the point? Are they worried about competition for repairing these $10 fans? Do consumers regularly electrocute themselves by taking fans apart without knowing what they're doing? Sylvia. They are only a tamperproof head of which there are various and easily available.. Wait until you come across a coffin head screw.I believe the reason for using them is that some countries prevent the dismantle of an appliance without the use of a tool or special tool so this way all fields are covered in one assembly. Did you find out how it worked. They are made to break. Best way to keep them longer is to keep the Blades clean and lubricate the bearings NOT with WD40 or the like. As I said, it hadn't broken. I was actually trying to figure out which wire was which leading to the induction motor. I had in mind making it run backwards. Aerofoils don't perform as well backwards, but they do perform. However, on further consideration I realised that the fan blades would be aerodynamically stalled if the fan ran backwards, with the result that it would probably not work much at all. If the fan is symetrical - snap off pairs of opposing blades. That's not going to fix the problem of the blades being stalled. What I would really need to do is fit the one-piece fan blade assembly on back to front (as well as reversing the motor), but the fan blade assembly is not designed to be attached the other way around. Sylvia. |
Nuisance fastners - winge
Sylvia Else wrote:
What I would really need to do is fit the one-piece fan blade assembly on back to front (as well as reversing the motor), but the fan blade assembly is not designed to be attached the other way around. If it is a shaded-pole induction motor, it will not be possible to run it in reveres unless you dismantle the whole assembly and put the stator in the other way around. It would be more effective to get a spare fan boss and make new blades for it. (I have made a shaded-pole gramophone motor run backwards, but I had to completely rebuild it and add extra windings to make it work.) -- ~ Adrian Tuddenham ~ (Remove the ".invalid"s and add ".co.uk" to reply) www.poppyrecords.co.uk |
Nuisance fastners - winge
On Feb 11, 9:20*pm, Sylvia Else wrote:
On 11/02/2011 8:11 AM, ian field wrote: "Sylvia *wrote in message ... On 10/02/2011 11:23 AM, Metro wrote: "Sylvia * wrote in message ... I had occasion to dismantle a cheap pedestal fan the other day (Coles Home Collection). It hadn't failed, but I wanted to see how it was wired up (that's another story). The cover to the button panel was held in place by four screws which were identical except that two were philips head type, and the other two had a triangular socket in the head. I have bits to cope with most things I've encountered, but not those.. What's the point? Are they worried about competition for repairing these $10 fans? Do consumers regularly electrocute themselves by taking fans apart without knowing what they're doing? Sylvia. They are only a tamperproof head of which there are various and easily available.. Wait until you come across a coffin head screw.I believe the reason for using them is that some countries prevent the dismantle of an appliance without the use of a tool or special tool so this way all fields are covered in one assembly. Did you find out how it worked. They are made to break. Best way to keep them longer is to keep the Blades clean and lubricate the bearings NOT with WD40 or the like. As I said, it hadn't broken. I was actually trying to figure out which wire was which leading to the induction motor. I had in mind making it run backwards. Aerofoils don't perform as well backwards, but they do perform. However, on further consideration I realised that the fan blades would be aerodynamically stalled if the fan ran backwards, with the result that it would probably not work much at all. If the fan is symetrical - snap off pairs of opposing blades. That's not going to fix the problem of the blades being stalled. What I would really need to do is fit the one-piece fan blade assembly on back to front (as well as reversing the motor), but the fan blade assembly is not designed to be attached the other way around. Sylvia. Might sound silly, but cant the entire fan head (including motor) be rotated 180 degrees, or do you want the air intake without the motor in the way ? |
Nuisance fastners - winge
On 11/02/2011 11:37 PM, Adrian Tuddenham wrote:
Sylvia wrote: What I would really need to do is fit the one-piece fan blade assembly on back to front (as well as reversing the motor), but the fan blade assembly is not designed to be attached the other way around. If it is a shaded-pole induction motor, it will not be possible to run it in reveres unless you dismantle the whole assembly and put the stator in the other way around. It would be more effective to get a spare fan boss and make new blades for it. It's not shaded pole. It has two sets of windings perpendicular to each other, and a capacitor which I believe is in series with one set of windings. Sylvia. |
Nuisance fastners - winge
On 11/02/2011 11:56 PM, kreed wrote:
On Feb 11, 9:20 pm, Sylvia wrote: On 11/02/2011 8:11 AM, ian field wrote: "Sylvia wrote in message ... On 10/02/2011 11:23 AM, Metro wrote: "Sylvia wrote in message ... I had occasion to dismantle a cheap pedestal fan the other day (Coles Home Collection). It hadn't failed, but I wanted to see how it was wired up (that's another story). The cover to the button panel was held in place by four screws which were identical except that two were philips head type, and the other two had a triangular socket in the head. I have bits to cope with most things I've encountered, but not those. What's the point? Are they worried about competition for repairing these $10 fans? Do consumers regularly electrocute themselves by taking fans apart without knowing what they're doing? Sylvia. They are only a tamperproof head of which there are various and easily available.. Wait until you come across a coffin head screw.I believe the reason for using them is that some countries prevent the dismantle of an appliance without the use of a tool or special tool so this way all fields are covered in one assembly. Did you find out how it worked. They are made to break. Best way to keep them longer is to keep the Blades clean and lubricate the bearings NOT with WD40 or the like. As I said, it hadn't broken. I was actually trying to figure out which wire was which leading to the induction motor. I had in mind making it run backwards. Aerofoils don't perform as well backwards, but they do perform. However, on further consideration I realised that the fan blades would be aerodynamically stalled if the fan ran backwards, with the result that it would probably not work much at all. If the fan is symetrical - snap off pairs of opposing blades. That's not going to fix the problem of the blades being stalled. What I would really need to do is fit the one-piece fan blade assembly on back to front (as well as reversing the motor), but the fan blade assembly is not designed to be attached the other way around. Sylvia. Might sound silly, but cant the entire fan head (including motor) be rotated 180 degrees, or do you want the air intake without the motor in the way ? The application is to suck cool air in through an open window at night. During the recent heat wave, it was noticeable that even though the temperature outside drops at night, the temperature of the house doesn't drop that much. The problem is lack of air flow. A conventional pedestal fan blows in such a direction that when it's placed as near as possible to a window, the fan blades are still quite a way from the cool air, and so the result is not as effective as it might be. If I could reverse the direction of flow, then I could also turn then fan around, so that the blades would be much closer to the window. I considered simply building a duct, but the cost of materials was excessive. I'm thinking of using box fans instead. Sylvia. |
Nuisance fastners - winge
Sylvia Else wrote:
On 11/02/2011 11:37 PM, Adrian Tuddenham wrote: Sylvia wrote: What I would really need to do is fit the one-piece fan blade assembly on back to front (as well as reversing the motor), but the fan blade assembly is not designed to be attached the other way around. If it is a shaded-pole induction motor, it will not be possible to run it in reveres unless you dismantle the whole assembly and put the stator in the other way around. It would be more effective to get a spare fan boss and make new blades for it. It's not shaded pole. It has two sets of windings perpendicular to each other, and a capacitor which I believe is in series with one set of windings. In that case it ought to be reversible - but I would still consider making a replacement fan if you want a reasonably efficient reversed airflow.. -- ~ Adrian Tuddenham ~ (Remove the ".invalid"s and add ".co.uk" to reply) www.poppyrecords.co.uk |
Nuisance fastners - winge
Sylvia Else wrote:
On 11/02/2011 11:56 PM, kreed wrote: On Feb 11, 9:20 pm, Sylvia wrote: On 11/02/2011 8:11 AM, ian field wrote: "Sylvia wrote in message ... On 10/02/2011 11:23 AM, Metro wrote: "Sylvia wrote in message ... I had occasion to dismantle a cheap pedestal fan the other day (Coles Home Collection). It hadn't failed, but I wanted to see how it was wired up (that's another story). The cover to the button panel was held in place by four screws which were identical except that two were philips head type, and the other two had a triangular socket in the head. I have bits to cope with most things I've encountered, but not those. What's the point? Are they worried about competition for repairing these $10 fans? Do consumers regularly electrocute themselves by taking fans apart without knowing what they're doing? Sylvia. They are only a tamperproof head of which there are various and easily available.. Wait until you come across a coffin head screw.I believe the reason for using them is that some countries prevent the dismantle of an appliance without the use of a tool or special tool so this way all fields are covered in one assembly. Did you find out how it worked. They are made to break. Best way to keep them longer is to keep the Blades clean and lubricate the bearings NOT with WD40 or the like. As I said, it hadn't broken. I was actually trying to figure out which wire was which leading to the induction motor. I had in mind making it run backwards. Aerofoils don't perform as well backwards, but they do perform. However, on further consideration I realised that the fan blades would be aerodynamically stalled if the fan ran backwards, with the result that it would probably not work much at all. If the fan is symetrical - snap off pairs of opposing blades. That's not going to fix the problem of the blades being stalled. What I would really need to do is fit the one-piece fan blade assembly on back to front (as well as reversing the motor), but the fan blade assembly is not designed to be attached the other way around. Sylvia. Might sound silly, but cant the entire fan head (including motor) be rotated 180 degrees, or do you want the air intake without the motor in the way ? The application is to suck cool air in through an open window at night. During the recent heat wave, it was noticeable that even though the temperature outside drops at night, the temperature of the house doesn't drop that much. The problem is lack of air flow. A conventional pedestal fan blows in such a direction that when it's placed as near as possible to a window, the fan blades are still quite a way from the cool air, and so the result is not as effective as it might be. If I could reverse the direction of flow, then I could also turn then fan around, so that the blades would be much closer to the window. I considered simply building a duct, but the cost of materials was excessive. I'm thinking of using box fans instead. Sylvia. If is is only for a short time, get a cheap ceiling fan and bung it in a bit of thin mdf and have it suck in instead of out.Or whichever way you fancy. |
Nuisance fastners - winge
On Feb 11, 11:18*pm, Sylvia Else wrote:
On 11/02/2011 11:56 PM, kreed wrote: On Feb 11, 9:20 pm, Sylvia *wrote: On 11/02/2011 8:11 AM, ian field wrote: "Sylvia * *wrote in message ... On 10/02/2011 11:23 AM, Metro wrote: "Sylvia * * wrote in message ... I had occasion to dismantle a cheap pedestal fan the other day (Coles Home Collection). It hadn't failed, but I wanted to see how it was wired up (that's another story). The cover to the button panel was held in place by four screws which were identical except that two were philips head type, and the other two had a triangular socket in the head. I have bits to cope with most things I've encountered, but not those. What's the point? Are they worried about competition for repairing these $10 fans? Do consumers regularly electrocute themselves by taking fans apart without knowing what they're doing? Sylvia. They are only a tamperproof head of which there are various and easily available.. Wait until you come across a coffin head screw.I believe the reason for using them is that some countries prevent the dismantle of an appliance without the use of a tool or special tool so this way all fields are covered in one assembly. Did you find out how it worked. They are made to break. Best way to keep them longer is to keep the Blades clean and lubricate the bearings NOT with WD40 or the like. As I said, it hadn't broken. I was actually trying to figure out which wire was which leading to the induction motor. I had in mind making it run backwards. Aerofoils don't perform as well backwards, but they do perform. However, on further consideration I realised that the fan blades would be aerodynamically stalled if the fan ran backwards, with the result that it would probably not work much at all. If the fan is symetrical - snap off pairs of opposing blades. That's not going to fix the problem of the blades being stalled. What I would really need to do is fit the one-piece fan blade assembly on back to front (as well as reversing the motor), but the fan blade assembly is not designed to be attached the other way around. Sylvia. Might sound silly, but cant the entire fan head (including motor) be rotated 180 degrees, or do you want the air intake without the motor in the way ? The application is to suck cool air in through an open window at night. During the recent heat wave, it was noticeable that even though the temperature outside drops at night, the temperature of the house doesn't drop that much. The problem is lack of air flow. A conventional pedestal fan blows in such a direction that when it's placed as near as possible to a window, the fan blades are still quite a way from the cool air, and so the result is not as effective as it might be. If I could reverse the direction of flow, then I could also turn then fan around, so that the blades would be much closer to the window. I considered simply building a duct, but the cost of materials was excessive. I'm thinking of using box fans instead. Sylvia. We had the same problem, I put a Woolies pedestal fan right in front of the window on the inside, and used it that way. It works well, but I agree that if you could mount it in the open window directly it would work a lot better. Currently it sits about 25cm inside of the window opening due to the stand. The box fan would probably be a better idea. Could put a shelf or something under the window, and sit it on there. Another (depending on the amount of air these things move, their appearance, and the fact that the shaded pole motor and blade is exposed on the back) could be use bathroom type exhaust fan(s) mounted through a piece of plywood that sits in the open section of the window. ? If the window has a good height, you might be able to try one at the top blowing out the hot air and one at the bottom blowing in cool ? |
Nuisance fastners - winge
On Feb 11, 11:31*pm, F Murtz wrote:
Sylvia Else wrote: On 11/02/2011 11:56 PM, kreed wrote: On Feb 11, 9:20 pm, Sylvia wrote: On 11/02/2011 8:11 AM, ian field wrote: "Sylvia wrote in message ... On 10/02/2011 11:23 AM, Metro wrote: "Sylvia wrote in message ... I had occasion to dismantle a cheap pedestal fan the other day (Coles Home Collection). It hadn't failed, but I wanted to see how it was wired up (that's another story). The cover to the button panel was held in place by four screws which were identical except that two were philips head type, and the other two had a triangular socket in the head. I have bits to cope with most things I've encountered, but not those. What's the point? Are they worried about competition for repairing these $10 fans? Do consumers regularly electrocute themselves by taking fans apart without knowing what they're doing? Sylvia. They are only a tamperproof head of which there are various and easily available.. Wait until you come across a coffin head screw.I believe the reason for using them is that some countries prevent the dismantle of an appliance without the use of a tool or special tool so this way all fields are covered in one assembly. Did you find out how it worked. They are made to break. Best way to keep them longer is to keep the Blades clean and lubricate the bearings NOT with WD40 or the like. As I said, it hadn't broken. I was actually trying to figure out which wire was which leading to the induction motor. I had in mind making it run backwards. Aerofoils don't perform as well backwards, but they do perform. However, on further consideration I realised that the fan blades would be aerodynamically stalled if the fan ran backwards, with the result that it would probably not work much at all. If the fan is symetrical - snap off pairs of opposing blades. That's not going to fix the problem of the blades being stalled. What I would really need to do is fit the one-piece fan blade assembly on back to front (as well as reversing the motor), but the fan blade assembly is not designed to be attached the other way around. Sylvia. Might sound silly, but cant the entire fan head (including motor) be rotated 180 degrees, or do you want the air intake without the motor in the way ? The application is to suck cool air in through an open window at night. During the recent heat wave, it was noticeable that even though the temperature outside drops at night, the temperature of the house doesn't drop that much. The problem is lack of air flow. A conventional pedestal fan blows in such a direction that when it's placed as near as possible to a window, the fan blades are still quite a way from the cool air, and so the result is not as effective as it might be. If I could reverse the direction of flow, then I could also turn then fan around, so that the blades would be much closer to the window. I considered simply building a duct, but the cost of materials was excessive. I'm thinking of using box fans instead. Sylvia. If is is only for a short time, get a cheap ceiling fan and bung it in a bit of thin mdf and have it suck in instead of out.Or whichever way you fancy. While on the subject of ceiling fans, void those Arlec ones at Bunnings, they are flat out getting up any sort of airflow, and the motor is very lightweight. They are also the first fan I have ever seen that includes a "blade balancing kit" which includes a few flat pieces of steel and double sided tape for mounting them. Their highest speed setting is about the same as a lowest speed settings on your standard "airflow" ceiling fan that electricians usually install. |
Nuisance fastners - winge
kreed wrote:
On Feb 11, 11:31 pm, F wrote: Sylvia Else wrote: On 11/02/2011 11:56 PM, kreed wrote: On Feb 11, 9:20 pm, Sylvia wrote: On 11/02/2011 8:11 AM, ian field wrote: "Sylvia wrote in message ... On 10/02/2011 11:23 AM, Metro wrote: "Sylvia wrote in message ... I had occasion to dismantle a cheap pedestal fan the other day (Coles Home Collection). It hadn't failed, but I wanted to see how it was wired up (that's another story). The cover to the button panel was held in place by four screws which were identical except that two were philips head type, and the other two had a triangular socket in the head. I have bits to cope with most things I've encountered, but not those. What's the point? Are they worried about competition for repairing these $10 fans? Do consumers regularly electrocute themselves by taking fans apart without knowing what they're doing? Sylvia. They are only a tamperproof head of which there are various and easily available.. Wait until you come across a coffin head screw.I believe the reason for using them is that some countries prevent the dismantle of an appliance without the use of a tool or special tool so this way all fields are covered in one assembly. Did you find out how it worked. They are made to break. Best way to keep them longer is to keep the Blades clean and lubricate the bearings NOT with WD40 or the like. As I said, it hadn't broken. I was actually trying to figure out which wire was which leading to the induction motor. I had in mind making it run backwards. Aerofoils don't perform as well backwards, but they do perform. However, on further consideration I realised that the fan blades would be aerodynamically stalled if the fan ran backwards, with the result that it would probably not work much at all. If the fan is symetrical - snap off pairs of opposing blades. That's not going to fix the problem of the blades being stalled. What I would really need to do is fit the one-piece fan blade assembly on back to front (as well as reversing the motor), but the fan blade assembly is not designed to be attached the other way around. Sylvia. Might sound silly, but cant the entire fan head (including motor) be rotated 180 degrees, or do you want the air intake without the motor in the way ? The application is to suck cool air in through an open window at night. During the recent heat wave, it was noticeable that even though the temperature outside drops at night, the temperature of the house doesn't drop that much. The problem is lack of air flow. A conventional pedestal fan blows in such a direction that when it's placed as near as possible to a window, the fan blades are still quite a way from the cool air, and so the result is not as effective as it might be. If I could reverse the direction of flow, then I could also turn then fan around, so that the blades would be much closer to the window. I considered simply building a duct, but the cost of materials was excessive. I'm thinking of using box fans instead. Sylvia. If is is only for a short time, get a cheap ceiling fan and bung it in a bit of thin mdf and have it suck in instead of out.Or whichever way you fancy. While on the subject of ceiling fans, void those Arlec ones at Bunnings, they are flat out getting up any sort of airflow, and the motor is very lightweight. They are also the first fan I have ever seen that includes a "blade balancing kit" which includes a few flat pieces of steel and double sided tape for mounting them. Their highest speed setting is about the same as a lowest speed settings on your standard "airflow" ceiling fan that electricians usually install. I may have mislead people I meant ceiling exhaust fan |
Nuisance fastners - winge
On Sat, 12 Feb 2011 00:18:39 +1100, Sylvia Else
wrote: The application is to suck cool air in through an open window at night. During the recent heat wave, it was noticeable that even though the temperature outside drops at night, the temperature of the house doesn't drop that much. The problem is lack of air flow. A conventional pedestal fan blows in such a direction that when it's placed as near as possible to a window, the fan blades are still quite a way from the cool air, and so the result is not as effective as it might be. If I could reverse the direction of flow, then I could also turn then fan around, so that the blades would be much closer to the window. I considered simply building a duct, but the cost of materials was excessive. If we are talking temporary would some the use of some thickish polythene sheet and gaffa tape be out of the question (to 'join' the fan to the window opening)? We have a split unit aircon unit in the (unoccupied) middle bedroom but with all the bedroom doors open and the landing separated from the rest of the house via a temporary 'curtain of polythene sheet tacked to a baton and attached to the ceiling (by just 2 screws) works very well at cooling all the bedrooms. And no one here GsAF what it looked like, just that it worked ... hmmm, 18 Deg C Well, for the 2 weeks we call 'summer' here in the UK anyway. ;-) Cheers, T i m |
Nuisance fastners - winge
On 12/02/2011 12:38 AM, kreed wrote:
On Feb 11, 11:18 pm, Sylvia wrote: On 11/02/2011 11:56 PM, kreed wrote: On Feb 11, 9:20 pm, Sylvia wrote: On 11/02/2011 8:11 AM, ian field wrote: "Sylvia wrote in message ... On 10/02/2011 11:23 AM, Metro wrote: "Sylvia wrote in message ... I had occasion to dismantle a cheap pedestal fan the other day (Coles Home Collection). It hadn't failed, but I wanted to see how it was wired up (that's another story). The cover to the button panel was held in place by four screws which were identical except that two were philips head type, and the other two had a triangular socket in the head. I have bits to cope with most things I've encountered, but not those. What's the point? Are they worried about competition for repairing these $10 fans? Do consumers regularly electrocute themselves by taking fans apart without knowing what they're doing? Sylvia. They are only a tamperproof head of which there are various and easily available.. Wait until you come across a coffin head screw.I believe the reason for using them is that some countries prevent the dismantle of an appliance without the use of a tool or special tool so this way all fields are covered in one assembly. Did you find out how it worked. They are made to break. Best way to keep them longer is to keep the Blades clean and lubricate the bearings NOT with WD40 or the like. As I said, it hadn't broken. I was actually trying to figure out which wire was which leading to the induction motor. I had in mind making it run backwards. Aerofoils don't perform as well backwards, but they do perform. However, on further consideration I realised that the fan blades would be aerodynamically stalled if the fan ran backwards, with the result that it would probably not work much at all. If the fan is symetrical - snap off pairs of opposing blades. That's not going to fix the problem of the blades being stalled. What I would really need to do is fit the one-piece fan blade assembly on back to front (as well as reversing the motor), but the fan blade assembly is not designed to be attached the other way around. Sylvia. Might sound silly, but cant the entire fan head (including motor) be rotated 180 degrees, or do you want the air intake without the motor in the way ? The application is to suck cool air in through an open window at night. During the recent heat wave, it was noticeable that even though the temperature outside drops at night, the temperature of the house doesn't drop that much. The problem is lack of air flow. A conventional pedestal fan blows in such a direction that when it's placed as near as possible to a window, the fan blades are still quite a way from the cool air, and so the result is not as effective as it might be. If I could reverse the direction of flow, then I could also turn then fan around, so that the blades would be much closer to the window. I considered simply building a duct, but the cost of materials was excessive. I'm thinking of using box fans instead. Sylvia. We had the same problem, I put a Woolies pedestal fan right in front of the window on the inside, and used it that way. It works well, but I agree that if you could mount it in the open window directly it would work a lot better. Currently it sits about 25cm inside of the window opening due to the stand. The box fan would probably be a better idea. Could put a shelf or something under the window, and sit it on there. Another (depending on the amount of air these things move, their appearance, and the fact that the shaded pole motor and blade is exposed on the back) could be use bathroom type exhaust fan(s) mounted through a piece of plywood that sits in the open section of the window. ? If the window has a good height, you might be able to try one at the top blowing out the hot air and one at the bottom blowing in cool ? Perhaps, though one would have to be concerned that one just ended up creating a flow from the bottom to the top with little penetration into the room. Something to experiment with, I suppose. My thinking is to take two box fans, remove their feet, and attach them to a wooden frame that can be slotted into the groves normally used by the horizontally sliding window. It would make something that could be quickly attached as needed, and equally easily removed when not. Any spare window space would be blocked off, so that air pumped in would push other air out of the house wherever it could escape. BTW, I've been using a box fan to force ventilate an underhouse store room where he had something of a drain overflow. After running continously for a month, its bearings are stuffed. Me thinks they're not designed for that level of use. Sylvia. |
Nuisance fastners - winge
kreed wrote:
On Feb 11, 11:18 pm, Sylvia wrote: On 11/02/2011 11:56 PM, kreed wrote: On Feb 11, 9:20 pm, Sylvia wrote: On 11/02/2011 8:11 AM, ian field wrote: "Sylvia wrote in message ... On 10/02/2011 11:23 AM, Metro wrote: "Sylvia wrote in message ... I had occasion to dismantle a cheap pedestal fan the other day (Coles Home Collection). It hadn't failed, but I wanted to see how it was wired up (that's another story). The cover to the button panel was held in place by four screws which were identical except that two were philips head type, and the other two had a triangular socket in the head. I have bits to cope with most things I've encountered, but not those. What's the point? Are they worried about competition for repairing these $10 fans? Do consumers regularly electrocute themselves by taking fans apart without knowing what they're doing? Sylvia. They are only a tamperproof head of which there are various and easily available.. Wait until you come across a coffin head screw.I believe the reason for using them is that some countries prevent the dismantle of an appliance without the use of a tool or special tool so this way all fields are covered in one assembly. Did you find out how it worked. They are made to break. Best way to keep them longer is to keep the Blades clean and lubricate the bearings NOT with WD40 or the like. As I said, it hadn't broken. I was actually trying to figure out which wire was which leading to the induction motor. I had in mind making it run backwards. Aerofoils don't perform as well backwards, but they do perform. However, on further consideration I realised that the fan blades would be aerodynamically stalled if the fan ran backwards, with the result that it would probably not work much at all. If the fan is symetrical - snap off pairs of opposing blades. That's not going to fix the problem of the blades being stalled. What I would really need to do is fit the one-piece fan blade assembly on back to front (as well as reversing the motor), but the fan blade assembly is not designed to be attached the other way around. Sylvia. Might sound silly, but cant the entire fan head (including motor) be rotated 180 degrees, or do you want the air intake without the motor in the way ? The application is to suck cool air in through an open window at night. During the recent heat wave, it was noticeable that even though the temperature outside drops at night, the temperature of the house doesn't drop that much. The problem is lack of air flow. A conventional pedestal fan blows in such a direction that when it's placed as near as possible to a window, the fan blades are still quite a way from the cool air, and so the result is not as effective as it might be. If I could reverse the direction of flow, then I could also turn then fan around, so that the blades would be much closer to the window. I considered simply building a duct, but the cost of materials was excessive. I'm thinking of using box fans instead. Sylvia. We had the same problem, I put a Woolies pedestal fan right in front of the window on the inside, and used it that way. It works well, but I agree that if you could mount it in the open window directly it would work a lot better. Currently it sits about 25cm inside of the window opening due to the stand. The box fan would probably be a better idea. Could put a shelf or something under the window, and sit it on there. Another (depending on the amount of air these things move, their appearance, and the fact that the shaded pole motor and blade is exposed on the back) could be use bathroom type exhaust fan(s) mounted through a piece of plywood Dont know why I bother ,I new I was invisible. that sits in the open section of the window. ? If the window has a good height, you might be able to try one at the top blowing out the hot air and one at the bottom blowing in cool ? |
Nuisance fastners - winge
Sylvia Else wrote:
{...] A conventional pedestal fan blows in such a direction that when it's placed as near as possible to a window, the fan blades are still quite a way from the cool air, and so the result is not as effective as it might be. If I could reverse the direction of flow, then I could also turn then fan around, so that the blades would be much closer to the window. I considered simply building a duct, but the cost of materials was excessive. Cardboard box? -- ~ Adrian Tuddenham ~ (Remove the ".invalid"s and add ".co.uk" to reply) www.poppyrecords.co.uk |
Nuisance fastners - winge
"Sylvia Else" wrote in message ... On 11/02/2011 11:56 PM, kreed wrote: On Feb 11, 9:20 pm, Sylvia wrote: On 11/02/2011 8:11 AM, ian field wrote: "Sylvia wrote in message ... On 10/02/2011 11:23 AM, Metro wrote: "Sylvia wrote in message ... I had occasion to dismantle a cheap pedestal fan the other day (Coles Home Collection). It hadn't failed, but I wanted to see how it was wired up (that's another story). The cover to the button panel was held in place by four screws which were identical except that two were philips head type, and the other two had a triangular socket in the head. I have bits to cope with most things I've encountered, but not those. What's the point? Are they worried about competition for repairing these $10 fans? Do consumers regularly electrocute themselves by taking fans apart without knowing what they're doing? Sylvia. They are only a tamperproof head of which there are various and easily available.. Wait until you come across a coffin head screw.I believe the reason for using them is that some countries prevent the dismantle of an appliance without the use of a tool or special tool so this way all fields are covered in one assembly. Did you find out how it worked. They are made to break. Best way to keep them longer is to keep the Blades clean and lubricate the bearings NOT with WD40 or the like. As I said, it hadn't broken. I was actually trying to figure out which wire was which leading to the induction motor. I had in mind making it run backwards. Aerofoils don't perform as well backwards, but they do perform. However, on further consideration I realised that the fan blades would be aerodynamically stalled if the fan ran backwards, with the result that it would probably not work much at all. If the fan is symetrical - snap off pairs of opposing blades. That's not going to fix the problem of the blades being stalled. What I would really need to do is fit the one-piece fan blade assembly on back to front (as well as reversing the motor), but the fan blade assembly is not designed to be attached the other way around. Sylvia. Might sound silly, but cant the entire fan head (including motor) be rotated 180 degrees, or do you want the air intake without the motor in the way ? The application is to suck cool air in through an open window at night. During the recent heat wave, it was noticeable that even though the temperature outside drops at night, the temperature of the house doesn't drop that much. The problem is lack of air flow. A conventional pedestal fan blows in such a direction that when it's placed as near as possible to a window, the fan blades are still quite a way from the cool air, and so the result is not as effective as it might be. If I could reverse the direction of flow, then I could also turn then fan around, so that the blades would be much closer to the window. Stick the fan outside, blow the air inside. Lateral thinking is absent in the female of the species. I considered simply building a duct, but the cost of materials was excessive. Rubbish - use paper and glue - you obviously have plenty of time on your hands...... http://en.wikipedia.org/wiki/Papier-m%C3%A2ch%C3%A9 |
Nuisance fastners - winge
FWIW..
A motor with 2 identical windings in series, is a PSC permanent split capacitor motor. Electrically, in a PSC motor the windings are the same as a center-tapped transformer, having 3 leads. PSC motors can be run in either direction, and that's one of their unique features, a single-phase AC motor that can be instantly reversed (which single-phase AC motors generally can't do, without allowing them to stop before reversing). -- Cheers, WB .............. "Sylvia Else" wrote in message ... It's not shaded pole. It has two sets of windings perpendicular to each other, and a capacitor which I believe is in series with one set of windings. Sylvia. |
Nuisance fastners - winge
On 2/11/2011 3:57 PM, Wild_Bill wrote:
Electrically, in a PSC motor the windings are the same as a center-tapped transformer, having 3 leads. Does that mean it's two-phase? Sorry, couldn't resist. ;-) Jeff |
Nuisance fastners - winge
On 12/02/2011 8:28 AM, fritz wrote:
"Sylvia wrote in message ... On 11/02/2011 11:56 PM, kreed wrote: On Feb 11, 9:20 pm, Sylvia wrote: On 11/02/2011 8:11 AM, ian field wrote: "Sylvia wrote in message ... On 10/02/2011 11:23 AM, Metro wrote: "Sylvia wrote in message ... I had occasion to dismantle a cheap pedestal fan the other day (Coles Home Collection). It hadn't failed, but I wanted to see how it was wired up (that's another story). The cover to the button panel was held in place by four screws which were identical except that two were philips head type, and the other two had a triangular socket in the head. I have bits to cope with most things I've encountered, but not those. What's the point? Are they worried about competition for repairing these $10 fans? Do consumers regularly electrocute themselves by taking fans apart without knowing what they're doing? Sylvia. They are only a tamperproof head of which there are various and easily available.. Wait until you come across a coffin head screw.I believe the reason for using them is that some countries prevent the dismantle of an appliance without the use of a tool or special tool so this way all fields are covered in one assembly. Did you find out how it worked. They are made to break. Best way to keep them longer is to keep the Blades clean and lubricate the bearings NOT with WD40 or the like. As I said, it hadn't broken. I was actually trying to figure out which wire was which leading to the induction motor. I had in mind making it run backwards. Aerofoils don't perform as well backwards, but they do perform. However, on further consideration I realised that the fan blades would be aerodynamically stalled if the fan ran backwards, with the result that it would probably not work much at all. If the fan is symetrical - snap off pairs of opposing blades. That's not going to fix the problem of the blades being stalled. What I would really need to do is fit the one-piece fan blade assembly on back to front (as well as reversing the motor), but the fan blade assembly is not designed to be attached the other way around. Sylvia. Might sound silly, but cant the entire fan head (including motor) be rotated 180 degrees, or do you want the air intake without the motor in the way ? The application is to suck cool air in through an open window at night. During the recent heat wave, it was noticeable that even though the temperature outside drops at night, the temperature of the house doesn't drop that much. The problem is lack of air flow. A conventional pedestal fan blows in such a direction that when it's placed as near as possible to a window, the fan blades are still quite a way from the cool air, and so the result is not as effective as it might be. If I could reverse the direction of flow, then I could also turn then fan around, so that the blades would be much closer to the window. Stick the fan outside, blow the air inside. Lateral thinking is absent in the female of the species. I considered simply building a duct, but the cost of materials was excessive. Rubbish - use paper and glue - you obviously have plenty of time on your hands...... http://en.wikipedia.org/wiki/Papier-m%C3%A2ch%C3%A9 Do you have data for the structural properties? Also, a mathematical model of the pressure differential across an insect-screen? Sylvia. |
Nuisance fastners - winge
On 2/11/2011 8:18 AM, Sylvia Else wrote:
On 11/02/2011 11:56 PM, kreed wrote: On Feb 11, 9:20 pm, Sylvia wrote: On 11/02/2011 8:11 AM, ian field wrote: "Sylvia wrote in message n I'm thinking of using box fans instead. Sylvia. Don't you have window fans where you live? http://www.target.com/Lasko-Electric.../dp/B001VEFUPO You can get them here (USA) for $20 JC |
Nuisance fastners - winge
On Feb 12, 10:42*am, Archon wrote:
On 2/11/2011 8:18 AM, Sylvia Else wrote: On 11/02/2011 11:56 PM, kreed wrote: On Feb 11, 9:20 pm, Sylvia wrote: On 11/02/2011 8:11 AM, ian field wrote: "Sylvia wrote in message n I'm thinking of using box fans instead. Sylvia. Don't you have window fans where you live? http://www.target.com/Lasko-Electric...ndow/dp/B001VE... You can get them here (USA) for $20 JC Never seen them, but they would be perfect for what Sylvia wants to achieve I think. They are on Ebay, but all from the USA. Note that most modern Australian windows slide horizontally - as long as this works sideways and will fit the opening, should be fine. |
Nuisance fastners - winge
On 12/02/2011 11:54 AM, kreed wrote:
On Feb 12, 10:42 am, wrote: On 2/11/2011 8:18 AM, Sylvia Else wrote: On 11/02/2011 11:56 PM, kreed wrote: On Feb 11, 9:20 pm, Sylvia wrote: On 11/02/2011 8:11 AM, ian field wrote: "Sylvia wrote in message n I'm thinking of using box fans instead. Sylvia. Don't you have window fans where you live? http://www.target.com/Lasko-Electric...ndow/dp/B001VE... You can get them here (USA) for $20 JC Never seen them, but they would be perfect for what Sylvia wants to achieve I think. They are on Ebay, but all from the USA. I found Lasko's web site. None of the instruction sheets (which I thought might specify the power) seem to exist. So I emailed the webadmin whose address was given on the web site. That email address appears not to exist either (it bounced). I hope they're better at making fans than they are at maintaining web sites. Sylvia. |
Nuisance fastners - winge
On Feb 12, 11:19*am, Sylvia Else wrote:
On 12/02/2011 11:54 AM, kreed wrote: On Feb 12, 10:42 am, *wrote: On 2/11/2011 8:18 AM, Sylvia Else wrote: *On 11/02/2011 11:56 PM, kreed wrote: On Feb 11, 9:20 pm, Sylvia *wrote: On 11/02/2011 8:11 AM, ian field wrote: "Sylvia *wrote in message n I'm thinking of using box fans instead. Sylvia. Don't you have window fans where you live? http://www.target.com/Lasko-Electric...ndow/dp/B001VE.... You can get them here (USA) for $20 JC Never seen them, but they would be perfect for what Sylvia wants to achieve I think. They are on Ebay, but all from the USA. I found Lasko's web site. None of the instruction sheets (which I thought might specify the power) seem to exist. So I emailed the webadmin whose address was given on the web site. That email address appears not to exist either (it bounced). I hope they're better at making fans than they are at maintaining web sites. Sylvia. These fans are also available on Ebay - search "window fan" and "outside australia" and there are several identical models. The sellers might be able to help ? |
Nuisance fastners - winge
On 12/02/2011 12:28 PM, kreed wrote:
On Feb 12, 11:19 am, Sylvia wrote: On 12/02/2011 11:54 AM, kreed wrote: On Feb 12, 10:42 am, wrote: On 2/11/2011 8:18 AM, Sylvia Else wrote: On 11/02/2011 11:56 PM, kreed wrote: On Feb 11, 9:20 pm, Sylvia wrote: On 11/02/2011 8:11 AM, ian field wrote: "Sylvia wrote in message n I'm thinking of using box fans instead. Sylvia. Don't you have window fans where you live? http://www.target.com/Lasko-Electric...ndow/dp/B001VE... You can get them here (USA) for $20 JC Never seen them, but they would be perfect for what Sylvia wants to achieve I think. They are on Ebay, but all from the USA. I found Lasko's web site. None of the instruction sheets (which I thought might specify the power) seem to exist. So I emailed the webadmin whose address was given on the web site. That email address appears not to exist either (it bounced). I hope they're better at making fans than they are at maintaining web sites. Sylvia. These fans are also available on Ebay - search "window fan" and "outside australia" and there are several identical models. The sellers might be able to help ? I presume I'd need to buy a step down transformer, and then there's the issue of the different frequency. Sylvia. |
Nuisance fastners - winge
On 2011-02-11, Sylvia Else wrote:
A conventional pedestal fan blows in such a direction that when it's placed as near as possible to a window, the fan blades are still quite a way from the cool air, and so the result is not as effective as it might be. If I could reverse the direction of flow, then I could also turn then fan around, so that the blades would be much closer to the window. I considered simply building a duct, but the cost of materials was excessive. I guess you didn't consider cardboard and packing tape then :) or a cheap plastic bucket? -- š‚šƒ 100% natural --- news://freenews.netfront.net/ - complaints: --- |
Nuisance fastners - winge
On 12/02/2011 2:43 PM, Jasen Betts wrote:
On 2011-02-11, Sylvia wrote: A conventional pedestal fan blows in such a direction that when it's placed as near as possible to a window, the fan blades are still quite a way from the cool air, and so the result is not as effective as it might be. If I could reverse the direction of flow, then I could also turn then fan around, so that the blades would be much closer to the window. I considered simply building a duct, but the cost of materials was excessive. I guess you didn't consider cardboard and packing tape then :) or a cheap plastic bucket? The fan is too big for a plastic bucket. I considered cardboard but it was far from clear to me that it was going to be strong enough without bracing that would further complicate the task. This isn't a research project. I was looking for a solution that would definitely work, and be robust. Sylvia. |
Nuisance fastners - winge
On 12/02/2011 3:03 PM, atec77 wrote:
On 12/02/2011 1:43 PM, Jasen Betts wrote: On 2011-02-11, Sylvia wrote: A conventional pedestal fan blows in such a direction that when it's placed as near as possible to a window, the fan blades are still quite a way from the cool air, and so the result is not as effective as it might be. If I could reverse the direction of flow, then I could also turn then fan around, so that the blades would be much closer to the window. I considered simply building a duct, but the cost of materials was excessive. I guess you didn't consider cardboard and packing tape then :) or a cheap plastic bucket? I can think of another use for a bucket in sylivas case Yes, I can use it to throw-up into whenever I imagine your face. Sylvia. |
| All times are GMT +1. The time now is 04:45 PM. |
|
Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004 - 2014 DIYbanter