Home |
Search |
Today's Posts |
|
Electronics Repair (sci.electronics.repair) Discussion of repairing electronic equipment. Topics include requests for assistance, where to obtain servicing information and parts, techniques for diagnosis and repair, and annecdotes about success, failures and problems. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
#1
Posted to sci.electronics.repair
|
|||
|
|||
Fuse Failure Machanism ...??
How do three fuses fail simultaneously ? I have just repaired a small
external switcher from an LCD TV for one of my trade customers. 12V @ 5A - you know the sort of thing. It had two 2.5A Wickman fuses just south of the line input connector, so that's one each in the live and neutral feeds. It also had a 3A plugtop fuse fitted, this being in the UK. So that's three fuses all effectively in series. Two of them directly so, and one in the other (return) side of the input circuit. All three were open, and the cause of this appeared to be that the main filter cap was bulged and open, although I'm not entirely sure why this should have led to excess input current, as I have seen open main filter caps many times, and fuse failure from this alone, is not the usual symptom. However, vagaries of switcher behaviour aside, how can three fuses - especially considering that one of them is a higher rated plugtop fuse, not known for their accuracy - that are all in series, all be open ? Clearly, as soon as one fails, in theory at least, all current through the other two is interupted ... As soon as the cap and three fuses were replaced, operation of the supply was normal, and it powered the TV without issue. Thoughts anyone ? Arfa |
#2
Posted to sci.electronics.repair
|
|||
|
|||
Fuse Failure Machanism ...??
On Mon, 7 Sep 2009 13:11:51 +0100, "Arfa Daily"
wrote: How do three fuses fail simultaneously ? I have just repaired a small external switcher from an LCD TV for one of my trade customers. 12V @ 5A - you know the sort of thing. It had two 2.5A Wickman fuses just south of the line input connector, so that's one each in the live and neutral feeds. It also had a 3A plugtop fuse fitted, this being in the UK. So that's three fuses all effectively in series. Two of them directly so, and one in the other (return) side of the input circuit. All three were open, and the cause of this appeared to be that the main filter cap was bulged and open, although I'm not entirely sure why this should have led to excess input current, as I have seen open main filter caps many times, and fuse failure from this alone, is not the usual symptom. However, vagaries of switcher behaviour aside, how can three fuses - especially considering that one of them is a higher rated plugtop fuse, not known for their accuracy - that are all in series, all be open ? Clearly, as soon as one fails, in theory at least, all current through the other two is interupted ... As soon as the cap and three fuses were replaced, operation of the supply was normal, and it powered the TV without issue. Thoughts anyone ? Arfa If you were here in the US midwest, I would say it was a nearby lightning strike and the fuses kept arcing after the first one opened. Anything like that possible in your area? |
#3
Posted to sci.electronics.repair
|
|||
|
|||
Fuse Failure Machanism ...??
On Mon, 7 Sep 2009 13:11:51 +0100, "Arfa Daily"
wrote: How do three fuses fail simultaneously ? I have just repaired a small external switcher from an LCD TV for one of my trade customers. 12V @ 5A - you know the sort of thing. It had two 2.5A Wickman fuses just south of the line input connector, so that's one each in the live and neutral feeds. It also had a 3A plugtop fuse fitted, this being in the UK. So that's three fuses all effectively in series. Two of them directly so, and one in the other (return) side of the input circuit. All three were open, and the cause of this appeared to be that the main filter cap was bulged and open, although I'm not entirely sure why this should have led to excess input current, as I have seen open main filter caps many times, and fuse failure from this alone, is not the usual symptom. However, vagaries of switcher behaviour aside, how can three fuses - especially considering that one of them is a higher rated plugtop fuse, not known for their accuracy - that are all in series, all be open ? Clearly, as soon as one fails, in theory at least, all current through the other two is interupted ... As soon as the cap and three fuses were replaced, operation of the supply was normal, and it powered the TV without issue. Thoughts anyone ? Arfa I can only say: good fuses! g A massive overcurrent, I'm sure, will blow all. I've seen two blow like this, I suspect one fails, but the failure arc is enough to cause the other (compromised at this point) to blow as well. |
#4
Posted to sci.electronics.repair
|
|||
|
|||
Fuse Failure Machanism ...??
The lightning strikes sounds plausible.
I think there's another possibility... Suppose the overload were enough to severely _bend_ the fuses, rather than blow them outright. When one finally popped, the others flexed back and cracked. So... Are they clear glass? Do you seen vaporized metal? Another possibility is that the overload was _so_ severe that they really _did_ all blow at the same time. The fuse wire, however small it is, has thermal inertia. It can still break, even after the power has been removed, if it was hot enough a millisecond or two before. Regardless, it's an interesting question. |
#5
Posted to sci.electronics.repair
|
|||
|
|||
Fuse Failure Machanism ...??
On Mon, 7 Sep 2009 13:11:51 +0100, "Arfa Daily"
wrote: It had two 2.5A Wickman fuses just south of the line input connector, so that's one each in the live and neutral feeds. Are those slo-blow fuses? If the fuse case is clear, it will show a spring and a resitor inside. If it is a slow blow, these take a while to open after seeing an overload. It depends on the amount of overload and resistor heating. There's a small delay during which time the other fuses are also receiving the full benefit of the overload. Even if the load is removed during this time, thermal inertia (the time it take for heat to make it from the resistor to the fuse melt area) will cause the other fuses to blow. However, if it's NOT a slo-blow fuse, then there's insufficient mass in the fuse wire to produce any thermal inertia effects, so this mechanism is unlikely. -- Jeff Liebermann 150 Felker St #D http://www.LearnByDestroying.com Santa Cruz CA 95060 http://802.11junk.com Skype: JeffLiebermann AE6KS 831-336-2558 |
#6
Posted to sci.electronics.repair
|
|||
|
|||
Fuse Failure Machanism ...??
"Jeff Liebermann" wrote in message ... On Mon, 7 Sep 2009 13:11:51 +0100, "Arfa Daily" wrote: It had two 2.5A Wickman fuses just south of the line input connector, so that's one each in the live and neutral feeds. Are those slo-blow fuses? If the fuse case is clear, it will show a spring and a resitor inside. If it is a slow blow, these take a while to open after seeing an overload. It depends on the amount of overload and resistor heating. There's a small delay during which time the other fuses are also receiving the full benefit of the overload. Even if the load is removed during this time, thermal inertia (the time it take for heat to make it from the resistor to the fuse melt area) will cause the other fuses to blow. However, if it's NOT a slo-blow fuse, then there's insufficient mass in the fuse wire to produce any thermal inertia effects, so this mechanism is unlikely. -- Jeff Liebermann Ok. Few points from various people to answer here. The lightning strike scenario is a possibility. There have been a couple of storms in the area in the last few weeks, but in general, it's been a pretty quiet season here in the UK this year. The O/C main filter cap might just be a red herring here. I must admit that I replaced it at the same time as the fuses, as it was obviously bulging both top and bottom, and read open on the ESR meter. It could be that it was on its last legs ESR-wise, but still had enough 'guts' to perform its basic function, until the surge that took the fuses out, finished it off. That might add support to the lightning strike theory. As to the fuse types. I take it the term "Wickman fuse" doesn't have any meaning in the U.S.? If not, allow me to explain. Wickmans are a type of wire-ended fuse for direct PCB mounting. They are a plastic cylinder about 10mm diameter and maybe 10 -12mm high. They have two leads coming out of the bottom pitched at probably 5mm. Imagine a small stubby radial leaded electrolytic, if you like. The plastic is usually either black or brown. They have always been popular in Philips gear, although other manufacturers do use them. They come in both fast and "T" rated types. The ones that were fitted in this particular supply, were "T" type, so yes, slo-blo's. However, with them being plastic, you get no indications of how they have failed. I am of course very familiar with the three normal failure modes of vapourised, melted, and broken, and if you could see how these had failed, I'm sure it would have given a clue as to what was going on. To be honest, I'm not even sure of how these fuses are constructed internally. I might try and break into one tomorrow to get a look. As to the plugtop fuse, these are ceramic bodied, so again, you can't see the failure mode. I guess you might not have ever even seen one in the U.S. I've no idea what the fusing characteristic of them is. They come in 3A, 5A, 10A and 13A flavours, but most people would consider them to be little more than a calibrated nail. I have seen them stand up to overloads where you could almost hear the substation transformer jumping off its mountings, and yet they will also readily fail when a light bulb pops its clogs. I quite like the thermal inertia idea as an explanation, but even though the Wickmans are "T" rated, I'm not sure that there is sufficient wire in that little case (assuming that it is in some way a 'conventional' wire fuse inside) to actually have that much inertia ... Thanks all for your thoughts (including bz who responded (accidentally ?) directly to me). It's an interesting little puzzle. Arfa |
#8
Posted to sci.electronics.repair
|
|||
|
|||
Fuse Failure Machanism ...??
"Ross Herbert" wrote in message ... On Tue, 8 Sep 2009 01:53:05 +0100, "Arfa Daily" wrote: : :"Jeff Liebermann" wrote in message .. . : On Mon, 7 Sep 2009 13:11:51 +0100, "Arfa Daily" : wrote: : :It had two 2.5A Wickman fuses just south of the :line input connector, so that's one each in the live and neutral feeds. : : Are those slo-blow fuses? If the fuse case is clear, it will show a : spring and a resitor inside. : : If it is a slow blow, these take a while to open after seeing an : overload. It depends on the amount of overload and resistor heating. : There's a small delay during which time the other fuses are also : receiving the full benefit of the overload. Even if the load is : removed during this time, thermal inertia (the time it take for heat : to make it from the resistor to the fuse melt area) will cause the : other fuses to blow. : : However, if it's NOT a slo-blow fuse, then there's insufficient mass : in the fuse wire to produce any thermal inertia effects, so this : mechanism is unlikely. : : : : -- : Jeff Liebermann : : :Ok. Few points from various people to answer here. The lightning strike :scenario is a possibility. There have been a couple of storms in the area in :the last few weeks, but in general, it's been a pretty quiet season here in :the UK this year. The O/C main filter cap might just be a red herring here. :I must admit that I replaced it at the same time as the fuses, as it was bviously bulging both top and bottom, and read open on the ESR meter. It :could be that it was on its last legs ESR-wise, but still had enough 'guts' :to perform its basic function, until the surge that took the fuses out, :finished it off. That might add support to the lightning strike theory. : :As to the fuse types. I take it the term "Wickman fuse" doesn't have any :meaning in the U.S.? If not, allow me to explain. Wickmans are a type of :wire-ended fuse for direct PCB mounting. They are a plastic cylinder about :10mm diameter and maybe 10 -12mm high. They have two leads coming out of the :bottom pitched at probably 5mm. Imagine a small stubby radial leaded :electrolytic, if you like. The plastic is usually either black or brown. :They have always been popular in Philips gear, although other manufacturers :do use them. They come in both fast and "T" rated types. The ones that were :fitted in this particular supply, were "T" type, so yes, slo-blo's. However, :with them being plastic, you get no indications of how they have failed. I :am of course very familiar with the three normal failure modes of :vapourised, melted, and broken, and if you could see how these had failed, :I'm sure it would have given a clue as to what was going on. To be honest, :I'm not even sure of how these fuses are constructed internally. I might try :and break into one tomorrow to get a look. : :As to the plugtop fuse, these are ceramic bodied, so again, you can't see :the failure mode. I guess you might not have ever even seen one in the U.S. :I've no idea what the fusing characteristic of them is. They come in 3A, 5A, :10A and 13A flavours, but most people would consider them to be little more :than a calibrated nail. I have seen them stand up to overloads where you :could almost hear the substation transformer jumping off its mountings, and :yet they will also readily fail when a light bulb pops its clogs. : :I quite like the thermal inertia idea as an explanation, but even though the :Wickmans are "T" rated, I'm not sure that there is sufficient wire in that :little case (assuming that it is in some way a 'conventional' wire fuse :inside) to actually have that much inertia ... : :Thanks all for your thoughts (including bz who responded (accidentally ?) :directly to me). It's an interesting little puzzle. : :Arfa : I would be more concerned with what caused the filter cap to bulge... If it is a well known brand and correctly rated for the application then it should not have degenerated to that state as long as normal input voltage range was experienced. I also doubt that a possible short term lightning event would have caused the cap to bulge - this symptom is more likely due to a longer term overvoltage event. If all the major input circuitry and components are ok I would suspect a leaky diode in the bridge rectifier. Presumably, you don't see too many small high current switchers ? This is a small supply - probably around 6" x 3" x 1.5", and fully enclosed in a plastic case. The cap in question was a CapXon 120uF at 450v, and a 105 deg type, so a common enough make, more than adequately rated for the job. As is ever the case, it is the way that the designer has used it, that has led to its demise. It was layed over flat on the board, jammed in by the heatsink that carries the secondary side reccies etc. This is a very typical scenario, which anyone who works with them a lot, will tell you leads to drying out, bulging, and ultimate failure. I'm not sure where you got it from that a lightning event was thought to be responsible for this bulging, Ross. I don't think I actually said that. The supply was dead as received. When I opened it up, the cap was obviously bulging, and very 'tired' looking, as I think I said. When checked, the two Wickman fuses in the front end, were both open. Without thinking too much about it, I associated the two 'problems', and went ahead and replaced all three items. When the supply still didn't work, I checked the input volts, and there wasn't any, because the plugtop fuse had also failed. It was only then that I started to question exactly what the failure mechanism had been, and how, or even *if* the cap had in some way been responsible. I came to the conclusion that the two sets of failures might be unrelated. Clearly, before the supply failed completely, the main filter cap must have been working to a degree, allbeit in its bulged condition, which I'm quite sure was a long term thing caused by poor ventillation and positioning. It really *is* a very common occurence, which most often is due to poor mechanical design of a supply, and rarely anything to do with defective bridges in my day to day experience. I have of course had leaky diodes in bridges, but I normally find that they tend to produce more catastrophic failures than just a gently cooking cap. I must say that I didn't check the bridge specifically for this. I guess it will soon come bouncing back, if there is any such problem ... :-) For all I know, the cap might still have been working enough to run the supply. As I had already replaced it, I guess we'll never know. When I checked it, it was only on the ESR meter, and only a quick check, as it was obviously in a bit of a state. It might not have been totally open, just outside the measurement range of the meter. The only place then, that the lightning came into it, was that I thought that as the cap might have been at *almost* the point of total failure from its slow heat degeneration, a large surge might have been enough to take it that last gasp to failure. Thanks for you input anyway. It's all interesting stuff. Arfa |
#9
Posted to sci.electronics.repair
|
|||
|
|||
Fuse Failure Machanism ...??
Arfa Daily wrote in message
... "Jeff Liebermann" wrote in message ... On Mon, 7 Sep 2009 13:11:51 +0100, "Arfa Daily" wrote: It had two 2.5A Wickman fuses just south of the line input connector, so that's one each in the live and neutral feeds. Are those slo-blow fuses? If the fuse case is clear, it will show a spring and a resitor inside. If it is a slow blow, these take a while to open after seeing an overload. It depends on the amount of overload and resistor heating. There's a small delay during which time the other fuses are also receiving the full benefit of the overload. Even if the load is removed during this time, thermal inertia (the time it take for heat to make it from the resistor to the fuse melt area) will cause the other fuses to blow. However, if it's NOT a slo-blow fuse, then there's insufficient mass in the fuse wire to produce any thermal inertia effects, so this mechanism is unlikely. -- Jeff Liebermann Ok. Few points from various people to answer here. The lightning strike scenario is a possibility. There have been a couple of storms in the area in the last few weeks, but in general, it's been a pretty quiet season here in the UK this year. The O/C main filter cap might just be a red herring here. I must admit that I replaced it at the same time as the fuses, as it was obviously bulging both top and bottom, and read open on the ESR meter. It could be that it was on its last legs ESR-wise, but still had enough 'guts' to perform its basic function, until the surge that took the fuses out, finished it off. That might add support to the lightning strike theory. As to the fuse types. I take it the term "Wickman fuse" doesn't have any meaning in the U.S.? If not, allow me to explain. Wickmans are a type of wire-ended fuse for direct PCB mounting. They are a plastic cylinder about 10mm diameter and maybe 10 -12mm high. They have two leads coming out of the bottom pitched at probably 5mm. Imagine a small stubby radial leaded electrolytic, if you like. The plastic is usually either black or brown. They have always been popular in Philips gear, although other manufacturers do use them. They come in both fast and "T" rated types. The ones that were fitted in this particular supply, were "T" type, so yes, slo-blo's. However, with them being plastic, you get no indications of how they have failed. I am of course very familiar with the three normal failure modes of vapourised, melted, and broken, and if you could see how these had failed, I'm sure it would have given a clue as to what was going on. To be honest, I'm not even sure of how these fuses are constructed internally. I might try and break into one tomorrow to get a look. As to the plugtop fuse, these are ceramic bodied, so again, you can't see the failure mode. I guess you might not have ever even seen one in the U.S. I've no idea what the fusing characteristic of them is. They come in 3A, 5A, 10A and 13A flavours, but most people would consider them to be little more than a calibrated nail. I have seen them stand up to overloads where you could almost hear the substation transformer jumping off its mountings, and yet they will also readily fail when a light bulb pops its clogs. I quite like the thermal inertia idea as an explanation, but even though the Wickmans are "T" rated, I'm not sure that there is sufficient wire in that little case (assuming that it is in some way a 'conventional' wire fuse inside) to actually have that much inertia ... Thanks all for your thoughts (including bz who responded (accidentally ?) directly to me). It's an interesting little puzzle. Arfa As far as mains glass-barrel fuses , its annoying when the owner throws away the blown fuse. Inspection can tell a lot, from 2 remaining sagged pieces of wire with a small break in the middle, could be due to fair wear and tear in effect, sagging over time and current carrying capacity going down over time. via still extant wires at the ends and one molten ball , no blacking (x2 or so overload) via a few sputter balls in the tube , some blacking (x5 or so overload ?) to totally black and cracked glass ( x10 overload?) Its so long since I came across a Wickman I don't remember if I ground into/cracked it to explore its construction/ failure character. -- Diverse Devices, Southampton, England electronic hints and repair briefs , schematics/manuals list on http://home.graffiti.net/diverse:graffiti.net/ |
#10
Posted to sci.electronics.repair
|
|||
|
|||
Fuse Failure Machanism ...??
Genrad 1659 RLC tester (Quadtech ) use them, which are American I think. Now
I remember it was very short duration overlaods, from static discharges, that kept blowing them ,showing as very neat breaks as though cut with endsnips. After active stuff had been destroyed of course If anyone knows the USA term I will add to my translator http://www.divdev.fsnet.co.uk/tool_terms.htm -- Diverse Devices, Southampton, England electronic hints and repair briefs , schematics/manuals list on http://home.graffiti.net/diverse:graffiti.net/ |
#11
Posted to sci.electronics.repair
|
|||
|
|||
Fuse Failure Machanism ...??
"Arfa Daily" wrote in message ... When checked, the two Wickman fuses in the front end, were both open. Without thinking too much about it, I associated the two 'problems', and went ahead and replaced all three items. When the supply still didn't work, I checked the input volts, and there wasn't any, because the plugtop fuse had also failed. Arfa Arfa, I always used to check the plug top fuse first even though the customer invariably said that they had tried the fuse. In my experience customers never throw a ceramic plug top fuse away even the blown ones. They usually end up in a drawer to be tried again just in case it wasnt faulty! Not to mention the people who fit 13 Amp fuses to everything, or worse, wrap the fuse in tinfoil. Roy |
#12
Posted to sci.electronics.repair
|
|||
|
|||
Fuse Failure Machanism ...??
N_Cook wrote:
If anyone knows the USA term I will add to my translator http://www.divdev.fsnet.co.uk/tool_terms.htm I don't know of a standard term, but browsing through DigiKey datasheets, the terms 'subminiature', 'micro', 'cartridge', and 'IEC 60127-3' are commonly used. Littlefuse/Wickmann: http://www.littelfuse.com/data/en/Da..._LF_011906.pdf Littlefuse: http://media.digikey.com/pdf/Data%20.../663SERIES.pdf Belfuse: http://www.belfuse.com/Data/Datasheets/MRT.pdf Cooper/Bussmann: http://www.cooperbussmann.com/pdf/12...75cdc90d96.pdf Schurter: http://www.schurterinc.com/pdf/english/typ_mst_250.pdf I've seen similar fuses on PCI extender/debug cards. TM |
#13
Posted to sci.electronics.repair
|
|||
|
|||
Fuse Failure Machanism ...??
On Tue, 8 Sep 2009 09:48:47 +0100, "Arfa Daily" wrote:
: :"Ross Herbert" wrote in message .. . SNIP : : I would be more concerned with what caused the filter cap to bulge... : : If it is a well known brand and correctly rated for the application then : it : should not have degenerated to that state as long as normal input voltage : range : was experienced. I also doubt that a possible short term lightning event : would : have caused the cap to bulge - this symptom is more likely due to a longer : term : overvoltage event. : : If all the major input circuitry and components are ok I would suspect a : leaky : diode in the bridge rectifier. : :Presumably, you don't see too many small high current switchers ? Not in the last few months. No. However I was repairing small and large SMPS quite frequently in the past. The symptoms you described are exactly the same as I found in small 5" x 3" format SMPS I recently repaired, although there was only one series fuse and a current inrush limiter - both of which had died. The main filter cap was also bulging, as in your case, and the fault was traced to a dud diode in the bridge rectifier. The suggestion was made as a possibility since I can't actually see the unit myself and all particulars were not disclosed initially. :This is a :small supply - probably around 6" x 3" x 1.5", and fully enclosed in a lastic case. The cap in question was a CapXon 120uF at 450v, and a 105 deg :type, so a common enough make, more than adequately rated for the job. As is :ever the case, it is the way that the designer has used it, that has led to :its demise. It was layed over flat on the board, jammed in by the heatsink :that carries the secondary side reccies etc. This is a very typical :scenario, which anyone who works with them a lot, will tell you leads to :drying out, bulging, and ultimate failure. The fully enclosed nature of your unit does help to explain a possible reason for long term heating as a possible cause for the cap bulging. Pity you didn't include those details before since it is well known that heat is a major killer of caps in SMPS. : :I'm not sure where you got it from that a lightning event was thought to be :responsible for this bulging, Ross. I don't think I actually said that. The lightning suggestion was offered by in his response and that is what I was referring to. :The :supply was dead as received. When I opened it up, the cap was obviously :bulging, and very 'tired' looking, as I think I said. When checked, the two :Wickman fuses in the front end, were both open. Without thinking too much :about it, I associated the two 'problems', and went ahead and replaced all :three items. When the supply still didn't work, I checked the input volts, :and there wasn't any, because the plugtop fuse had also failed. It was only :then that I started to question exactly what the failure mechanism had been, :and how, or even *if* the cap had in some way been responsible. I came to :the conclusion that the two sets of failures might be unrelated. Clearly, :before the supply failed completely, the main filter cap must have been :working to a degree, allbeit in its bulged condition, which I'm quite sure :was a long term thing caused by poor ventillation and positioning. It really :*is* a very common occurence, which most often is due to poor mechanical :design of a supply, and rarely anything to do with defective bridges in my :day to day experience. I have of course had leaky diodes in bridges, but I :normally find that they tend to produce more catastrophic failures than just :a gently cooking cap. I must say that I didn't check the bridge specifically :for this. I guess it will soon come bouncing back, if there is any such roblem ... :-) : :For all I know, the cap might still have been working enough to run the :supply. As I had already replaced it, I guess we'll never know. When I :checked it, it was only on the ESR meter, and only a quick check, as it was bviously in a bit of a state. It might not have been totally open, just utside the measurement range of the meter. The only place then, that the :lightning came into it, was that I thought that as the cap might have been :at *almost* the point of total failure from its slow heat degeneration, a :large surge might have been enough to take it that last gasp to failure. : :Thanks for you input anyway. It's all interesting stuff. : :Arfa : |
#14
Posted to sci.electronics.repair
|
|||
|
|||
Fuse Failure Machanism ...??
Tony Matt wrote in message
... N_Cook wrote: If anyone knows the USA term I will add to my translator http://www.divdev.fsnet.co.uk/tool_terms.htm I don't know of a standard term, but browsing through DigiKey datasheets, the terms 'subminiature', 'micro', 'cartridge', and 'IEC 60127-3' are commonly used. Littlefuse/Wickmann: http://www.littelfuse.com/data/en/Da..._LF_011906.pdf Littlefuse: http://media.digikey.com/pdf/Data%20.../663SERIES.pdf Belfuse: http://www.belfuse.com/Data/Datasheets/MRT.pdf Cooper/Bussmann: http://www.cooperbussmann.com/pdf/12...75cdc90d96.pdf Schurter: http://www.schurterinc.com/pdf/english/typ_mst_250.pdf I've seen similar fuses on PCI extender/debug cards. TM I will go with IEC 60127-3, Littelfuse 369 series incidently ( Littelfuse & Wickman spellings) -- Diverse Devices, Southampton, England electronic hints and repair briefs , schematics/manuals list on http://home.graffiti.net/diverse:graffiti.net/ |
#15
Posted to sci.electronics.repair
|
|||
|
|||
Fuse Failure Machanism ...??
"Ross Herbert" wrote in message ... On Tue, 8 Sep 2009 09:48:47 +0100, "Arfa Daily" wrote: : :"Ross Herbert" wrote in message .. . SNIP : : I would be more concerned with what caused the filter cap to bulge... : : If it is a well known brand and correctly rated for the application then : it : should not have degenerated to that state as long as normal input voltage : range : was experienced. I also doubt that a possible short term lightning event : would : have caused the cap to bulge - this symptom is more likely due to a longer : term : overvoltage event. : : If all the major input circuitry and components are ok I would suspect a : leaky : diode in the bridge rectifier. : :Presumably, you don't see too many small high current switchers ? Not in the last few months. No. However I was repairing small and large SMPS quite frequently in the past. The symptoms you described are exactly the same as I found in small 5" x 3" format SMPS I recently repaired, although there was only one series fuse and a current inrush limiter - both of which had died. The main filter cap was also bulging, as in your case, and the fault was traced to a dud diode in the bridge rectifier. The suggestion was made as a possibility since I can't actually see the unit myself and all particulars were not disclosed initially. :This is a :small supply - probably around 6" x 3" x 1.5", and fully enclosed in a lastic case. The cap in question was a CapXon 120uF at 450v, and a 105 deg :type, so a common enough make, more than adequately rated for the job. As is :ever the case, it is the way that the designer has used it, that has led to :its demise. It was layed over flat on the board, jammed in by the heatsink :that carries the secondary side reccies etc. This is a very typical :scenario, which anyone who works with them a lot, will tell you leads to :drying out, bulging, and ultimate failure. The fully enclosed nature of your unit does help to explain a possible reason for long term heating as a possible cause for the cap bulging. Pity you didn't include those details before since it is well known that heat is a major killer of caps in SMPS. Sorry Ross - wasn't getting at you. When I said "presumably you don't see ....etc" I was being quite genuine in asking. Although I didn't specifically say that it was a fully enclosed type, I did say in the original post that it was "...a small external switcher from an LCD TV." I assumed that anyone who was regularly involved in the repair of such items, would immediately recognise that description as being a small, plastic, fully enclosed type. Interesting that you had identical symptoms on a similar one, and that you actually found a leaky diode in the bridge. Can you from memory, put a value on the amount of leakage ? I figure it must have been quite small, as any leaky bridges I've had, have had a much more catastrophic effect than just over-working the main filter cap for long enough to dry it out. I was originally thinking U.S. 110v input and whether the reduced voltage might allow such a leak to fester away without exploding anything, but thinking about it some more, you're in Aus-land aren't you ? Line voltage nominally 230 - ish same as here in the U.K. ?? : :I'm not sure where you got it from that a lightning event was thought to be :responsible for this bulging, Ross. I don't think I actually said that. The lightning suggestion was offered by in his response and that is what I was referring to. Ah, OK. I misunderstood you. I thought that you thought that I thought ( !!! ) that the lightning had led to the bulging. I was actually not associating the bulging with any lightning event, but considering the possibility that a surge on the line voltage from a nearby strike, as suggested by the poster that you cite, might have been responsible for the failure of the fuses, and for possibly 'finishing off' the cap which had already suffered long term damage from overheating. Again, sorry if you thought I was being arsey with you, me old mate. I really wasn't. :-) Arfa |
#16
Posted to sci.electronics.repair
|
|||
|
|||
Fuse Failure Machanism ...??
On Wed, 9 Sep 2009 09:37:54 +0100, "Arfa Daily" wrote:
: :"Ross Herbert" wrote in message .. . : On Tue, 8 Sep 2009 09:48:47 +0100, "Arfa Daily" : wrote: : : : : :"Ross Herbert" wrote in message : .. . : SNIP : : : : : I would be more concerned with what caused the filter cap to bulge... : : : : If it is a well known brand and correctly rated for the application : then : : it : : should not have degenerated to that state as long as normal input : voltage : : range : : was experienced. I also doubt that a possible short term lightning : event : : would : : have caused the cap to bulge - this symptom is more likely due to a : longer : : term : : overvoltage event. : : : : If all the major input circuitry and components are ok I would suspect : a : : leaky : : diode in the bridge rectifier. : : : :Presumably, you don't see too many small high current switchers ? : : Not in the last few months. No. However I was repairing small and large : SMPS : quite frequently in the past. The symptoms you described are exactly the : same as : I found in small 5" x 3" format SMPS I recently repaired, although there : was : only one series fuse and a current inrush limiter - both of which had : died. The : main filter cap was also bulging, as in your case, and the fault was : traced to a : dud diode in the bridge rectifier. The suggestion was made as a : possibility : since I can't actually see the unit myself and all particulars were not : disclosed initially. : : :This is a : :small supply - probably around 6" x 3" x 1.5", and fully enclosed in a : lastic case. The cap in question was a CapXon 120uF at 450v, and a 105 : deg : :type, so a common enough make, more than adequately rated for the job. As : is : :ever the case, it is the way that the designer has used it, that has led : to : :its demise. It was layed over flat on the board, jammed in by the : heatsink : :that carries the secondary side reccies etc. This is a very typical : :scenario, which anyone who works with them a lot, will tell you leads to : :drying out, bulging, and ultimate failure. : : The fully enclosed nature of your unit does help to explain a possible : reason : for long term heating as a possible cause for the cap bulging. Pity you : didn't : include those details before since it is well known that heat is a major : killer : of caps in SMPS. : : :Sorry Ross - wasn't getting at you. When I said "presumably you don't see :...etc" I was being quite genuine in asking. Although I didn't specifically :say that it was a fully enclosed type, I did say in the original post that :it was "...a small external switcher from an LCD TV." I assumed that anyone :who was regularly involved in the repair of such items, would immediately :recognise that description as being a small, plastic, fully enclosed type. :Interesting that you had identical symptoms on a similar one, and that you :actually found a leaky diode in the bridge. Can you from memory, put a value n the amount of leakage ? I figure it must have been quite small, as any :leaky bridges I've had, have had a much more catastrophic effect than just ver-working the main filter cap for long enough to dry it out. I was riginally thinking U.S. 110v input and whether the reduced voltage might :allow such a leak to fester away without exploding anything, but thinking :about it some more, you're in Aus-land aren't you ? Line voltage nominally :230 - ish same as here in the U.K. ?? That's OK Arfa.. words alone don't convey facial expressions unfortunately. I have certainly been guilty of unintentionally upsetting people with terse remarks on the NG's :-) Actually, when the SMPS came to me the diode had actually gone fully short circuit. I guessed that if it had catastrophically failed in one hit the probable result would have been that the fuse and inrush limiter would have failed rapidly and the cap would not have been overheated long enough to cause bulging. I reasoned that the diode had started failing (become leaky) which gradually applied overvoltage and incorrect polarity pulses to the cap which caused it to overheat and begin bulging. Only when the diode had gone almost short did it cause the fuse and inrush limiter to rupture but by then the cap had also ad enough and it was not in good shape either. Our mains voltage, while nominally quoted as 230V, actually sits around 255V in most cases so components in SMPS here are stressed quite a bit. : : : : : : :I'm not sure where you got it from that a lightning event was thought to : be : :responsible for this bulging, Ross. I don't think I actually said that. : : The lightning suggestion was offered by in his : response and : that is what I was referring to. : :Ah, OK. I misunderstood you. I thought that you thought that I thought ( :!!! ) that the lightning had led to the bulging. I was actually not :associating the bulging with any lightning event, but considering the ossibility that a surge on the line voltage from a nearby strike, as :suggested by the poster that you cite, might have been responsible for the :failure of the fuses, and for possibly 'finishing off' the cap which had :already suffered long term damage from overheating. Yes, it is possible that this sequence of events could have occurred. I mistakenly assumed that given all operational conditions were normal, and based on my experience, the cap would be in good order and not already bulging. I reasoned that if an induced lightning splat did occur, it might blow the fuses but it is unlikely it would have caused the bulging cap at that time. I failed to take into account that since you hadn't seen the unit until after it had completely failed you couldn't have known what sequence of events had transpired. The cap may have been already bulging due to its normal operating environment before the fatal over-current (whatever the cause) blew the fuses. I sincerely apologise for this inexcusable oversight. In most cases in my experience it is rare for failure of the main filter cap/s following the bridge in universal SMPS to occur, since they are usually well selected types for the application and physically large enough to dissipate any heat generated in their vicinity. I think I can truthfully say that I have had to change only about 2 such capacitors out of the several hundred small SMPS I have repaired. In most cases the Tan-Delta of the insitu caps have exhibited extremely low values even though they have already seen many years of service. It is also not unreasonable that the cap in your unit is not as good as it should be and this has lead to excessive heating and subsequent bulging. I am sure that you would now have checked the individual diodes in the bridge rectifier with your DVM and found them to be ok, hence your question on "how much leakage" did I find in my case. In my case there was a shorted diode and I reasoned it hadn't failed short circuit suddenly but had caused the bulging cap over a period of time before finally failing S/C and taking out the fuse and inrush limiter. I don't know if there was any lightning event at the time the unit actually failed, but while this is also a possibility, I doubt that it would have been the real cause of the failure. If all your diodes test ok on the DVM I don't think anyone can know for certain what the failure mechanism was in this case. And since testing for diode leakage over the full working voltage range is not all that easy I can only suggest that you change the bridge rectifier (or all individual diodes in the bridge) just to be on the safe side. : :Again, sorry if you thought I was being arsey with you, me old mate. I :really wasn't. :-) : :Arfa : : : No problem Arfa... |
#17
Posted to sci.electronics.repair
|
|||
|
|||
Fuse Failure Machanism ...??
: :Again, sorry if you thought I was being arsey with you, me old mate. I :really wasn't. :-) : :Arfa : : : No problem Arfa... We are pretty much on the same page with this I think d;~} Arfa |
#18
Posted to sci.electronics.repair
|
|||
|
|||
Fuse Failure Machanism ...??
Bob Larter wrote: Tony Matt wrote: N_Cook wrote: If anyone knows the USA term I will add to my translator http://www.divdev.fsnet.co.uk/tool_terms.htm I don't know of a standard term, but browsing through DigiKey datasheets, the terms 'subminiature', 'micro', 'cartridge', and 'IEC 60127-3' are commonly used. Littlefuse/Wickmann: http://www.littelfuse.com/data/en/Da..._LF_011906.pdf Littlefuse: http://media.digikey.com/pdf/Data%20.../663SERIES.pdf Belfuse: http://www.belfuse.com/Data/Datasheets/MRT.pdf Cooper/Bussmann: http://www.cooperbussmann.com/pdf/12...75cdc90d96.pdf Schurter: http://www.schurterinc.com/pdf/english/typ_mst_250.pdf I've seen similar fuses on PCI extender/debug cards. They sound like the fuses that used to be common on SCSI cards. They look very much like small value electrolytics, except hard plastic cases, with the value on the top, rather than on the side. That sounds like a 'Picofuse'. -- You can't have a sense of humor, if you have no sense! |
#19
Posted to sci.electronics.repair
|
|||
|
|||
Fuse Failure Machanism ...??
Bob Larter wrote:
As soon as the cap and three fuses were replaced, operation of the supply was normal, and it powered the TV without issue. Thoughts anyone ? Arfa If you were here in the US midwest, I would say it was a nearby lightning strike and the fuses kept arcing after the first one opened. That'd be my guess too. A nearby ground-strike will arc over a zapped fuse with no trouble at all. War of the Worlds. The aliens are ready to rise. -- Adrian C |
#20
Posted to sci.electronics.repair
|
|||
|
|||
Fuse Failure Machanism ...??
"Michael A. Terrell" wrote in message m... Bob Larter wrote: Tony Matt wrote: N_Cook wrote: If anyone knows the USA term I will add to my translator http://www.divdev.fsnet.co.uk/tool_terms.htm I don't know of a standard term, but browsing through DigiKey datasheets, the terms 'subminiature', 'micro', 'cartridge', and 'IEC 60127-3' are commonly used. Littlefuse/Wickmann: http://www.littelfuse.com/data/en/Da..._LF_011906.pdf Littlefuse: http://media.digikey.com/pdf/Data%20.../663SERIES.pdf Belfuse: http://www.belfuse.com/Data/Datasheets/MRT.pdf Cooper/Bussmann: http://www.cooperbussmann.com/pdf/12...75cdc90d96.pdf Schurter: http://www.schurterinc.com/pdf/english/typ_mst_250.pdf I've seen similar fuses on PCI extender/debug cards. They sound like the fuses that used to be common on SCSI cards. They look very much like small value electrolytics, except hard plastic cases, with the value on the top, rather than on the side. That sounds like a 'Picofuse'. I've always known picofuses to be of axially leaded cylindrical construction, looking like a small moulded choke package. Very confusing how terms vary from place to place around the world ... I should be in your neck of the woods in a few weeks Michael. Arfa |
#21
Posted to sci.electronics.repair
|
|||
|
|||
Fuse Failure Machanism ...??
N_Cook wrote:
Tony Matt wrote in message ... [...] Littlefuse/Wickmann: http://www.littelfuse.com/data/en/Da..._LF_011906.pdf [...] incidently ( Littelfuse & Wickman spellings) Yes, I missed the Littelfuse spelling (but not in the Hot Wheels thread); you might want to recheck the spec re Wickmann. TM |
#22
Posted to sci.electronics.repair
|
|||
|
|||
Fuse Failure Machanism ...??
Arfa Daily wrote: "Michael A. Terrell" wrote in message m... Bob Larter wrote: Tony Matt wrote: N_Cook wrote: If anyone knows the USA term I will add to my translator http://www.divdev.fsnet.co.uk/tool_terms.htm I don't know of a standard term, but browsing through DigiKey datasheets, the terms 'subminiature', 'micro', 'cartridge', and 'IEC 60127-3' are commonly used. Littlefuse/Wickmann: http://www.littelfuse.com/data/en/Da..._LF_011906.pdf Littlefuse: http://media.digikey.com/pdf/Data%20.../663SERIES.pdf Belfuse: http://www.belfuse.com/Data/Datasheets/MRT.pdf Cooper/Bussmann: http://www.cooperbussmann.com/pdf/12...75cdc90d96.pdf Schurter: http://www.schurterinc.com/pdf/english/typ_mst_250.pdf I've seen similar fuses on PCI extender/debug cards. They sound like the fuses that used to be common on SCSI cards. They look very much like small value electrolytics, except hard plastic cases, with the value on the top, rather than on the side. That sounds like a 'Picofuse'. I've always known picofuses to be of axially leaded cylindrical construction, looking like a small moulded choke package. Very confusing how terms vary from place to place around the world ... There are axial types that solder in, and a bi-pin version that plugs in. Picofuse was the company name. The first I saw were in Jerrold CATV trunk amplifiers in 1972. They were a pain in the ass. You are on a ladder or in a bucket truck, trying to remove the ceramic screw on cover, and pull the fuse without losing either part. http://us.100y.com.tw/US-Catalog-pdf/18-02.pdf type tr5 at the bottom of the page is a similar version. I should be in your neck of the woods in a few weeks Michael. Let me know if you want to stop by. I may be in Apopka, which is over half way to Orlando to pick up some donated equipment. -- You can't have a sense of humor, if you have no sense! |
#23
Posted to sci.electronics.repair
|
|||
|
|||
Fuse Failure Machanism ...??
bucket truck = what we ,limies, call a cherry picker?
|
#24
Posted to sci.electronics.repair
|
|||
|
|||
Fuse Failure Machanism ...??
bucket truck = What we Limies call a cherry picker?
It's called the same thing in the US. I've never heard it called a bucket truck. |
#25
Posted to sci.electronics.repair
|
|||
|
|||
Fuse Failure Machanism ...??
William Sommerwerck wrote in message
... bucket truck = What we Limies call a cherry picker? It's called the same thing in the US. I've never heard it called a bucket truck. perhaps its a Mason-Dixon deliniation thing |
#26
Posted to sci.electronics.repair
|
|||
|
|||
Fuse Failure Machanism ...??
N_Cook wrote: bucket truck = what we ,limies, call a cherry picker? A cherry picker is a similar, but lighter and small vehicle used for picking fruit. A bucket truck is too heavy and too wide to go down the rows in most groves. A bucket truck usually has outriggers to stabilize them when used off asphalt on concrete roads. -- You can't have a sense of humor, if you have no sense! |
#27
Posted to sci.electronics.repair
|
|||
|
|||
Fuse Failure Machanism ...??
N_Cook wrote: William Sommerwerck wrote in message ... bucket truck = What we Limies call a cherry picker? It's called the same thing in the US. I've never heard it called a bucket truck. perhaps its a Mason-Dixon deliniation thing. No, its a term used by utility companies. -- You can't have a sense of humor, if you have no sense! |
#28
Posted to sci.electronics.repair
|
|||
|
|||
Fuse Failure Machanism ...??
On Sep 9, 6:28*pm, "Michael A. Terrell"
wrote: Arfa Daily wrote: "Michael A. Terrell" wrote in message om... Bob Larter wrote: Tony Matt wrote: N_Cook wrote: If anyone knows the USA term I will add to my translator http://www.divdev.fsnet.co.uk/tool_terms.htm I don't know of a standard term, but browsing through DigiKey datasheets, the terms 'subminiature', 'micro', 'cartridge', and 'IEC 60127-3' are commonly used. Littlefuse/Wickmann: http://www.littelfuse.com/data/en/Da..._LF_011906.pdf Littlefuse: http://media.digikey.com/pdf/Data%20...0PDFs/663SERIE... Belfuse: http://www.belfuse.com/Data/Datasheets/MRT.pdf Cooper/Bussmann: http://www.cooperbussmann.com/pdf/12...c3-a975cdc90d9... Schurter: http://www.schurterinc.com/pdf/english/typ_mst_250.pdf I've seen similar fuses on PCI extender/debug cards. They sound like the fuses that used to be common on SCSI cards. They look very much like small value electrolytics, except hard plastic cases, with the value on the top, rather than on the side. * That sounds like a 'Picofuse'. I've always known picofuses to be of axially leaded cylindrical construction, looking like a small moulded choke package. Very confusing how terms vary from place to place around the world ... * *There are axial types that solder in, and a bi-pin version that plugs in. *Picofuse was the company name. *The first I saw were in Jerrold CATV trunk amplifiers in 1972. *They were *a pain in the ass. *You are on a ladder or in a bucket truck, trying to remove the ceramic screw on cover, and pull the fuse without losing either part. http://us.100y.com.tw/US-Catalog-pdf/18-02.pdftype tr5 at the bottom of the page is a similar version. I should be in your neck of the woods in a few weeks Michael. * *Let me know if you want to stop by. *I may be in Apopka, which is over half way to Orlando to pick up some donated equipment. -- You can't have a sense of humor, if you have no sense! Empirical Note: That 3AG fuse style, the glass tube, 1A is perfect if you want a huge spike when the fuse blows. I tried a lot of fuse types before I settled on that one. Use four 12 Volt deep discharge vehicle batteries in series, a spool of 4/0 cabling [about 50uH], and a starter solenoid for contactor. The circuit forms a short through the fuse. When the solenoid activates you get about 300-500 A through the fuse and it goes off like a flash bulb. The fuse stops conducting abruptly enough that the inductance gives you an excellent kick back to meet BT's weird telecom -48V power surge spec. I couldn't get any other fuse type to do as well. Robert |
#29
Posted to sci.electronics.repair
|
|||
|
|||
Fuse Failure Machanism ...??
Robert Macy wrote: Empirical Note: That 3AG fuse style, the glass tube, 1A is perfect if you want a huge spike when the fuse blows. I tried a lot of fuse types before I settled on that one. Use four 12 Volt deep discharge vehicle batteries in series, a spool of 4/0 cabling [about 50uH], and a starter solenoid for contactor. The circuit forms a short through the fuse. When the solenoid activates you get about 300-500 A through the fuse and it goes off like a flash bulb. The fuse stops conducting abruptly enough that the inductance gives you an excellent kick back to meet BT's weird telecom -48V power surge spec. I couldn't get any other fuse type to do as well. Any time you generate plasma in a fuse, it will do that. You should see the damage when some idiot uses the old SFE 32 volt automotive fuses in a 120 or higher application. Did you try AGC series fuses? -- You can't have a sense of humor, if you have no sense! |
#30
Posted to sci.electronics.repair
|
|||
|
|||
Fuse Failure Machanism ...??
On Sep 11, 10:16*am, "Michael A. Terrell"
wrote: Robert Macy wrote: Empirical Note: That 3AG fuse style, the glass tube, 1A is perfect if you want a huge spike when the fuse blows. I tried a lot of fuse types before I settled on that one. *Use four 12 Volt deep discharge vehicle batteries in series, a spool of 4/0 cabling [about 50uH], and a starter solenoid for contactor. *The circuit forms a short through the fuse. When the solenoid activates you get about 300-500 A through the fuse and it goes off like a flash bulb. *The fuse stops conducting abruptly enough that the inductance gives you an excellent kick back to meet BT's weird telecom -48V power surge spec. *I couldn't get any other fuse type to do as well. * *Any time you generate plasma in a fuse, it will do that. *You should see the damage when some idiot uses the old SFE 32 volt automotive fuses in a 120 or higher application. * *Did you try AGC series fuses? -- You can't have a sense of humor, if you have no sense! a well designed fuse will 'slowly' go away what does the AGC look like? |
#31
Posted to sci.electronics.repair
|
|||
|
|||
Fuse Failure Machanism ...??
Robert Macy wrote: Michael A. Terrell wrote: Did you try AGC series fuses? a well designed fuse will 'slowly' go away what does the AGC look like? Like a 3AG. -- You can't have a sense of humor, if you have no sense! |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
diff between a 250V 10A fuse and a 32V 10A glass fuse? | Home Repair | |||
Uninteruptable Power Source Fuse trouble shoot,fuse location etc. | Electronics Repair | |||
Uninteruptable Power Source Fuse trouble shoot,fuse location etc. | Electronics Repair | |||
Uninteruptable Power Source Fuse trouble shoot,fuse location etc. | Electronics Repair | |||
plug ring circuit keeps flicking the fuse switch on fuse board | UK diy |