Electronics Repair (sci.electronics.repair) Discussion of repairing electronic equipment. Topics include requests for assistance, where to obtain servicing information and parts, techniques for diagnosis and repair, and annecdotes about success, failures and problems.

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
  #1   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 1
Default PA speaker repair


I have a Kustom PA speaker that can handle up to 80 watts. A 120 Watt
guitar head was plugged into it and now all that comes out of it is a
faint crackled signal. I can tell what I'm playing when I play trough
it but it is just very quiet and distorted. What have I blown and how
can I fix it if it even can be fixed.




--
ChChChad
  #2   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 533
Default PA speaker repair

ChChChad wrote:
I have a Kustom PA speaker that can handle up to 80 watts. A 120 Watt
guitar head was plugged into it and now all that comes out of it is a
faint crackled signal. I can tell what I'm playing when I play trough
it but it is just very quiet and distorted. What have I blown and how
can I fix it if it even can be fixed.




Time to shut off the amp and plug another speaker in. Hopefully 'all'
you've blown is that Kustom. Keep playing and you'll likely blow the
amp as well.

jak
  #3   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 43,017
Default PA speaker repair

In article ,
ChChChad wrote:
A 120 Watt guitar head


What's that?

--
*What boots up must come down *

Dave Plowman London SW
To e-mail, change noise into sound.
  #4   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 6,772
Default PA speaker repair


"Dave Plowman (News)" wrote in message
...
In article ,
ChChChad wrote:
A 120 Watt guitar head


What's that?


A 120 watt head dimensioned for lead guitar ? That's what I tend to call
them as well, Dave. As opposed to a 'combo' or 'slave' or 'bass head' ??

As far as the OP's problem goes, it is likely that the voice coil has
overheated and boiled the insulation on the wire making up that winding.
This causes it to 'bubble up' and effectively increase its cross section,
which in turn causes it to fill up the tiny air gap that it runs in, making
it foul the magnet pole pieces and drag or totally seize, as it sounds like
has happened in this case.

Speakers can be re-coned by specialist repairers, but unless you are
particularly 'in love' with the sound this specific speaker makes, you may
as well just scrap and replace it. Replacement drivers for this market are
surprisingly cheap, and you will almost certainly find that your local PA
equipment store carries such replcements 'on the shelf'. I agree with jak
that if you keep trying to use it, you are likely to fry the driving amp as
well.

Arfa
--
*What boots up must come down *

Dave Plowman London SW
To e-mail, change noise into sound.



Reply
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules

Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
Speaker [email protected] Electronics Repair 8 September 21st 07 11:18 AM
Cheapie 2.1 Speaker Set with static in left speaker Peale Electronics Repair 8 May 31st 07 09:17 AM
PC speaker hum Eeyore Electronics Repair 3 September 17th 06 12:17 PM
speaker box assignment [email protected] Electronics Repair 14 November 6th 05 03:19 AM
Looking for US/Canada source for mylar film for electrostatic speaker repair William Buchholz Electronics Repair 2 May 25th 05 06:53 AM


All times are GMT +1. The time now is 06:33 PM.

Powered by vBulletin® Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Copyright ©2004-2025 DIYbanter.
The comments are property of their posters.
 

About Us

"It's about DIY & home improvement"