Electronics Repair (sci.electronics.repair) Discussion of repairing electronic equipment. Topics include requests for assistance, where to obtain servicing information and parts, techniques for diagnosis and repair, and annecdotes about success, failures and problems.

Reply
 
LinkBack Thread Tools Search this Thread Display Modes
  #1   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 15
Default TEDELEX SERVICE MENU

74CM Colour Television
Chassis EC2975
or TCB00892
or 40-2916-MT-MA


Hi
Tube had a green gun that had died. (Heating up the Filaments, and then
firing 240v through a 50w bulb between G1 and GK, managed to give me about
10 minutes before the green died again).

Replaced with another tube of same size (Using the same Yolk that is on the
replacement tube [I did read the faq])

My Picture is focused at the center, but at the edges it starts to get
blurry, and I can see that it is overrunning the screen border by at least
10cm on each side.
My guess is that this is beacuse of the different yolk impedance.
Anybody know how to correct this (resistors in parralel / series with the
Yolk maybe),

I would also like (for interest sake) to know how to access this sets
service menu [if somebody could please help].

BTW I am doing this one as a hobby, as I would like to get a TV going for my
lounge [and i was given this tv with a bad tube]

Thanks
Peter


  #2   Report Post  
Posted to sci.electronics.repair
external usenet poster
 
Posts: 15
Default TEDELEX SERVICE MENU

Just an update.
Got the Service Manual from Local dealer.

Easily managed to adjust settings (in service menu) to get picture working
fine with the other tube.

Was actually surprised that the set gave me such a wide range to bring the
Vertical and Horizontal Amplitudes down.

Peter

"Peter Kolbe" wrote in message
...
74CM Colour Television
Chassis EC2975
or TCB00892
or 40-2916-MT-MA


Hi
Tube had a green gun that had died. (Heating up the Filaments, and then
firing 240v through a 50w bulb between G1 and GK, managed to give me about
10 minutes before the green died again).

Replaced with another tube of same size (Using the same Yolk that is on
the replacement tube [I did read the faq])

My Picture is focused at the center, but at the edges it starts to get
blurry, and I can see that it is overrunning the screen border by at least
10cm on each side.
My guess is that this is beacuse of the different yolk impedance.
Anybody know how to correct this (resistors in parralel / series with the
Yolk maybe),

I would also like (for interest sake) to know how to access this sets
service menu [if somebody could please help].

BTW I am doing this one as a hobby, as I would like to get a TV going for
my lounge [and i was given this tv with a bad tube]

Thanks
Peter





Reply
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules

Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


Similar Threads
Thread Thread Starter Forum Replies Last Post
RCA service menu. Dani Electronics Repair 1 February 21st 07 09:32 PM
RCA service menu. Dani Electronics Repair 1 February 6th 07 12:50 AM
TV service menu [email protected] Electronics Repair 2 June 30th 06 05:26 AM
RCA CRT TV Service Menu [email protected] Electronics Repair 4 February 24th 06 05:09 PM
Apex tv service menu? Arthur Jernberg Electronics Repair 2 July 17th 03 03:50 AM


All times are GMT +1. The time now is 01:27 AM.

Powered by vBulletin® Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright ©2004-2024 DIYbanter.
The comments are property of their posters.
 

About Us

"It's about DIY & home improvement"