Home |
Search |
Today's Posts |
|
Electronics Repair (sci.electronics.repair) Discussion of repairing electronic equipment. Topics include requests for assistance, where to obtain servicing information and parts, techniques for diagnosis and repair, and annecdotes about success, failures and problems. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
#1
Posted to sci.electronics.repair
|
|||
|
|||
Multimeter Meterman 37X repair
Hello
Any person knows where I can find the electrical schematic of the multimeter Meterman 37XR, or any information? Maybe the serie 30xr, 33xr, 34xr, 38xr they will be seemed It is for to attempt to repair it. I connected it to more than 1000v, (it was not knowing that there was more than 1000v) and now indicates low impedance between the test leads, 2.400 ohms. I know maybe the failure is only in the input stage. Any information will be welcomed Regards Quim |
#2
Posted to sci.electronics.repair
|
|||
|
|||
Multimeter Meterman 37X repair
Quim wrote:
Hello Any person knows where I can find the electrical schematic of the multimeter Meterman 37XR, or any information? Maybe the serie 30xr, 33xr, 34xr, 38xr they will be seemed It is for to attempt to repair it. I connected it to more than 1000v, (it was not knowing that there was more than 1000v) and now indicates low impedance between the test leads, 2.400 ohms. I know maybe the failure is only in the input stage. The low resistance across the test leads may indicate that there is a protection diode or two across the probes, which have failed to a short circuit. Ron(UK) |
#3
Posted to sci.electronics.repair
|
|||
|
|||
Multimeter Meterman 37X repair
Hello
The low resistance is 2,4Kohms, yes, maybe it is a diodes or a resistors, but have a lot, and they are SMD, but there is not a "short short" circuit, when I place the rotary swich at Ohms, the display indicate 2,4Kohms, and in the others: Volt, Capacitance, etc. the display shows a value altered when I attempt to test a voltage, capacitance, etc. All the ranges are protected but this metter not have a protection for over than 1000v. "Ron(UK)" escribió en el mensaje ... Quim wrote: Hello Any person knows where I can find the electrical schematic of the multimeter Meterman 37XR, or any information? Maybe the serie 30xr, 33xr, 34xr, 38xr they will be seemed It is for to attempt to repair it. I connected it to more than 1000v, (it was not knowing that there was more than 1000v) and now indicates low impedance between the test leads, 2.400 ohms. I know maybe the failure is only in the input stage. The low resistance across the test leads may indicate that there is a protection diode or two across the probes, which have failed to a short circuit. Ron(UK) |
#4
Posted to sci.electronics.repair
|
|||
|
|||
Multimeter Meterman 37X repair
Quim wrote:
Hello The low resistance is 2,4Kohms, yes, maybe it is a diodes or a resistors, but have a lot, and they are SMD, but there is not a "short short" circuit, when I place the rotary swich at Ohms, the display indicate 2,4Kohms, and in the others: Volt, Capacitance, etc. the display shows a value altered when I attempt to test a voltage, capacitance, etc. All the ranges are protected but this metter not have a protection for over than 1000v. Ah I read it as 2.400 ohms, any road up, that`s where I would start looking. Ron(UK) |
#5
Posted to sci.electronics.repair
|
|||
|
|||
Multimeter Meterman 37X repair
"Quim" wrote in message ... Any person knows where I can find the electrical schematic of the multimeter Meterman 37XR, or any information? Maybe the serie 30xr, 33xr, 34xr, 38xr they will be seemed http://www.elexp.com/tst_38xr.htm ??? -- .. .. .. .. .. .. .. .. |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
Multimeter | UK diy | |||
Multimeter | UK diy | |||
Multimeter | UK diy | |||
multimeter | Home Repair | |||
Another multimeter Q | Electronics Repair |