Home |
Search |
Today's Posts |
|
Electronics Repair (sci.electronics.repair) Discussion of repairing electronic equipment. Topics include requests for assistance, where to obtain servicing information and parts, techniques for diagnosis and repair, and annecdotes about success, failures and problems. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
#1
|
|||
|
|||
FLASH, CPLD, FPGA - Future of repair?
Hi together,
looking at modern products repairing them becomes increasingly difficult. Due to the massive use of programmable logic and software residing in flash memory - there are lots of componentes which can not be checked or replaced - even if they are known to be defective... Sometimes even the original manufacturer is not able to supply the right chips to fix the problem. My question is how the know how residing in such chips can be saved prior to their death? For software there exists an archiv (bitsaver.org) to preserve it, but how e.g. on fuse-lists of FPGAs? Logic devices are hard to read out without the appropriate programmer. Even if they are in a socket the protection fuse my prevent reading... Is there any experience how long EEPROM-based FPGAs and CPLDs really keep their programming? The actual reason for my fear of these components is that test equipemt, especially high quality one like tektronix or agilent, always was an investment for many years - who is not happy about his working Tek535 on a cold winter day? Recently there came up relatively many of high end oscilloscopes (545xx) on eBay with comments like "out of service", "agilent refused to repair", "not serviceable". Since I own such a device, I suspect the ALTERA EPM5128 or the soldered in flash memory beeing the problem. Honestly speaking I was shocked that HP/agilent oscilloscopes are "not servicable" only a couple of years after they have been discontiuned :-( Thanks god, my 54542a still works... Erik. |
#2
|
|||
|
|||
The actual reason for my fear of these components is that test equipemt, especially high quality one like tektronix or agilent, always was an investment for many years - who is not happy about his working Tek535 on a cold winter day? Recently there came up relatively many of high end oscilloscopes (545xx) on eBay with comments like "out of service", "agilent refused to repair", "not serviceable". Since I own such a device, I suspect the ALTERA EPM5128 or the soldered in flash memory beeing the problem. Honestly speaking I was shocked that HP/agilent oscilloscopes are "not servicable" only a couple of years after they have been discontiuned :-( Thanks god, my 54542a still works... This has been a problem for quite a while now, a number of very good Tek scopes for example use custom IC's that run hot and are unobtainable. |
#4
|
|||
|
|||
James Sweet wrote:
Honestly speaking I was shocked that HP/agilent oscilloscopes are "not servicable" only a couple of years after they have been discontiuned :-( Thanks god, my 54542a still works... This has been a problem for quite a while now, a number of very good Tek scopes for example use custom IC's that run hot and are unobtainable. OK, this is an interesting note - but if one does not use the instrument regularly it should last a long time. And knowing about this problem one could implement better cooling by e.g. a small fan. With EPROM and FLASH its worse: The charge on the floating gate degrades and renders the device useless independent of using it or not :-( Which Tek's are likely to encounter this problem? Thanks, Erik. |
#5
|
|||
|
|||
"Dr. Anton T. Squeegee" wrote:
What you describe, Erik, is unfortunately an all-too-common problem in today's electronics world, and it is one of the major reasons why there is such a thriving market for used (and older) equipment. Obviously - but the replacements obtained from other equipment are old, too. I think they will last several years but not 10 years until they "forget" the data programmed in, right? One of the biggest problems I see is that, about 20 or so years ago, a distressing trend began where much of the electronics industry (heck, much of the PLANET for that matter!) stopped being interested in long-term gains and (in the case of the electronics industry) longevity of products. They began to favor, instead, short-term profit over long- term growth. YES - you are ABSOLUTELY RIGHT! Looking at HPs way is a interesting example, too. not long ago, saying that they wanted to try and greatly expand HP's downloadable offerings on manuals and service information for older equipment. Hey, that would be a great thing. From a developers point of view it would be very good to know that the own work invested in the firmware of e.g. an oscilloscope is preserved for the future. But honestly speaking I doubt that e.g. the firmware of an oscilloscope will be released for download?? How far this attempt will go is anyone's guess, but at least one person is trying. Perhaps, in time, there will be others. One person my do a lot. E.g. I am fan of SGI computers and this company had in the past some guys supporting freeware on SGI systems - lot of this work was done in their free time. They were really helpful regarding internals and it was a pleasure to contact them! equipment, and learn well! Such skills could really save your tail (and a whole ton of $$ if you shop carefully). I know. I've built my entire lab using such techniques. ;-) In the past I had good contact to the electronics waste container at Munich's university and most of my lab consists of repaired equipment therefrom. But today I bought buy some items on eBay... Thanks for your tips, Erik. |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
LeCroy Oscilloscope/ VME/ CAMAC/ NIM/ FASTBUS repair | Electronics Repair | |||
GE refrigerator warranty repair misery | Home Ownership | |||
Olympus D-460Z Flash repair? | Electronics Repair | |||
Remote Sensor for Underwater Flash Strobe | Electronics Repair | |||
How to repair an UFO? | Electronics Repair |