View Single Post
  #3   Report Post  
Steve Knight
 
Posts: n/a
Default

30% Off planes of all sorts.
all bench planes and panel raisers have adjustable sliding mouths. no more
mouthblocks (unless you want one)
prices will be rasing soon so get the planes while they are hot.
The Plow plane is finished. It is a simple setup with 6 standard blades. ¼”
3/16” 5/16” ½” 5/8” and 3/4” and ¼” thick. The steel sole is 7/64” thick O-1
steel it is screwed and glued into the body. The plane is about 10” long and
about 4” high the fence can be used on both sides of the plane. The regular
price right now is 250.00 the irons rest against one side of the plane to make
setup easy and measurements of where the dado starts a simple ipe block works
for the depthstop.
http://www.knight-toolworks.com/web_...plowplane1.jpg
http://www.knight-toolworks.com/web_...plowplane2.jpg


New marking knives and hammers are now available.
http://www.knight-toolworks.com/web_.../newknives.jpg
made by CHESTER TOOLWORKS LLC and they are made from precision ground 3/32"
thick O1 tool steel and are 5/16" wide. Snakewood, East Indian Rosewood,
Brazilian Tulipwood, or Gabon Ebony. 44.00 for the snakewood and shipping 39.00
and shipping for the other woods.
New plane adjusting hammer
http://www.knight-toolworks.com/web_.../newhammer.jpg CTW hammers are
designed specifically for adjusting the blades and wedges of wooden hand planes
and infill hand planes. The polished brass and Lignum Vitae head is weighted
toward the brass striking end and is designed so that it won't mar or mushroom
the blade like steel hammers. The Lignum end is of a smaller diameter and is
used to tap the toe or heel of the plane without leaving dent marks. It should
also be the end used for tapping wedges tight since it won't damage the heel of
the wedge. Handles are individually shaped from Quartersawn White Ash with the
grain oriented to prevent the runout which weakens many other hammer handles.
45.00 plus shipping. New plane idea's


Knight Toolworks in conjunction with Harrolson at www.japanesetools.com have had
these custom made Japanese irons made for western planes. These are the first
and only hand forged/laminated Japanese irons that will fit a regular wedged
plane. They are 2" wide and 5.25" long and are a bit over ¼" thick. They will
drop into any knight Toolworks plane that uses a 2" iron with just a little
mouth and wedge adjustment. They are made from blue steel (holds and edge longer
then pretty much any tool steel on the market) and wrought iron. I believe these
to be the best irons out there over O-1 and A-2 irons. They will hold an edge
longer then A-2 they will get sharper they will leave a deeper/cleaner surface
and they make the plane easier to use. They will really help with tearout too.
They are hand stamped with Shizu Tani (tranquil valley) Shipping is 5.00
including insurance.
http://www.knight-toolworks.com/web_...ironcoffin.jpg
http://www.knight-toolworks.com/grap...gradeirons.jpg

Please check my page for all my planes www.knight-toolworks.com


I also have razee jointers and jack planes and scrubs.
http://www.knight-toolworks.com/wooden.htm
I have great looking/feeling coffin smoothers
http://www.knight-toolworks.com/graphics/coffin.jpg
All planes now have setscrews to center the irons in the body and make adjusting
the iron easy.

All planes are sanded/planed and finished with a special oil and wax finish.





--
Knight-Toolworks & Custom Planes
Custom made wooden planes at reasonable prices
See http://www.knight-toolworks.com For prices and ordering instructions.