|
|
|
|
Yep -
Email sent :-)
Gunner wrote:
On Thu, 02 Dec 2004 05:17:58 GMT, "Martin H. Eastburn"
wrote:
Gunner wrote:
On Wed, 01 Dec 2004 05:50:45 GMT, "Martin H. Eastburn"
wrote:
Gunner wrote:
On 29 Nov 2004 23:37:56 -0800, (jerry_tig2003)
wrote:
Gunner wrote in message . ..
I purchased a pound of AL435 aluminum stick welding rod a couple of
weeks ago, just to futz around with. Today I got it out and played
with it.
The stuff WORKS. Rather amazing how well it works. But damn it burns
fast.
Come back in a month, will you? The stuff works, but the rods do not
keep when the pack is open. They are very sensitive to humidity.
My pound of rod has been open for at least 3 weeks and stored on a
shelf in the middle of my back yard, during the foggy season. Seems
to as yet, not been too effected. Im going to have to figure out how
to dry all my 7018 as it appears to be a bit damp as the coating tends
to flake off.
Since I have yet to build my rod cooker/container - I put a large cookie sheet
on our propane Barbie - and turned on three sets of burners [Nice big one :-) ]
Then I regulated it to the proper temp and let it set - then added a double handful of rods.
The rods outgassed for some time - and I cooked them for an hour or so. Then
I let them cool down (still inside the Barbie) as I setup my plastic sealing machine (made for food).
I took a chunk of old coke box (thin compressed carboard) and bent a 4" wide with a 4x6 chunk.
The holder end (with the sharp end edges that one clips into the rod holder).
Grabbed a small handful (precision weight naturally) put the sharp ends in the cardboard and kept them
within it as I thrust that end down deep into a long plastic bag. Bag longer than needed for re-sealing.
Once fully in, set it up to pump down the internal air (and any added moisture) keeping the sharp ends
in the cardboard all the while. Once completed, the set is held tightly and is rigid. Store in box,
on the shelf, where you wish.
Cut the area along the seal, drag out the rods needed or as needed and reseal when completed for another day.
Stick number color power diam cook hold
7018MR E7018 Gray AC/DC+ 3/32 275 175
I cut it out of a chart I created for my sticks.
Martin
I was given an entire spool of heating element wire last week. A flat
ribbon about 3/16 in its width..I wonder if I should make a rod oven?
Gunner
The ribbon heating element wire lasts and lasts. It seems that a 2-D burn does in wire,
but can't do it on ribbons.
I have some Mil-spec heaters mounted within heat sinks that I'll build one up with. Surplus
naturally. Might try doing a temp controller to idle and not increase and increase.
Martin
Ive got a ****load of new temp controllers. Want one? They are analog
temperature holding, IRRC 220vac.
Ropex Resistron RES-102 (just ran out to the shed) Made in 9 of 92.
They are about the size of a car stereo, and indeed are 220vac
The one I have in my lap goes up to 300C according to the dial on the
meter. I think I have 6 or more of them. May be different temp
ranges.
Maybe build me a simple rod oven and Ill supply the Stuff for both of
us? I also have a couple bushel baskets of mould heaters. Most of
them are rod heaters with armored leads, but have some wavy ones that
power from both ends, etc. I dont have a clue what all is here. I wish
someone with a grasp of industrial stuff would swing in and spend a
day or so here. Perhaps the mould heaters would work as a temp
source. I dont know how hot they get. Neat packaging though..stainless
steel rods of all sizes. And I know Ive got at least 100
thermocouples of all sizes. Type Ks, whatever the hell that is.....
Geeeze..there must be 20 or more sets of industrial photo electric
units all neatly still in the boxes..dumped in the big assed Gorton
pallets piled in the back yard. Pulleys, 3000 v, cogged and timing
belts, a couple thousand pounds of bearings rusting away in a big
heap... sigh...
Gunner, who really wants his yard back.....
"I mean, when's the last time you heard of a college where the Young
Republicans staged a "Sit In" to close down the Humanities building?
On the flip side, how many sit in's were staged to close the ROTC building back in the '60's?
Liberals stage protests, do civil disobedience, etc.
Conservatives talk politely and try to work out a solution to problems
through discourse until they believe that talking won't work... they they go home and open the gun cabinets.
Pray things never get to the point where the conservatives decide that
"civil disobedience" is the next step, because that's a very short route to "voting from the rooftops"
Jeffrey Swartz, Misc.Survivalism
--
Martin Eastburn, Barbara Eastburn
@ home at Lion's Lair with our computer
NRA LOH, NRA Life
NRA Second Amendment Task Force Charter Founder
|