harry Wrote in message:
On Friday, 9 September 2016 16:35:50 UTC+1, jim wrote:
The Natural Philosopher Wrote in message:
On 09/09/16 14:10, jim wrote:
The Natural Philosopher Wrote in message:
On 09/09/16 07:40, jim wrote:
The Natural Philosopher Wrote in message:
On 08/09/16 22:29, jim wrote:
The Natural Philosopher Wrote in message:
On 08/09/16 21:30, jim wrote:
The Natural Philosopher Wrote in message:
On 08/09/16 21:13, jim wrote:
Davey Wrote in message:
On Thu, 8 Sep 2016 11:26:31 -0700 (PDT)
harry wrote:

On Tuesday, 6 September 2016 17:13:44 UTC+1, R D S wrote:
We are looking at woodburning stoves, around max 5kw would suffice.

The guy who is going to fit it likes Esse and I quite like this,
https://www.google.co.uk/?gws_rd=ssl#q=esse+525+stove

Cheapest I can see it for is £670 quid.

I don't want to save money buying something cheap and naff but
don't want to spend more than necessary.

So general opinions would be appreciated on stoves and prices.

You may well find the chimney/flue arrangements costs more then the
stove.

Agreed. The cost of upgrading our chimney was so much that we didn't
install the woodburner.


What did they suggest you needed?!

normally double skinned insulated stainless steel Easily a grand,
installed.

Stoves are less.

Ah the mythical insulated stainless flue liner again
...;-)

Nothing mythical about it. That's what I installed. BCO insisted.


In an existing flue?

yes.

How did you install that into an existing flue?
(You didn't is the correct answer in case you've forgotten)


Dropped it down from the chimney. Was a right bugger as there was a dogleg.

You dropped a sectional flue from the top?

Most of it. It was non trivial. The last bit we managed to connect by
over-lowering the top bit into the space just above the fireplace.




You are only allowed flexible flues for chimneys constructed IIRC before
1978.

Not read that, gorra link?


MM. That seems to have gone from the current (2010) regulations, I was
working to 2000 regulations. However the requirement for insulation on
non-condensing appliance flues exists.

http://www.topstak.co.uk/uploads/Reg...s/ADJ_2010.pdf


http://www.stovesonline.co.uk/existing-chimneys.html


"Lining existing chimneys

Flexible chimney liner may only be used to reline existing
chimneys, not for new chimneys. The chimney liner must be
suitable for the application and the manufacturer's fitting
instructions must be followed.
Chimney liner must be installed in one continuous length with no
joints within the chimney."

Your earlier link was to rigid sectional insulated flue pipe.

You sure you've not cooked your link (etc) up? Has been known ;-)


How can I cook a link up?

You cock it up and auto correct makes it cook....

Someone said the double insulated flues were a myth,. They are not and
the link showed as much

You can't fit those to existing flues though... Physically or
legally...


Whether you need them is, however a bit harder to establish.

Te requirement these days seems to be for insulation alone, and arguably
a flexi surrounded by vermiculite is OK there. And there is no
requirement to install doubles in any existing flue. That was not the
case in my 2000 regulations. Only pre 1978 flues could be relined with
flexible.

You saying the applicable bldg regs have been relaxed? That must
be a one off....

I suspect that what has happened is some lobbying, and better quality
flexibles.

Or something else entirely...
--
Jim K


----Android NewsGroup Reader----
http://usenet.sinaapp.com/

You are confusing double skinned flexible flue with rigid flue pipe sections.


Someone is....
--
Jim K


----Android NewsGroup Reader----
http://usenet.sinaapp.com/