Swingman wrote:
On 12/27/2014 10:15 AM, Greg Guarino wrote:

Well done!

Yep, I really enjoyed reading the post too. A few good lessons tucked
in there!





I did learn a good deal; techniques to use again, and pitfalls to avoid.

I asked back when the project was just a Sketchup drawing if the
design was likely to "rack" with weight on the shelves. All the
storage I've built in the past was seriously overbuilt: all 3/4" ply,
dadoes,full back screwed into every shelf, face frame. Several of you
said that this somewhat more "open" design should be plenty strong,
and it seems to be.

Also courtesy of the wRec, I learned that shaving a "flat" onto the
dowels would make the assembly easier. That was a very handy bit of
info on a project with 224 dowels.

On my own I discovered that gloppy stuff like gel stain can pose a
problem on work with lots of inside corners. Despite the fact that
the sides of this project consisted of 40 pieces 9" long, I really
should have prefinished them, or perhaps chosen a different method.

I learned how to make better mitered corners than I have ever made
before. I also learned that even my best attempt yet falls short of
perfection. On the flip-side, I have also learned that most people
(other than the builder) tend not to notice the imperfections.

Another wRec contribution was that a random orbit sander can be used
to sand face-frame-style joints flush, followed perhaps by a finish
sander with finer grits, avoiding going over the line as much as
possible.

This was the first project that I paid significant attention to
grain. I don't have a jointer or a planer, and my schedule makes it
difficult to get to hardwood dealer when they are open for business.
(That's on my to-do list for the future though - take a day off and
buy better-quality wood) I did however go through the entire stock of
a local Lowe's, picking the 8 red oak 1x3s that had the straightest
grain from among the 50 or so pieces they had. Being the nice fellow
I am, I put the rest back in the rack. For the 1x2s I settled for
straight and not twisted.

I made my second attempt at pattern routing, which allows a guy with
limited tools to add a tiny bit of flair to an otherwise
straight-line sort of project. And I learned that, even though the
template had the full curve, it was better to flip the piece around
for the second "half" of the curve to avoid routing against the grain.

I think I'm *starting* to learn to apply the proper amount of glue,
the first time, rather than have to add more in the sparse areas and
remove gobs from the overdone areas. I also think I'm getting to know
when the squeeze-out is ready to be pared away.

During this project I greatly improved my Sketchup skills, which
means I can now quickly and efficiently draw things that will take me
nearly forever to actually build.

I learned that the use of an impact driver - now nearly ubiquitous
on TV and Youtube - carries with it the possibility of driving the
point of the pocket screw through the face of the second piece,
especially when you're doing the work in a contorted position and are
thus eager to finish quickly.

In a related lesson, I learned how to fill the blemish with a
matching color.

However, I also learned - at least most of the time - to call it a
day when I felt like I was getting fatigued and thus careless. There
are few advantages to being a hobbyist with limited resources, but
that's one of them: no deadline. Better to continue when I can apply
my full attention.

Continuing on that theme, I've learned that there are lots of ways to
do something; the days that come between my short bouts of work often
yield a better idea as I turn the next step around in my head. The
final glue-up and assembly of the second unit was much more efficient
than the first.

I've learned that even less-than-fine tools can be made more accurate
with some time and effort, and that the time and effort will be
rewarded with less frustration later on. But then the damn floor will
be out of whack.

The concept of jigs is now much more a part of my mindset. With so
many repetitive tasks, it was practically unavoidable. But besides
the efficiency, I feel much more confident in the results.

And maybe the most important thing I've learned when I step back and
look at this result is that a couple of years ago I'd have judged
this project as out of my reach. I'm aware that it would be pretty
rudimentary for many people here, but everyone starts somewhere. So
when I see designs that are "out of reach" now, I figure maybe - just
maybe - they won't be forever.

Thanks again to all.


Welcome to the wRec ...