DIYbanter - View Single Post - on topic for a change

benick[_2_]

wrote in message
...
On Sun, 21 Mar 2010 11:59:09 -0700 (PDT), "hr(bob) "
wrote:

On Mar 21, 1:27 pm, wrote:
On Sun, 21 Mar 2010 00:28:29 -0400, "benick"
wrote:

wrote in message
.. .
A friend's house (about 50 years old) has what I believe are original
Pella windows that need a bit of sash work. The balance mechanisms
are
aluminum or zinc and have a round hump profile - flat on both sides
and bulging out in the center. The sashes ride up and down on these
"humps" running in a channel or groove in both sides of the window.
If
I remove the sash stops from the inside will the balances come out of
the jam with the sash?

Does anyone know where I can view a picture of exactly how the
balance
connects to the sash, and what type of balance it is?

I need to remove 8 lower sashes to correct the hieght of the sash to
compensate for a botched job of cladding the outer framing and sill
so
the windows can be latched. The cladding was done by a contractor
several years ago. They were looking at getting the windows replaced
and asked my opinion - I looked at them and the sash etc is all in
good shape, just cannot go down far enough for the sash latches to
engage so I need to either cut down the top or the bottom of the
window so the sash-latches will line up again (roughly 1/4")

Instead of throwing bandaids and money at 50 year old warped and rotted
windows perhaps it's time to replace them...There are others out there
besides the "big window replacement companies" who do that..Ask
around..Word
of mouth is usually the best way to find a good contractor...Or do it
yourself , you said you have window experience...HTH..

Well, well, well - warped and rotted windows????
Not. They are in very good condition. As for window experience I
worked for 2 of the best replacement window contractors in the
Kitchener-Waterloo/Cambridge area of Ontario over a period of several
years. These windows are very salvageable and worth repairing.

Again, everyone is trying to tell me WHAT to do, not answering my
question of HOW to do it.

These windows are NOT going to be replaced. They ARE going to be
repaired. So stop wasting your keystrokes and bandwidth telling me to
replace the windows. Aint going to happen. Full stop.

ANyone out there have experience with the older style Pella windows
want to chip in with any information on what I should expect when I
pop the inner sash stops and try to remove the sash liner/balance
assemblies and lower sash?

I'll contact a knowlegeable window repair guy here in town when he
gets back to work next week (after March Break) and see what he has to
say. Just figured I'd see if anyone on-line had any experience ---
Seems not at this point.

Thanks anyway.- Hide quoted text -

- Show quoted text -

Can you grab the springs with some sort of a small wire hook and pull
them down below the windows so they will grab? you would have to have
a small strong wire that could fit betwen the window and the frame
inside the track somehow, but it can be done.

Looking at more and more information it appears they may NOT be Pella.
They are double pane, but not sealed units - and the removable pane is
on the OUTSIDE, where all the information I can find on Pella says the
removeable pane is on the INSIDE - so not sure WHAT brand they really
are - possibly Andersen or ???

My 1966 ranch's original windows were Pella and the removable pane was
indeed on the inside as was the screen...They always had major condensation
in the winter making it nearly impossibe to see out of them and they were a
major PITA to clean...I replaced them...Best money I ever spent....I really
don't think they are Anderson either....Probably some off brand...Alot of
CHEAP houses were just thrown together after WW2 with the baby and building
boom...HTH...