Brian, I will look at that and also, will measure the space under the
bottom end of my compressor. Thanks a lot. I do not mind spending $150
IF that gets me exactly what I want, which is a relatively quiet
package that is reliable and works in hot as well as in freezing
weather. (or at least does not crack from freezing, and could continue
draining later when the water thaws)
i
On 2008-06-26, Brian Lawson wrote:
On Wed, 25 Jun 2008 14:05:36 -0500, Ignoramus27719
wrote:
Hey again Iggy,
OK. The Burkert I have is about 10 years old, and mine is a Type
1078-1. Apparently there have been some minor style changes, and the
"new" one is a Type 1078-2. You can see that at:
http://www.buerkert.com/products_data/datasheets/DS1078-Standard-US-EN.pdf
and look at the PDF there. This mounts to an (as shown) solenoid
valve, like a Type 0330
http://www.buerkert.com/COM/search.php?SearchText=0330&Typensuche2=Search
If you are still interested, and you'd like to lemme know what city
you are in, I'll try to find a dealer/distributor closest to you.
Take care.
Brian Lawson.
XXXXXXXXXXXXXXXXXXXXXXXXX
On 2008-06-25, Brian Lawson wrote:
Hey Iggy,
If you decide NOT to go the economical route, then maybe you'd like
what I have.
I have a job specific device made by Burkert, consisting of a
blow-down valve with an accessory digital timer. I have mine set to
blow down for ten seconds any time power is applied to the compressor
controls, and again for 10 seconds every 6 hours that power is
applied. That is often enough that I never see any actual moisture
when it discharges.
Cost about 150 bucks.
Zero leakage, by the way.
If you are interested at that kind of money, lemme know and I'll get
the product info for you. I'm sure there is a distributor in your
area.
I think that it is the most idiot proof way of draining the tank. I
looked at their site a little, would be nice to know what model number
you have.
Other alternatives that I can get one are ones with a float, or else
one that operates off the unloaded valve.
i
Brian Lawson,
Bothwell, Ontario.
XXXXXXXXXXXXXXXXXXXXXXXXX
On Wed, 25 Jun 2008 12:35:04 -0500, Ignoramus27719
wrote:
On 2008-06-25, Ray Spinhirne wrote:
AndrewV wrote:
"Ignoramus19021" wrote in message
...
Looking for recommendations on a good compressor drain. Something that
works, does not need attention, tolerates occasional cold winter day
with garage door open, and does not make too much noise. McMaster's
4919K13 seems to fit the bill?
I don't know about the McMaster part but I 've installed several auto
drains from Harbor freight with good results, 2 of them in use for over 2
yrs w/ no problems. The cost was less then $15 as I remember. Simple to
install, they actuate off the unloader, you may want to use your own tubing
and fittings for the install.
YMMV
Second that on the fittings. The tubing and fittings supplied with the kit
blew
out and leaked on first use. Otherwise it seems to work ok but does leak a
little air all of the time.
Does not sound very encouraging. I want something that does not leak,
as I leak-proofed my tank enough so that if the outlet is closed, it
would run only once a week.
Anyway, these things need to be connected to the unloader valve,
right? My unloader tubing is copper.
--
Due to extreme spam originating from Google Groups, and their inattention
to spammers, I and many others block all articles originating
from Google Groups. If you want your postings to be seen by
more readers you will need to find a different means of
posting on Usenet.
http://improve-usenet.org/