Home |
Search |
Today's Posts |
|
Woodworking (rec.woodworking) Discussion forum covering all aspects of working with wood. All levels of expertise are encouraged to particiapte. |
Reply |
|
LinkBack | Thread Tools | Display Modes |
|
#1
|
|||
|
|||
make your own plywood?
I need some white mahogany plywood for the back of a cabinet I'm building
out of white mahogany. Well, you can't buy WM plywood. So, what if I resaw and plane some stock down to 1/8", then glue it on to a 1/8" luaun plywood? Will that work? Any problems with separation? How should I go about glueing it down on that thin stock? Can't clamp it very easily. I've heard of this being done, but I've never attempted it, until now. My back needs to be 44 inches long, so gluing up a solid panel of thin stock would be difficult. Thanks. |
#2
|
|||
|
|||
make your own plywood?
contact cement and j roller
"bob" wrote in message ... I need some white mahogany plywood for the back of a cabinet I'm building out of white mahogany. Well, you can't buy WM plywood. So, what if I resaw and plane some stock down to 1/8", then glue it on to a 1/8" luaun plywood? Will that work? Any problems with separation? How should I go about glueing it down on that thin stock? Can't clamp it very easily. I've heard of this being done, but I've never attempted it, until now. My back needs to be 44 inches long, so gluing up a solid panel of thin stock would be difficult. Thanks. |
#3
|
|||
|
|||
make your own plywood?
bob wrote:
How should I go about glueing it down on that thin stock? Can't clamp it very easily. For glue, use gravity. g When I glued two sheets of particle board together for a workbench top I laid them on the floor and put books, bricks, barbell weights and other heavy stuff on them. Still using it 4 +/- years later. -- Mark |
#4
|
|||
|
|||
make your own plywood?
Use contact cement to attach, and pay close attention to the edges, and
you won't go wrong. Read up on contact cement before using it. bob wrote: I need some white mahogany plywood for the back of a cabinet I'm building out of white mahogany. Well, you can't buy WM plywood. So, what if I resaw and plane some stock down to 1/8", then glue it on to a 1/8" luaun plywood? Will that work? Any problems with separation? How should I go about glueing it down on that thin stock? Can't clamp it very easily. I've heard of this being done, but I've never attempted it, until now. My back needs to be 44 inches long, so gluing up a solid panel of thin stock would be difficult. Thanks. |
#6
|
|||
|
|||
make your own plywood?
OK, I'll bite. What is white mahogany?
UA100 |
#7
|
|||
|
|||
make your own plywood?
It is actually "primavera", a tropical hardwood with no color, sort of like
birch. Has the same grain and other characteristics of genuine/"red" mahogany, but is slightly harder. You can stain it any color you want, including traditional "red" mahogany. I like it because it is easy to work with like mahogany, but I'm not limited to the red color characteristics of genuine mahogany. I buy this stuff by the bundle (400-600BF) for $2 BF. http://tropicalhardwoods.com/htm/tro.../primavera.htm "Unisaw A100" wrote in message ... OK, I'll bite. What is white mahogany? UA100 |
#8
|
|||
|
|||
make your own plywood?
On Sat, 17 Jul 2004 05:48:22 -0500, Unisaw A100
wrote: OK, I'll bite. What is white mahogany? Given that mahogany is firmly in the "Anything we bought from the importer, given a recognisable brand to make it sell" group, then the notion of "white" mahogany isn;t that much of a surprise. -- Smert' spamionam |
#9
|
|||
|
|||
make your own plywood?
Andy Dingley
Given that mahogany is firmly in the "Anything we bought from the importer, given a recognisable brand to make it sell" group, then the notion of "white" mahogany isn;t that much of a surprise. Something I encountered during my "brief" career in the stone business (marbles and granites). Though there it's way worse. UA100 |
#10
|
|||
|
|||
make your own plywood?
On Fri, 16 Jul 2004 21:50:32 -0500, "bob"
wrote: I need some white mahogany plywood for the back of a cabinet I'm building out of white mahogany. Well, you can't buy WM plywood. So, what if I resaw and plane some stock down to 1/8", then glue it on to a 1/8" luaun plywood? I'd look for ready-cut veneer of a suitable face timber, rather than trying to make my own, Making plywood from scratch is hard, but surface veneering ready-made ply (or MDF) is common practice and some pretty easy veneering. Do both sides equally to "balance" it, or you may get warping problems. Don't use contact cement. I'ts just about usable for small pieces (although I wouldn't) but for a large piece you'll never get it on straight before it sticks firmly into place. Use hot hide glue instead, the traditional and still the best. The "stick" behaviour as it goes on hot and chills is about the best behaviour I've yet found for veneering. I'd suggest a veneer hammer, rather than a roller, but that's a personal thing. -- Smert' spamionam |
#11
|
|||
|
|||
make your own plywood?
There, it's said. Each side needs help.
You can use a fiber product for the substrate versus plywood, make for an easier job, and make contact cement a better choice. If you do ply, remember to cross the grain, and hide glue is really a better bet than contact cement there. "Andy Dingley" wrote in message ... On Fri, 16 Jul 2004 21:50:32 -0500, "bob" wrote: I need some white mahogany plywood for the back of a cabinet I'm building out of white mahogany. Well, you can't buy WM plywood. So, what if I resaw and plane some stock down to 1/8", then glue it on to a 1/8" luaun plywood? I'd look for ready-cut veneer of a suitable face timber, rather than trying to make my own, Making plywood from scratch is hard, but surface veneering ready-made ply (or MDF) is common practice and some pretty easy veneering. Do both sides equally to "balance" it, or you may get warping problems. Don't use contact cement. I'ts just about usable for small pieces (although I wouldn't) but for a large piece you'll never get it on straight before it sticks firmly into place. Use hot hide glue instead, the traditional and still the best. The "stick" behaviour as it goes on hot and chills is about the best behaviour I've yet found for veneering. I'd suggest a veneer hammer, rather than a roller, but that's a personal thing. -- Smert' spamionam |
#12
|
|||
|
|||
make your own plywood?
On Fri, 16 Jul 2004 21:50:32 -0500, "bob"
wrote: I need some white mahogany plywood for the back of a cabinet I'm building out of white mahogany. Well, you can't buy WM plywood. So, what if I resaw and plane some stock down to 1/8", then glue it on to a 1/8" luaun plywood? Will that work? Any problems with separation? How should I go about glueing it down on that thin stock? Can't clamp it very easily. I've heard of this being done, but I've never attempted it, until now. My back needs to be 44 inches long, so gluing up a solid panel of thin stock would be difficult. Thanks. I have "made" ply by gluing thinner sheets together with wood glue, then used cans of paint, water-filled gallon jugs, sand bags, weights, and anything else to weigh them until the glue dried (at least 2-3 days). A vacuum clamp would probably be easier. Another approach is to use contact cement and a J-roller--no clamping with this method. |
#13
|
|||
|
|||
make your own plywood?
On Fri, 16 Jul 2004 21:50:32 -0500, "bob"
vaguely proposed a theory .......and in reply I say!: remove ns from my header address to reply via email If you're going to use contact, and have not worked with it before, practice several times until you get it right 3 X in a row, on something that does not matter, but is a large area as you are doing...... I did not follow that rule and now have a (perhaps unfair) hatred of contact. My father swears by it. I swear at it. I need some white mahogany plywood for the back of a cabinet I'm building out of white mahogany. Well, you can't buy WM plywood. So, what if I resaw and plane some stock down to 1/8", then glue it on to a 1/8" luaun plywood? Will that work? Any problems with separation? How should I go about glueing it down on that thin stock? Can't clamp it very easily. I've heard of this being done, but I've never attempted it, until now. My back needs to be 44 inches long, so gluing up a solid panel of thin stock would be difficult. Thanks. |
Reply |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Forum | |||
What is "AC fir plywood"? | Woodworking | |||
This can make you some extra cash, check it out. | Woodworking |