9mm Forstner bit in UK?
 

Anyone know where I can buy a 9mm (not 3/8") Forstner or sawtooth bit in the
UK?

9mm Forstner bit in UK?
 

On Sat, 14 Jun 2008 18:20:14 +0100, Norman Billingham wrote:

Anyone know where I can buy a 9mm (not 3/8") Forstner or sawtooth bit in
the UK?

Alright, I'll bite... why? Why does 0.525mm make such a difference
(3/8")? Why not use a 9mm centrepoint drill?

I expect you have got good reasons, I'm just curious as to what they
might be...


As an aside, for the hole you need to drill could you plunge a router
instead of using a Forstner? I know I've done that when I needed an odd
sized hole.

9mm Forstner bit in UK?
 

"Norman Billingham" norman.at.tumulus.org.uk wrote in message ...
Anyone know where I can buy a 9mm (not 3/8") Forstner or sawtooth bit in the
UK?



I'm a little surprised in the fact +0.52mm isn't accurate enough for you.

However, I wondered if you'd considered a 9mm spade bit for your task? They're more readily available, all indicators on Screwfix and Axminster led to a 3/8ths size bit, for the forstner bit. Rutlands who I consider at the top end of the British market also only do either a 3/8ths or 8 and 10mm forstner bit.

I feel you may have to compromise, or, have your own bit milled to exact specifications?

Regards
John
wheelzuk

9mm Forstner bit in UK?
 

"wheelzuk" wrote in message
...
"Norman Billingham" norman.at.tumulus.org.uk wrote in message
...
Anyone know where I can buy a 9mm (not 3/8") Forstner or sawtooth bit in
the
UK?



I'm a little surprised in the fact +0.52mm isn't accurate enough for you.

However, I wondered if you'd considered a 9mm spade bit for your task?
They're more readily available, all indicators on Screwfix and Axminster led
to a 3/8ths size bit, for the forstner bit. Rutlands who I consider at the
top end of the British market also only do either a 3/8ths or 8 and 10mm
forstner bit.

I feel you may have to compromise, or, have your own bit milled to exact
specifications?


Just curiosity mixed with perfectionism. I have some 9mm rare earth magnets
I'm using to make door catches. They fit perfectly snugly into a 9mm hole
and are loose in a 3/8" one. A 9mm brad point drill does the job nicely but
is too long to give clearance under the drill press for the edge-on wood.

There are (were) many ways out of the problem, and I did the job with a 9mm
brad point drill on a horizonal borer.

I could have shaved a bit off a 3/8" Forstner and there are other ways of
doing the job but I was surprised to find its so easy to get 3/8" and so
hard to find 9 mm in these metric days - hence the query.

Spade bits are for DIY and rough work not fine cabinet making - unless you
are prepared to do a fair bit of work on them.

9mm Forstner bit in UK?
 

Norman Billingham wrote:
"wheelzuk" wrote in message
...
"Norman Billingham" norman.at.tumulus.org.uk wrote in message
...
Anyone know where I can buy a 9mm (not 3/8") Forstner or sawtooth
bit in the
UK?



I'm a little surprised in the fact +0.52mm isn't accurate enough for
you.

However, I wondered if you'd considered a 9mm spade bit for your
task?
They're more readily available, all indicators on Screwfix and
Axminster led to a 3/8ths size bit, for the forstner bit. Rutlands
who I consider at the top end of the British market also only do
either a 3/8ths or 8 and 10mm forstner bit.

I feel you may have to compromise, or, have your own bit milled to
exact specifications?


Just curiosity mixed with perfectionism. I have some 9mm rare earth
magnets I'm using to make door catches. They fit perfectly snugly
into a 9mm hole and are loose in a 3/8" one. A 9mm brad point drill
does the job nicely but is too long to give clearance under the
drill
press for the edge-on wood.

Uh, why not just cut off a brad-point bit to the length you need? 30
seconds with a Dremel and you're done.

FWIW, googling "metric forstner bit" showed many sources for 10mm and
larger, and one set with 6mm, but no 9mm--the set jumps from 6 to 10.


There are (were) many ways out of the problem, and I did the job
with
a 9mm brad point drill on a horizonal borer.

I could have shaved a bit off a 3/8" Forstner and there are other
ways of doing the job but I was surprised to find its so easy to get
3/8" and so hard to find 9 mm in these metric days - hence the
query.

Spade bits are for DIY and rough work not fine cabinet making -
unless you are prepared to do a fair bit of work on them.

--
--
--John
to email, dial "usenet" and validate
(was jclarke at eye bee em dot net)

9mm Forstner bit in UK?
 

"J. Clarke" wrote in message
...
Norman Billingham wrote:
"wheelzuk" wrote in message
...
"Norman Billingham" norman.at.tumulus.org.uk wrote in message
...
Anyone know where I can buy a 9mm (not 3/8") Forstner or sawtooth
bit in the
UK?



I'm a little surprised in the fact +0.52mm isn't accurate enough for
you.

However, I wondered if you'd considered a 9mm spade bit for your
task?
They're more readily available, all indicators on Screwfix and
Axminster led to a 3/8ths size bit, for the forstner bit. Rutlands
who I consider at the top end of the British market also only do
either a 3/8ths or 8 and 10mm forstner bit.

I feel you may have to compromise, or, have your own bit milled to
exact specifications?


Just curiosity mixed with perfectionism. I have some 9mm rare earth
magnets I'm using to make door catches. They fit perfectly snugly
into a 9mm hole and are loose in a 3/8" one. A 9mm brad point drill
does the job nicely but is too long to give clearance under the
drill
press for the edge-on wood.

Uh, why not just cut off a brad-point bit to the length you need? 30
seconds with a Dremel and you're done.

Mainly becasue if I'd done that with the only 9mm brad point I had to hand I
would have ended up trying to grip the flutes in the chuck!


FWIW, googling "metric forstner bit" showed many sources for 10mm and
larger, and one set with 6mm, but no 9mm--the set jumps from 6 to 10.

Yes - that's what I found. Just wondered if anyone knew better.

Anyway, problem solved now

Thanks to all for comments