For those of you thinking about purchasing this planer, DON'T! I purchased
this planer in the hopes that it would be a good compromise between the 12 1/2"
planer which I have and the 15 inch planer I don't have the space for. I have
had tear out and snipe on every pass. The snipe exceeded that of my old DeWalt
12 1/2" planer in depth and length from the end of the board. On thin boards
1/8"-1/4" the board gets pulled toward the cutter head creating deep gouges in
the wood. As I was giving the yellow beast one more chance to prove itself, I
noticed that the hand wheel moves as the planer vibrates buy as much as a half
turn. That is a 32nd of an inch, enough to make fitting joints later a real
challenge. Before I am inundated with advise emails, I know all the little
tricks for getting better results. I am really disappointed with this product
from a company that I have been generally pleased with.
Brian

I've seen this planer in action and have not seen ANYTHING like you're
describing here. QUITE the opposite. I suspect your unit has a defective
head locking mechanism.

Brian.


"BRFordJr" wrote in message
...
For those of you thinking about purchasing this planer, DON'T! I
purchased
this planer in the hopes that it would be a good compromise between the 12
1/2"
planer which I have and the 15 inch planer I don't have the space for. I
have
had tear out and snipe on every pass. The snipe exceeded that of my old
DeWalt
12 1/2" planer in depth and length from the end of the board. On thin
boards
1/8"-1/4" the board gets pulled toward the cutter head creating deep
gouges in
the wood. As I was giving the yellow beast one more chance to prove
itself, I
noticed that the hand wheel moves as the planer vibrates buy as much as a
half
turn. That is a 32nd of an inch, enough to make fitting joints later a
real
challenge. Before I am inundated with advise emails, I know all the little
tricks for getting better results. I am really disappointed with this
product
from a company that I have been generally pleased with.
Brian

BRFordJr wrote:

snipped

As I was giving the yellow beast one more chance to prove itself, I
noticed that the hand wheel moves as the planer vibrates buy as much as a half
turn. That is a 32nd of an inch, enough to make fitting joints later a real
challenge.

The cutter head's depth changes with the head locked?

--
Jack Novak
Buffalo, NY - USA
(Remove "SPAM" from email address to reply)

I have this planer and it's been great. This is the first bad review I've
seen for the 735 - it's gotten nothing but praise. I think you have a
defective machine. Go and exchange it and give us an update.

"BRFordJr" wrote in message
...
For those of you thinking about purchasing this planer, DON'T! I
purchased
this planer in the hopes that it would be a good compromise between the 12
1/2"
planer which I have and the 15 inch planer I don't have the space for. I
have
had tear out and snipe on every pass. The snipe exceeded that of my old
DeWalt
12 1/2" planer in depth and length from the end of the board. On thin
boards
1/8"-1/4" the board gets pulled toward the cutter head creating deep
gouges in
the wood. As I was giving the yellow beast one more chance to prove
itself, I
noticed that the hand wheel moves as the planer vibrates buy as much as a
half
turn. That is a 32nd of an inch, enough to make fitting joints later a
real
challenge. Before I am inundated with advise emails, I know all the little
tricks for getting better results. I am really disappointed with this
product
from a company that I have been generally pleased with.
Brian

Brian,

While I don't doubt what you've written about your 735, mine has performed
nothing like the one described in the subject review. I've never
experienced any snipe to speak of, nor does my planer vibrate or move out of
adjustment while operating. The handwheel, while easy to rotated, remains
as adjusted until one turns it by hand.

I would suggest that you return it for another or have it repaired under
warranty. I am no expert on planers (of any size), but I am most impressed
at how mine makes rough boards smooth and flat. For example, to have
inexpensive wood for practicing dove-tail joinery, I recently ran a few
boards from old packing crates (remaining from my many overseas moves) and
the results were great.

Good luck on getting a replacement that works.


"BRFordJr" wrote in message
...
For those of you thinking about purchasing this planer, DON'T! I
purchased
this planer in the hopes that it would be a good compromise between the 12
1/2"
planer which I have and the 15 inch planer I don't have the space for. I
have
had tear out and snipe on every pass. The snipe exceeded that of my old
DeWalt
12 1/2" planer in depth and length from the end of the board. On thin
boards
1/8"-1/4" the board gets pulled toward the cutter head creating deep
gouges in
the wood. As I was giving the yellow beast one more chance to prove
itself, I
noticed that the hand wheel moves as the planer vibrates buy as much as a
half
turn. That is a 32nd of an inch, enough to make fitting joints later a
real
challenge. Before I am inundated with advise emails, I know all the little
tricks for getting better results. I am really disappointed with this
product
from a company that I have been generally pleased with.
Brian

For god's sakes, man RUN, don't walk back to the dealer and ask for an
exchange! I've seen that thing with my own eyes, and inspected planed
boards and there has been NO snipe at all! You've got something
seriously wrong with yours if everything that you've mentioned is true.
At the very least call tech support and see if you there is a simple
solution; otherwise get a replacement and stop whining about it.

dave

BRFordJr wrote:

For those of you thinking about purchasing this planer, DON'T! I purchased
this planer in the hopes that it would be a good compromise between the 12 1/2"
planer which I have and the 15 inch planer I don't have the space for. I have
had tear out and snipe on every pass. The snipe exceeded that of my old DeWalt
12 1/2" planer in depth and length from the end of the board. On thin boards
1/8"-1/4" the board gets pulled toward the cutter head creating deep gouges in
the wood. As I was giving the yellow beast one more chance to prove itself, I
noticed that the hand wheel moves as the planer vibrates buy as much as a half
turn. That is a 32nd of an inch, enough to make fitting joints later a real
challenge. Before I am inundated with advise emails, I know all the little
tricks for getting better results. I am really disappointed with this product
from a company that I have been generally pleased with.
Brian

On 14 Dec 2003 19:32:40 GMT, (BRFordJr) wrote:

For those of you thinking about purchasing this planer, DON'T! I purchased
this planer in the hopes that it would be a good compromise between the 12 1/2"
planer which I have and the 15 inch planer I don't have the space for. I have
had tear out and snipe on every pass.

The local store guys I talked to all said they preferred the 733 over
the 735, which is not a great way to sell them.

I had heard good things overall, except for the salespeople, until
your post. This will be interesting as more of them reach end users.

Barry

B a r r y B u r k e J r .
wrote in :

On 14 Dec 2003 19:32:40 GMT, (BRFordJr) wrote:

For those of you thinking about purchasing this planer, DON'T! I
purchased this planer in the hopes that it would be a good compromise
between the 12 1/2" planer which I have and the 15 inch planer I don't
have the space for. I have had tear out and snipe on every pass.

The local store guys I talked to all said they preferred the 733 over
the 735, which is not a great way to sell them.

I had heard good things overall, except for the salespeople, until
your post. This will be interesting as more of them reach end users.

Barry


Ever consider they may be sitting on a buttload of 733's that they somehow
have to sell with 734's and 735's becoming available?

On Mon, 15 Dec 2003 18:54:18 GMT, stickdoctorq
wrote:


Ever consider they may be sitting on a buttload of 733's that they somehow
have to sell with 734's and 735's becoming available?


The 733's have been sold out at this store for 4-5 months, but I did
consider that. This was a Woodworker's Warehouse store that stocked a
"buttload" of nothing. G

I was given the info when I inquired about the 734's three blade heads
for 733's, which I had heard was going to be offered as a retrofit.
The feeling among the employees was _why?_

Barry

indexed knives WOULD be nice, Barry! I've got the 733 and setting the
knives is time consuming.

dave

B a r r y B u r k e J r . wrote:

On Mon, 15 Dec 2003 18:54:18 GMT, stickdoctorq
wrote:


Ever consider they may be sitting on a buttload of 733's that they somehow
have to sell with 734's and 735's becoming available?



The 733's have been sold out at this store for 4-5 months, but I did
consider that. This was a Woodworker's Warehouse store that stocked a
"buttload" of nothing. G

I was given the info when I inquired about the 734's three blade heads
for 733's, which I had heard was going to be offered as a retrofit.
The feeling among the employees was _why?_

Barry

On Tue, 16 Dec 2003 01:03:32 GMT, Bay Area Dave wrote:

indexed knives WOULD be nice, Barry! I've got the 733 and setting the
knives is time consuming.


That's one reason why I was interested in a retrofit.

The four sales people stated that they unanimously thought the 733
left a better surface than the 734 and 735, due to the 733 having
higher quality, resharpenable knives, vs. the throw away knives on the
newer models.

I've never compared the two myself, and these guys had no 733's left
to sell, with both of the newer units in stock and available for sale.
It could be all baloney, but there could be something to it as well.
Only those who have used both side by side would know.

Barry

I've seen the output from a 735. It is every bit as good, if not better
than from a 733. I've got a 733 and it does a fine job, but the 735
ALSO leaves a superb finish. Don't forget, I'm that PICKY guy who has a
very low opinion of Delta 1 1/5 HP band saws. If it isn't close to
perfect, I don't like it!

dave

B a r r y B u r k e J r . wrote:

On Tue, 16 Dec 2003 01:03:32 GMT, Bay Area Dave wrote:


indexed knives WOULD be nice, Barry! I've got the 733 and setting the
knives is time consuming.



That's one reason why I was interested in a retrofit.

The four sales people stated that they unanimously thought the 733
left a better surface than the 734 and 735, due to the 733 having
higher quality, resharpenable knives, vs. the throw away knives on the
newer models.

I've never compared the two myself, and these guys had no 733's left
to sell, with both of the newer units in stock and available for sale.
It could be all baloney, but there could be something to it as well.
Only those who have used both side by side would know.

Barry