Chisels for tropical hardwoods?
 

Can anyone recommend reasonably priced chisels( say around $100-150 for
a set of six) that are tough enough to hold up to tropical hardwoods?
I have a set of Marples Blue Chip which I always thought were fairly
decent chisels and a good value. Recently I was trying to make some
cross grain cuts in some jatoba. The cut was a heavy paring cut and I
was using a deadblow mallet to hasten it along. I was very chagrined to
discover that I actually chipped the steel on the chisel. Is possible
that my chisels are defective? Am I asking too much of the Marples? In
either case I definitely need new chisels to cut the very obstinate
jatoba. Any recommendations from users who have actually used chisels
that can cut wood like this?

Paul

Chisels for tropical hardwoods?
 

"Lincoln Terns" wrote...

Can anyone recommend reasonably priced chisels( say around $100-150 for
a set of six) that are tough enough to hold up to tropical hardwoods?
[...]

The Marples morticing chisels are beefier than standard chisels and might do
the trick. You could also try regrinding your chisels to 35 or maybe even
40 degrees. That's really a better angle for mortising than for paring, but
if the wood is that hard it could help keep the edges from chipping.



Moonstone Plovers
www.tjwoodworking.com

Chisels for tropical hardwoods?
 

Fri, Dec 1, 2006, 3:32pm (EST-3) (Lincoln*Terns)
doth sayeth:
snipThe cut was a heavy paring cut and I was using a deadblow mallet
to hasten it along. snip

You can quote me on this, but it won't mean a thing. LOL I have
the feeling that using a deadblow mallet could well have had something
to do with damaging the chisel. I'd think a carving mallet would have
been better.

I've got an inexpensive set of Hf chisels. I've even used them on
som almost rock hard pallet wood, using turned carving mallts, sometimes
whacking the Hell out of them. I have to resharpen them oftener than
the pricey stuff, but no signs of damage, except the more rapid dulling.



JOAT
I am, therefore I think.

Chisels for tropical hardwoods?
 

If the steel chips before dulling, you need a steeper angle.

"Lincoln Terns" wrote in message
ups.com...
Can anyone recommend reasonably priced chisels( say around $100-150 for
a set of six) that are tough enough to hold up to tropical hardwoods?
I have a set of Marples Blue Chip which I always thought were fairly
decent chisels and a good value. Recently I was trying to make some
cross grain cuts in some jatoba. The cut was a heavy paring cut and I
was using a deadblow mallet to hasten it along. I was very chagrined to
discover that I actually chipped the steel on the chisel. Is possible
that my chisels are defective? Am I asking too much of the Marples? In
either case I definitely need new chisels to cut the very obstinate
jatoba. Any recommendations from users who have actually used chisels
that can cut wood like this?

Paul

Chisels for tropical hardwoods?
 

CW wrote:
If the steel chips before dulling, you need a steeper angle.

Doh! ( dope slap to forehead) Thanks for all of the quick responses
pointing out the obvious and completely overlooked solution. I will
regrind and take another whack at the wood.

Chisels for tropical hardwoods?
 

I recommend you spend a little more and get the Lie-Nilesen chisels.

http://www.lie-nielsen.com/catalog.php?cat=521


Lincoln Terns wrote:
Can anyone recommend reasonably priced chisels( say around $100-150 for
a set of six) that are tough enough to hold up to tropical hardwoods?
I have a set of Marples Blue Chip which I always thought were fairly
decent chisels and a good value. Recently I was trying to make some
cross grain cuts in some jatoba. The cut was a heavy paring cut and I
was using a deadblow mallet to hasten it along. I was very chagrined to
discover that I actually chipped the steel on the chisel. Is possible
that my chisels are defective? Am I asking too much of the Marples? In
either case I definitely need new chisels to cut the very obstinate
jatoba. Any recommendations from users who have actually used chisels
that can cut wood like this?

Paul